• Macromolecular Research
• /
• v.14 no.6
• /
• pp.640-645
• /
• 2006

Polyethylene of bimodal molecular weight distribution was irradiated with an electron beam. The thermal and mechanical properties were examined by DSC, small and wide angle X-ray scattering and static tensile test according to the crystal morphology of the irradiated samples. The crystal morphology change upon irradiation, as revealed by wide angle X-ray scattering, correlated well with the changes in melting enthalpy, whereas the lamellar thickness and the amorphous gap thickness remained virtually unchanged at irradiation doses up to 500 kGy. Crosslinks in the crystal domains became evident at an energy level of 250 kGy, resulting in reduced crystallinity and crystal size of the (110) and (200) planes. The samples became stiff and brittle with increased irradiation dose, which seem to be more relevant to the amount of cross links than the crystal morphology changes.

• Journal of Magnetics
• /
• v.5 no.3
• /
• pp.85-89
• /
• 2000

The hysteretic characteristics of giant magnetoimpedance (GMI) profiles have been measured in Co-based amorphous ribbon with various anisotropy angles $\theta_k$, and they have been analyzed by using the Stoner-Wohl-farth model. Two-peaks behavior with a dip near zero field is revealed in the measured GMI profile at 10 MHz irrespective of $\theta_k$. The negligible hysteresis of the field fur the dip is close to the calculation assuming the magnetization jump from a metastable to stable state. However, the hysteretic asymmetry far the angle range of $20^\circ\leq\theta_k < 60^\circ$ is well described by the divergence in the calculation without the magnetization jump. The asymmetry for $\theta_k\geq60^\circ$ may be due to the divergence, but the shapes of measured profiles are quite different from the calculations with single peak near zero field, indicating that Stoner-Wohlfarth model can be well used to describe GMI characteristics for the anisotropy angle range of $20^\circ\leq\theta_k < 60^\circ$at the frequency of 10 MHz in Co-based amorphous ribbons.

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.229-235
• /
• 2002

Plasma source ion implantation (PSII) technique was utilized to improve the wettability of polystyrene surfaces. It is well known that treated surfaces undergo aging, leading to hydrophobic recovery with time. We investigated the aging effect of polystyrene thin film on the various molecular weights. Polystyrenes with several molecular weights ($M_w$ = 760, 2430, 31600, 115700, 280000, 903600) were treated in different experimental conditions including gas species and pulse energy, and their hydrophilicity was measured by contact angle goniometer. To study wettability decay as a function of the molecular weight, PSII-treated samples were aged at different temperatures. Hydrophobic recovery of high molecular weight polystyrene was much slower than that of low molecular weight, even at high temperatures. The methods used to characterize treated surfaces were water contact angle measurement, TOF-SIMS, XPS, SEM and AFM.

• Korean Journal of Materials Research
• /
• v.32 no.12
• /
• pp.553-559
• /
• 2022

In this work, the ablation behavior of monolith ZrB₂-30 vol%SiC (Z30S) composites were studied under various oxy-acetylene flame angles. Typical oxidized microstructures (SiO₂/SiC-depleted/ZrB₂-SiC) were observed when the flame to Z30S was arranged vertically. However, formation of the outmost glassy SiO₂ layer was hindered when the Z30S was tilted. The SiC-depleted region was fully exposed to air with reduced thickness when highly tilted. Traces of the ablated and island type SiO₂ were observed at intermediate flame angles, which clearly verified the effect of flame angle on the ablation of the SiO₂ layer. Furthermore, the observed maximum surface temperature of the Z30S gradually increased up to 2,200 ℃ proving that surface amorphous silica was continuously removed while monoclinic ZrO₂ phase began to be exposed. A proposed ablation mechanism with respect to flame angles is discussed. This observation is expected to contribute to the design of complex-shaped UHTC applications for hypersonic vehicles and re-entry projectiles.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.459-462
• /
• 2002

We report viewing angle characteristics of the Ultra-FFS TFT-LCD. The FFS mode is known to exhibit both a wide viewing angle and high transmittance, owing to the approximated in-plane rotation of the LC director. Nevertheless, in the bright state, the device shows bluish and yellowish color parallel and perpendicular to the LC director at off-normal directions since the LC director rotates onl.v in one direction, and in addition, the grey scale inversion exists in large oblique viewing angle. However, the Ultra-FFS shows no grey scale inversion and no color shift in wide viewing angle range.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.4
• /
• pp.350-355
• /
• 2007

Pad-eye is connected to crane with sling. When block is lift, pad-eye have a various applied force. Applied force on pad-eye is related to sling angle. Sling angle is decided by various parameters, including pad-eye location, sling length and crane location. Welded joint on pad-eye requires strength design because sling angle changes force on pad-eye. Strength design for welded joint of pad-eye will calculate with general mechanical design and FE analysis. FE analysis would become a useful tool in the analysis of welded joint. A commercial software(ANSYS 10.0) was used in the structural strength analysis for welded joint of pad-eye.

• Design & Manufacturing
• /
• v.17 no.1
• /
• pp.33-39
• /
• 2023

The ball end mill is a type of cutting tool that is widely used to process complex mold shapes including aspheric surfaces. Unlike the flat end mill in which the cutting edge is formed on the cylindrical handle, the cutting edge is formed from the cylindrical handle to the hemispherical shape, which is advantageous for processing curved shapes. However, since the cutting speed continuously changes during machining due to the helix angle of the cutting edge or the machining inclination angle, it is difficult to obtain a precise machined surface. Therefore, in this paper, machining was performed while changing the helix angle of the ball end mill and the angle of the machining slope under the same cutting conditions for STD 11 material, which is widely used as a mold material. Through this, the effect of the two variables on the roughness of the machined surface was analyzed. As a result, if the helix angle was 0 degrees, it showed the best surface roughness of Ra. 0.16 ㎛. When the helix angle was 20 degrees, the best surface roughness of Ra. 0.18 ㎛ was occurred.

• Proceedings of the Korean Society of Rheology Conference
• /
• 2000.11a
• /
• pp.37-40
• /
• 2000

• Proceedings of the KSRS Conference
• /
• v.1
• /
• pp.386-389
• /
• 2006

The sea surface wind speed (SSWS) derived by microwave radiometer can be contaminated by change of microwave brightness temperature owing to the angle between the sensor azimuth and the wind direction (Relative Wind Direction). We attempt to correct the contamination to the SSWS derived by Advanced Microwave Scanning Radiometer (AMSR) on Advanced Earth Observing Satellite II (ADEOS-II), by applying the method proposed by Konda and Shibata (2004). The improvement of accuracy of the SSWS estimation amounts to roughly 60% of the error caused by the RWD effect.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.290-292
• /
• 2007

A twisted nematic type liquid crystal electro-optic modulator (TN-LC modulator) was developed. The modulator used single polarizer and the reflection on-off ratio was maximized by optimization of twist angle and retardation of liquid crystal cell. The TNLC modulator shows better sensitivity and response time than conventional liquid crystal modulator.