• 상하수도학회지
• /
• 제18권3호
• /
• pp.377-384
• /
• 2004

In the present study, a feasibility of an advanced oxidation process using UV/Hydrogen peroxide($H_2O_2$) system equipped with a medium pressure lamp for secondary effluent reclamation was investigated. Initial concentration of $H_2O_2$ and pH were changed to determine the optimum operation condition for the system. The removal efficiency of color was than 80% with 14.3mg/L of initial $H_2O_2$ and 5 minute of contact time in the UV/$H_2O_2$ system. The color removal was analyzed using first-order reaction equation. The dependence of rate constant (k) on initial $H_2O_2$ represented the rational relationship with maximum value. Residual $H_2O_2$ caused increase of effluent COD, since analyzing agent, dichromate, reacted with $H_2O_2$ in the sample. Therefore, excess initial concentration of $H_2O_2$ would significantly affect effluent COD measurement. At pH variation experiment, both residual $H_2O_2$ and color showed peak in the neutral pH range with the same pattern. Effect of $H_2O_2$ dose also enhanced color removal but raised residual $H_2O_2$ problem in the continuous operation UV system. In conclusion, these results indicated that medium pressure UV/$H_2O_2$ system could be used to control color in the secondary effluent for reclamation and reuse.

• Transactions on Electrical and Electronic Materials
• /
• 제2권2호
• /
• pp.37-41
• /
• 2001

Photo catalytic characteristics of nano-sized TiO$_2$ powder with rutile phase produced using homogeneous precipitation process at low temperatures (HPPLT) were compared with those of commercial P-25 powder by Degussa Co. The TiO$_2$ powder by HPPLT showed very higher photoactivity in the removal rate, showing lower pH values in the solution, than the P-25 powder when eliminating metal ions such as Pb and Cu from aqueous metal-EDTA solutions. This can be inferred the more rapid photo-oxidation or -reduction of metal ions from the aqueous solution, together with relatively higher efficiencies in the use of electron-hole pair formed on the surface of TiO$_2$ particle, under UV light irradiation. Also, in the view of the TiO$_2$ particle morphology, compared to the well-dispersed spherical P-25 particle, the agglomerated TiO$_2$ particle by HPPL T consists of acicular typed primary particle with the thickness ranged of 3∼7 nm, which would be more effective to the photocatalytic reactions without electron-hole recombination on the surface of the TiO$_2$ particle under the UV light irradiation. It is, therefore, thought that the higher photo activity of the rutile TiO$_2$ powder by HPPLT in the aqueous solutions resulted from having its higher specific surface area as well as acicular shape primary particle with very thin thickness.

• 상하수도학회지
• /
• 제18권6호
• /
• pp.731-741
• /
• 2004

The purpose of this study was to evaluate the potential of a gamma ray irradiation to decompose hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in an aqueous solution. The decomposition reaction of RDX by gamma ray irradiation was a first-order kinetic over the applied initial concentrations (10-40mg/L). The dose constant was strongly dependent on the initial concentration of the RDX. The removal of RDX was more efficient at pH below 3 and at pH above 11 than at neutral pH (pH 5-9). The required irradiation dose to remove 99% of the RDX (40mg/L) was 4, 8 and 1 kGy, at pH 2, 7 and 13, respectively. The dose constant was increased by two folds and over twelve folds at pH 2 and 13, respectively, when compared with that at pH 7. When an irradiation dose of 20 kGy was applied, the removal efficiencies of TOC were 80, 57 and 91% at pH 2, 7 and 13, respectively. Ammonia and nitrate were detected as the main nitrogen byproducts of RDX and formic acid was detected as an organic byproduct. The results showed that a gamma ray irradiation was an attractive method for the decomposition of RDX in an aqueous solution and it was found that a strong alkaline pH over 12 should be applied to the decomposition reaction of RDX.

• Environmental Engineering Research
• /
• 제10권3호
• /
• pp.138-143
• /
• 2005

Laboratory batch experiments were conducted to evaluate the Fenton degradation rates of phenanthrene. Fenton reactions for the degradation of phenanthrene were carried out with aqueous and slurry phase, to investigate the effects of sorption of phenanthrene onto solid phase. Various types of surfactants and electrolyte solutions were used to evaluate the effects on the phenanthrene degradation rates by Fenton's reaction. A maximum 90% removal of phenanthrene was achieved in aqueous phase with 0.9% of $H_2O_2$ and 300 mg/L of $Fe^{2+}$ at pH 3. In aqueous phase reaction, inhibitory effects of synthetic surfactants on the removal of phenanthrene were observed, implying that surfactant molecules acted as strong scavenger of hydroxyl radicals. However, use of $carboxymethyl-{\beta}-cyclodextrin$ (CMCD), natural surfactant, showed a slight enhancement in the degradation of phenanthrene. It was considered that reactive radicals formed at ternary complex were located in close proximity to phenanthrene partitioned into CMCD cavities. It was also show that Fenton degradation of phenanthrene were greatly enhanced by addition of NaCl, indicating that potent radical ion ($OCI^-$) played an important role in the phenanthrene degradation, although chloride ion might be acted as scavenger of radicals at low concentrations. Phenanthrene in slurry phase was resistant to Fenton degradation. It might be due to the fact that free radicals were mostly reacting with dissolved species rather than with sorbed phenanthrene. Even though synthetic surfactants were added to increase the phenanthrene concentration in dissolved phase, low degradation efficiency was obtained because of the scavenging of radicals by surfactants molecules. However, use of CMCD in slurry phase, showed a slight enhancement in the phenanthrene degradation. As an alternative, use of Fenton reaction with CMCD could be considered to increase the degradation rates of phenanthrene desorbed from solid phase.

• 한국방재학회 논문집
• /
• 제11권2호
• /
• pp.179-183
• /
• 2011

본 연구에서는 광 반응기 내부의 영향반경을 평가하기 위해 자외선(UV-C) 램프의 강도와 photochemical에 의한 OH 라디칼 생성량을 측정하였다. 또한 $TiO_2$ (Degussa P-25)를 농도별로 첨가하여 자외선 램프의 영향반경을 측정하였다. 광 반응기는 아크릴 재질의 bath 타입을 사용하였고, 254 nm의 파장을 가진 UV-C 자외선 램프를(SANKYO DENKI, 지름 : 2.2 cm, 길이 : 18.5 cm) 사용하였다. 램프의 소비전력은 10.5 W이고, OH 라디칼 생성량을 측정하기 위해 KI dosimetry를 사용하였다. 실험 결과로부터 광 반응기에서 자외선의 강도가 0.367 mW/$cm^2$이상 조사되어야하고, 거리는 13 cm 이내에서 OH 라디칼 생성에 영향을 미치는 것으로 나타났다. 또한 광촉매 반응기에서는 촉매의 농도로 인해 자외선의 영향반경이 매우 감소하는 것을 확인할 수 있었다.

• 상하수도학회지
• /
• 제33권4호
• /
• pp.243-250
• /
• 2019

This objective of this study was to investigate the degradation characteristics of phenol, a refractory substance, by using a submerged dielectric barrier discharge (DBD) plasma reactor. To indirectly determine the concentration of active species produced in the DBD plasma, the dissolved ozone was measured. To investigate the phenol degradation characteristics, the phenol and chemical oxygen demand (COD) concentrations were evaluated based on pH and the discharge power. The dissolved ozone was measured based on the air flow rate and power discharged. The highest dissolved ozone concentration was recorded when the injected air flow rate was 5 L/min. At a discharge power of 40W as compared to 70W, the dissolved ozone was approximately 2.7 - 6.5 times higher. In regards to phenol degradation, the final degradation rate was highest at about 74.06%, when the initial pH was 10. At a discharged power of 40W, the rate of phenol decomposition was observed to be approximately 1.25 times higher compared to when the discharged power was 70W. It was established that the phenol degradation reaction was a primary reaction, and when the discharge power was 40W as opposed to 70W, the reaction rate constant(k) was approximately 1.72 times higher.

• Journal of Ceramic Processing Research
• /
• 제19권5호
• /
• pp.372-377
• /
• 2018

MgO or gadolinium-doped ceria (GDC, $Ce_{0.9}Gd_{0.1}O_{2-{\delta}}$) was added as a promoter to improve the oxygen transfer kinetics of $MgMnO_3$ oxygen carrier material for chemical looping combustion. Neither MgO nor GDC reacted with $MgMnO_3$, even at the high temperature of $1100^{\circ}C$. The average oxygen transfer capacities of $MgMnO_3$, 5 wt% $MgO-MgMnO_3$, and 5 wt% $GDC-MgMnO_3$ were 8.74, 8.35, and 8.13 wt%, respectively. Although the addition of MgO or GDC decreased the oxygen transfer capacity, no further degradation was observed during their use in 5 redox cycles. The addition of GDC significantly improved the conversion rate for the reduction reaction of $MgMnO_3$ compared to the use of MgO due to an increase in the surface adsorption process of $CH_4$ via oxygen vacancies formed on the surface of GDC. On the other hand, the conversion rates for the oxidation reaction followed the order 5 wt% $GDC-MgMnO_3$ > 5 wt% $MgO-MgMnO_3$ >> $MgMnO_3$ due to morphological change. MgO or GDC particles suppressed the grain growth of the reduced $MgMnO_3$ (i.e., (Mg,Mn)O) and increased the specific surface area, thereby increasing the number of active reaction sites.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2021년도 학술발표회
• /
• pp.421-421
• /
• 2021

도시화, 산업화로 인해 하수처리장 유입하수 내 질소 농도가 증가하면서 그에 따른 부영양화 발생, 수생태계에 독성을 미치는 등의 악영향 또한 증가하게 되었다. 하수 내 고농도 질소를 처리하기 위해 1990년 초 연구가 시작되어 현재 보편적으로 사용되고 있는 생물학적 질소 제거 공정은 산소공급과 외부탄소원 보충 과정에서 상당한 비용이 소요된다. 이와 같은 문제점이 대두됨에 따라 고도의 질소 제거 공정이 요구되면서, 경제적으로 개선이 이루어져 기존의 질산화·탈질 공정보다 효율적인 혐기성 암모늄 산화 공정(ANaerobic AMMonium OXidation, ANAMMOX)이 제안되었다. ANAMMOX 공정은 혐기성 조건 아래 전자공여체와 전자수용체로써 암모니아성 질소와 아질산성 질소를 이용해 질소가스 형태로 질소를 제거하는 공정이다. 질산화·탈질 공정과 비교했을 때, 폭기과정에서의 산소요구량 감소, 외부탄소원 불필요, 질소 제거 과정 단축 등의 장점을 가진다. 본 연구는 수처리공정에서의 ANAMMOX 공정의 적용 가능성을 확인하고, 암모니아성 질소대비 아질산성 질소 비율에 따른 Mainstream ANAMMOX 공정의 효율 비교를 통해 공정의 안정성과 높은 제거효율을 확보할 수 있는 NH₄⁺ 대비 NO₂^- 비율을 도출하는데 목적이 있다. 실험실 규모의 Mainstream ANAMMOX 반응조에 적용한 비율은 선행연구를 비롯한 화학양론식에서 제시된 비율을 바탕으로 산정하였다. 1.00부터 1.30의 전체적인 비율을 Initial과 Advanced 2개의 구간으로 나누어 운전한 결과, 각 구간의 NH₄⁺ 제거효율은 각각 58~86%, 94~99%였다. NH₄⁺ 대비 NO₂^- 비율이 증가함에 따라 공정의 안정성이 확보되고, NH₄⁺ 및 총질소(TN) 제거효율이 증가하는 경향이 나타났다. 본 연구의 결과는 수처리공정에서의 안정적인 ANAMMOX 공정 적용을 유도하고, ANAMMOX 공정의 성능개선을 도모하는 연구의 기초로 활용될 수 있다.

• Journal of Electrochemical Science and Technology
• /
• 제14권4호
• /
• pp.388-396
• /
• 2023

Photoelectrochemical (PEC) water splitting is a vital source of clean and sustainable hydrogen energy. Moreover, the large-scale H₂ production is currently necessary, while long-term stability and high PEC activity still remain important issues. In this study, a GaN-based photoelectrode was modified by an additional NH₃ treatment (900℃ for 10 min) and its PEC behavior was monitored. The bare GaN exhibited a highly crystalline wurtzite structure with the (002) plane and the optical bandgap was approximately 3.2 eV. In comparison, the NH₃-treated GaN film exhibited slightly reduced crystallinity and a small improvement in light absorption, resulting from the lattice stress or cracks induced by the excessive N supply. The minor surface nanotexturing created more surface area, providing electroactive reacting sites. From the surface XPS analysis, the formation of an N-Ga-O phase on the surface region of the GaN film was confirmed, which suppressed the charge recombination process and the positive shift of E_FB. Therefore, these effects boosted the PEC activity of the NH₃-treated GaN film, with J values of approximately 0.35 and 0.78 mA·cm^-2 at 0.0 and 1.23 V_RHE, respectively, and an onset potential (V_on) of -0.24 V_RHE. In addition, there was an approximate 50% improvement in the J value within the highly applied potential region with a positive shift of V_on. This result could be explained by the increased nanotexturing on the surface structure, the newly formed defect/trap states correlated to the positive V_on shift, and the formation of a GaO_xN_1-x phase, which partially blocked the charge recombination reaction.

• 한국물환경학회지
• /
• 제40권1호
• /
• pp.36-46
• /
• 2024

Microplastics in water resources have been recognized as a serious problem. The discharge of microplastics from wastewater treatment plants is considered a major contributor to environmental pollution in water resources. However, a reliable analytical method for quantifying microplastics in wastewater treatment plants has not yet been established. This study proposes a reliable, quick, and easy analytical method for quantifying microplastics. For the removal of organic particles, preprocessing steps were applied including oxidation, sonication, washing, and sieving. Nile Red staining was used to visualize microplastics, and quantitative analysis was conducted using fluorescent imaging. The stained microplastics were ultimately quantified through image analysis software. Among the preprocessing steps, sonication and washing stages were particularly effective in efficiently removing interfering substances from wastewater, enhancing the accuracy of the microplastic analysis. Additionally, various solvents (methanol, acetone, and N-hexane) for the Nile Red staining solution were tested. When N-hexane was applied as the solvent, the quantity of stained microplastics was lower compared to methanol and acetone. This suggests that N-hexane has a greater potential of reducing false staining and counting of non-plastic particles. In summary, this research demonstrates a robust method for quantifying microplastics in wastewater treatment plants by employing effective preprocessing steps and optimizing the staining process with Nile Red and N-hexane.