• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2424-2426
• /
• 2002

This paper proposes an adaptive control method of partially known system and shows its application result to control for two-wheeled WMR. The controlled system is stable in the sense of Lyapunov stability. To design a tracking controller for welding path reference, an error configuration is defined and the controller is designed to drive the error to zero as fast as desired. Moments of inertia of system are considered to be unknown system parameters. Their values are estimated using update laws in adaptive control scheme. The effectiveness of the proposed controller is shown through simulation results.

• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.118-127
• /
• 1997

With the trend towards welding automation and robotization, mathematical models for studying the influence of various variables on the weld bead geometry in gas metal arc (GMA) welding process are required. Partial penetration, single-pass bead-on-plate welds using the GMA welding process were fabricated in 12mm mild steel plates employed four different process variables. Experimental results has been designed to investigate the analytical and empirical formulae, and develop mathematical equations for understanding the relationship between process variables and weld bead geometry. The relationships can be usefully employed not only for open loop process control, but also for adaptive control provided that dynamic sensing of process output is performed.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.31-38
• /
• 2001

For the horizontal fillet welding with one plate in a vertical position, there will be a higher tendency of weld metal falling down rather than for the butt-welding in flat position. Such phenomenon could bring about the overlap or deflection of weld pool, and consequently induce the poor mechanical strength of weldments. Therefore, a precise position control of welding torch in conjunction with the weld qualify plays an important role in welding robot applications. In the present study, an experimental method was proposed for deriving a mathematical model between the leg length and the welding conditions. Finally, an algorithm was proposed for weld seam tracking and improvement of the weld quality. The reliability of the proposed algorithm was evaluated through various experiments, which showed that the proposed algorithm can be very effective for tracking the weld line and simultaneously achieving the sound weld bead.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.36-41
• /
• 1997

With the trend towards welding automation and robozation, mathematical models for studying the influence of various parameters on the weld bead geometry in Gas Metal Arc(GMA) welding process are required. The results of bead on plate welds deposited using the GMA welding process has enabled mathematical relationships to be developed that model the weld bead geometry. Experimental results were compared to outputs obtained using existing formulae that correlate process input variables to output parameters and subsequent modelling was performed in order to better predict the output of the GMA welding process. The aim of this work was to explain the relationships between GMA welding variables and weld bead geometry and thus, be able to predict input weld bead size. The relationships can be usefully employed for open loop process control and also for adaptive control provided that dynamic sensing of process output is performed.

• Journal of Welding and Joining
• /
• v.17 no.4
• /
• pp.39-45
• /
• 1999

The procedure of robotic Gas metal Arc (GMA) welding in order to achieve the optimized bead geometry needs the selection of suitable process parameters such as arc current, welding voltage, welding speed. It is required the relationships between process parameters and bead geometry. The objective of this paper is to develop the algorithm that enables the determination of process parameters from the optimized bead geometry for robotic GMA welding. It depends on the inversion of empirical equations derived from multiple regression analysis of the relationships between the process parameters and the bead dimensions using the least square method. The method not only directly determines those parameters which will give the desired set of bead geometry, but also avoids the need to iterate with a succession of guesses employed Finite Element Method(FEM). These results suggest that process parameter from experimental equation for robotic GMA welding may be employed to monitor and control the bead geometry in real time.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.321-329
• /
• 2000

Welding is essential for the manufacture of a range of engineering components which may vary from very large structures such as ships and bridges to very complex structures such as aircraft engines, or miniature components for microelectronic applications. Especially, a domestic situation of the welding automation is still depend on the arc sensing system in comparison to the vision sensing system. Specially, the gap-detecting of workpiece using conventional arc sensor is proposed in this study. As a same principle, a welding current varies with the size of a welding gap. This study introduce to the fuzzy membership filter to cancel a high frequency noise of welding current, and ART2 which has the competitive learning network classifies the signal patterns the filtered welding signal. A welding current possesses a specific pattern according to the existence or the size of a welding gap. These specific patterns result in different classification in comparison with an occasion for no welding gap. The patterns in each case of 1mm, 2mm, 3mm and no welding gap are identified by the artificial neural network.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.53-60
• /
• 2014

The automatic arc welding is generally accepted as the preferred joining technique and commonly chosen for assembly of large metal structures such as in areas of automotive, aircraft and shipbuilding due to its joint strength, reliability, and low cost compared to other joint processes. Recently, several mathematical models have been developed and studied for control and monitoring welding quality, productivity, microstructure and weld properties in arc welding processes. This study indicates the prediction of process parameters for the expected welding quality with accordance to the adaptive GTA welding process. Furthermore, the mathematical models is also develop to aid the selection of an optimal welding process as the generation of process controls to predict the bead geometry as a function output parameters in the GTA welding process. The developed models through this study showed comparatively excellent predicted results, and will extend to other welding processes to integrate an optimized system for the robotic welding process.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.77-79
• /
• 2006

While RSW(Resistance Spot Welding) have been the most successful sheet metal joining process in automotive industry, there are certain qualify issues due to the control system and its application process. Recent materials and coatings make the process more complicated resulting in new challenges for quality welds. In this research, an intelligent RSW system with adaptive control algorithm is introduced to overcome typical RSW issues and its applications to automotive body assembly are presented.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.5
• /
• pp.400-409
• /
• 2012

It is not easy to know the accurate mass and mass moment of inertia of robot. Because of this uncertainty, error may exist when we control the robot based on the inaccurate mass information. Moreover the properties of the portable robot can change during its operation. Therefore we developed the motion simulator based on the adaptive control. First, the computed torque control was carried out in order to minimize an error between target angles and real angles. The computed torque control is based on the equation of robot motion, which is derived from the Lagrange-Euler equation. To minimize the error between the real model and the approximated model, the adaptive control was carried out. During this simulation, the interference check was also carried out. The interference check verifies that the robot can move successfully without any collision.

• Journal of Welding and Joining
• /
• v.8 no.1
• /
• pp.23-30
• /
• 1990

The robotic welding has been adapted positively in many welding shops forthe purpose of improving the welding efficiency and liberating operators from the severe working atmosphere. But for a large-size structure with thick plates like ship-building and every kind of plants manufacturing, the application of the arc welding robots is not established yet. The reason is assumed that the conventional arc welding robots are not adaptive for multi-pass welding of thick plates whose grooves are not so accurate. As one solution to this problem, a guidance system which uses the welding arc itself as a sensor is largely used. In this study the velocity controller which changes the tip to workpiece distance for regulating the weld proposed. The proportional and integral gain of velocity controller were determined by using the computer simulation of the control system, and the simulation results compared with the experimental ones. It was revealed that the developed control system using the arc sensor principle has a good capability of tracking the weld joint, although some more studies will be needed to refine the model of arc current.