• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.15-16
• /
• 2022

In order to examine the adhesion characteristics of road pavement according to environmental conditions, the freezing time of cement mortar and the adhesion performance between ice and pavement were evaluated depending on the presence or absence of polymer and water repellent. As a result of measuring the ice formation time, it was found that there was no delay when a polymer was added, but the complete freezing time was delayed when a water repellent was added. As a result of measuring the strength of ice adhesion, it was found that the bonding force between ice and the surface of the test body was greatly generated in the test body without water repellent. In the case of a test specimen to which a water repellent was added, it was found that the bonding strength between the test specimen surface and ice was reduced.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.42-46
• /
• 2005

In microelectronics packaging, the reliability of the metal/polymer interfaces is an important issue because the adhesion strength between dissimilar materials is often inherently poor. The modification of polymer sufaces by ion beam irradiation and rf plasma are commonly used to enhance the adhesion strength of the interface. T-peel strengths were measured using a Cu/polyimide system under varying $Ar^+$ ion beam irradiation pretreatment conditions. The measured T-peel strength showed reversed camel back shape regarding the fixed metal-layer thickness, which was quite different from the results of the $90^{\circ}$ peel test. The elementary analysis suggests that the variation of the T-peel strength is a combined outcome of the plastic bending work of the metal and polymer strips. The results indicate that the peel strength increases with $Ar^+$ ion beam irradiation energy at the fixed metal-layer thickness.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.1-8
• /
• 2006

In this study, effect of sputtering after plasma nitriding and before PVD coating on the microstucture, microhardness, surface roughness and the adhesion strength of CrN thin films were investigated. Experimental results showed that this sputtering process not only removed surface compound layer which formed during a plasma nitriding process but also induced an alteration of the surface of plasma nitrided substrate in terms of microhardness distribution and surface roughness, which in turn affected the adhesion strength of PVD coatings. After sputtering, microhardness distribution showed general decrease and the surface roughness became increased slightly. The critical shear stress measured from the scratch test on the CrN coatings showed an approximately twice increase in the binding strength through the sputtering prior to the coating and this could be attributed to a complete removal of compound layer from the plasma nitrided surface and to an increase in the surface roughness after sputtering.

• Journal of Adhesion and Interface
• /
• v.3 no.4
• /
• pp.37-43
• /
• 2002

A number of thin-film deposition technologies have been developed. However, even a thin film whose properties are excellent may not be used as long as the adhesion strength between the thin film and the substrate is poor. For thin films, the adhesion strength is as important as the properties. In the present article, relation between interface structure and thin film adhesion, and factors affecting thin film adhesion are reviewed. Two kinds of factors, internal factors and external factors, affect thin film adhesion. Such factors as composition, structure, and reactivity of both thin film and substrate as well as surface roughness of the substrate and residual stress of the thin film belong to internal factors. And such factors as load, temperature, humidity, and corrosive environment belong to external factors. It is also reviewed that how we can control the internal factors and the external factors to enhance or keep the adhesion strength.

• Journal of Fashion Business
• /
• v.23 no.2
• /
• pp.77-88
• /
• 2019

One way of appling 3D printing to garments is through the combination of 3D polymer filaments in textile fabrics. it is essential to understand the interface between the polymer and the 3D composite fabric in order to enhance the adhesion strength between the polymers and the peeling strength between the fabric and the polymer. In this study, the adhesion of composite printed specimens using a combination of fabric and polymers for 3D printing was investigated, and also the change in adhesion was investigated after the composite fabric printed with polymers was subjected to constant pressure. Through this process, the aims to help develop and utilize 3D printing textures by providing basic data to enhance durability of 3D printing composite fabrics. The measure of the peeling strength of the composite fabric prepared by printing on a fabric using PLA, TPU, Nylon polymer was obtained as follows; TPU polymer for 3D printing showed significantly higher peel strength than polymers of composite fabric using PLA and Nylon polymer. In the case of TPU polymer, the adhesive was crosslinked because of the reaction between polyurethane and water on the surface of the fabric, thus increasing the adhesion. It could be observed that the adhesion between the polymer and the fiber is determined more by the mechanical effect rather than by its chemical composition. To achieve efficient bonding of the fibers, it is possible to modify the fiber surface mechanically and chemically, and consider the deposition process in terms of temperature, pressure and build density.

• Journal of Adhesion and Interface
• /
• v.5 no.4
• /
• pp.1-8
• /
• 2004

UV-curable pressure sensitive adhesives were prepared by blending acrylic copolymer, copolymerized with butyl acrylate, acrylic acid and methyl methacrylate by solution polymerization, and trimethylolpropane triacrylate. The PSAs were evaluated by adhesion strength with varying UV dose, and also glass transition temperature ($T_g$) of PSAs were measured. When exposed on UV irradiation, the PSAs showed the decreased adhesion strength and increased $T_g$. And following UV irradiation, the PSAs did not leave any residue on wafer after peel off PSA.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.2
• /
• pp.223-231
• /
• 2017

This work was conducted to investigate on the effect of urea-formaldehyde (UF) resin viscosity on plywood adhesion. The viscosity of UF resin was controlled either by adjusting the condensation reaction during its synthesis to obtain different target viscosities (100, 200 and 300 mPa.s) at two levels of formaldehyde/urea (F/U) mole ratios (1.0 and 1.2) or by adding different amounts (10, 20 and 30%) of wheat flour into the resins for the manufacture of plywood. When the viscosity of UF resin increased by the condensation reaction, the adhesion strength of plywood bonded with UF resin of 1.2 F/U mole ratio consistently increased, while those bonded with the 1.0 F/U mole ratio resin slightly decreased, suggesting a difference in the adhesion in plywood. However, the adhesion strength of plywood decreased as the viscosity increased by adding wheat flour, regardless of F/U mole ratio. The manipulation of UF resin viscosity by adjusting the condensation reaction was much more efficient than by adding wheat flour in improving the adhesion performance of plywood. These results indicated that a way of controlling the viscosity of UF resin adhesives has a great influence to their adhesion in plywood.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1798-1802
• /
• 2007

Adhesion strength of single layer ceramic capacitor sheet was measured using a peel testing system developed in this study. The peel test specimens with various dimensions were prepared from the ceramic sheet cast on the PET film. In peel test, the sheet specimen was adhered on the glass jig floating on the liquid media, which was designed to minimize the friction, and the specimen was then pulled up by micro-actuator. During the separation of the sheet from the PET film, peel force was measured. To normalize the testing condition, 3 different widths of the specimen were selected: 5, 10 and 20 mm. was used Furthermore, testing speed effect was investigated in this study. From the resullts using various testing conditions, the standard method for the peel strength testing may be suggested. Based on the testing condition, effect of peel angle on the strength was experimentally examined. It was found that the adhesive strength for the ceramic sheet is nearly identical, irrespective of the specimen width ranged from 5 to 20 mm, while the adhesive strength was increased with increasing testing speed. Furthermore, the strength was shown to be dependent on the peel angle.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.232-233
• /
• 2014

Recently, water treatment facility is usually eastablished in underground, and waterproofing and anti-corrosion materials for concrete structures applied water treatment tank is developing in various ways. However, as the limit of research focused on durability improvement of top coating material, it is insufficient to study on the adhesion strength between the concrete surface and primer. Therefore, there is to confirm the adhesion of between concrete surface and the three primers used as anti-corrosion waterproofing materials, and to investigate the properties of adhesion strength according to the condition such as wet codition and water pressure condition of the concrete surface in this study.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.3
• /
• pp.73-81
• /
• 1997

This study was to find the best adhesive condition comparing mechanical property in case of hot-melt adhesion using glue-gun, ultrasonic welding with adhesion and only ultrasonic welding in order to adhere thermoplastic resin of polyethylene (PE) in which reliable adhesion was resulted in case of ultrasonic welding with same materials of PE. The best welding condition were acquired at welding time 1 second, welding pressure 250kPa for PE-PE where welding time and welding pressure were increased in accordance with the increase of material strength. At the best ultrasonic welding conditions, bonding strength of PE-PE welding was about 21MPa of which material have tensile strength of 24MPa. Through the analysis of microscophic test for ultrasonic welding structure, it was distinguished between well welded structure with higher intermolecule flow and bad welded structure with lower flow, of which result is mostly correspond with the result of tensile strength test.