• 제목/요약/키워드: actual thickness

검색결과 429건 처리시간 0.028초

IPMC 작동기의 기계적 물성에 관한 연구 (A Study on Mechanical Properties of IPMC actuators)

  • 김홍일;김대관;한재흥
    • Composites Research
    • /
    • 제20권3호
    • /
    • pp.50-54
    • /
    • 2007
  • 본 연구에서는 IPMC의 기본적인 기계적 특성을 알아보았다. 기전폴리머의 한 종류인 IPMC는 굽힘형 작동, 가벼움, 저전력 소모, 유연성 등의 많은 장점을 가진 재료이다. 따라서 IPMC는 생체모방형 작동기와 센서로서 많은 가능성을 가지고 있다. 이런 가능성을 바탕으로 IPMC를 실제로 응용하기 위하여 IPMC의 변형, 구동력, 주파수 응답 등 기본적인 기계적 특성을 연구하였다. 우선 이온교환폴리머의 한 종류인 네피온 용액을 사용하여 여러 가지 두께의 네피온 막을 만들고, 무전해 도금을 통해 IPMC를 제작하였다. 이렇게 제작된 IPMC의 규격, 인가 전압에 따른 변형, 구동력, 주파수 응답 특성에 관한 실험을 수행하고, 실험 결과를 통해 IPMC 성능의 실험식과 등가 강성 모델을 수립하였다.

Field investigation and numerical study of ground movement due to pipe pile wall installation in reclaimed land

  • Hu Lu;Rui-Wang Yu;Chao Shi;Wei-Wei Pei
    • Geomechanics and Engineering
    • /
    • 제34권4호
    • /
    • pp.397-408
    • /
    • 2023
  • Pipe pile walls are commonly used as retaining structures for excavation projects, particularly in densely populated coastal cities such as Hong Kong. Pipe pile walls are preferred in reclaimed land due to their cost-effectiveness and convenience for installation. However, the pre-bored piling techniques used to install pipe piles can cause significant ground disturbance, posing risks to nearby sensitive structures. This study reports a well-documented case history in a reclamation site, and it was found that pipe piling could induce ground settlement of up to 100 mm. Statutory design submissions in Hong Kong typically specify a ground settlement alarm level of 10 mm, which is significantly lower than the actual settlement observed in this study. In addition, lateral soil movement of approximately 70 mm was detected in the marine deposit. The lateral soil displacement in the marine deposit was found to be up to 3.4 and 3.1 times that of sand fill and CDG, respectively, mainly due to the relatively low stiffness of the marine deposit. Based on the monitoring data and site-investigation data, a 3D numerical analysis was established to back-analyze soil movements due to the installation of the pipe pile wall. The comparison between measured and computed results indicates that the equivalent ground loss ratio is 20%, 40%, and 20% for the fill, marine deposit and CDG, respectively. The maximum ground settlement increases with an increase in the ground loss ratio of the marine deposit, whereas the associated influence radius remains stationary at 1.2 times the pipe pile wall depth (H). The maximum ground settlement increases rapidly when the thickness of marine deposit is less than 0.32H, particularly for the ground loss ratio of larger than 40%. This study provides new insights into the pipe piling construction in reclamation sites.

유전 센서 및 광섬유 센서를 이용한 EMC 유효 경화 수축 측정 (Measurement of effective cure shrinkage of EMC using dielectric sensor and FBG sensor)

  • 백정현;박동운;김학성
    • 마이크로전자및패키징학회지
    • /
    • 제29권4호
    • /
    • pp.83-87
    • /
    • 2022
  • 최근 반도체 패키지 두께가 점점 얇아짐에 따라 휨(warpage) 문제가 대두되고 있다. 휨(warpage)은 패키지 구성요소들 간의 물성 차이로 인해 발생하기 때문에, 휨(warpage)을 예측하기 위해서는 주된 구성요소인 EMC(Epoxy molding compound)의 정확한 물성 파악이 필수적으로 요구된다. 특히 EMC는 경화 공정 중 경화 수축을 보이는데, 겔점 이후에 발생하는 유효 경화 수축은 휨(warpage) 발생의 핵심 요소이다. 본 연구에서는 유전 센서를 이용해 측정한 소실 계수로부터 실제 반도체 패키지 경화 공정 동안 발생하는 EMC의 겔점이 정의되었다. 유전 센서로부터 얻은 결과를 분석하기 위해 DSC(Differential scanning calorimetry) 시험과 rheometer 시험이 수행되었다. 그 결과, 유전 측정법이 EMC 경화상태 모니터링에 효과적인 방법임이 검증되었다. 유전 측정과 동시에 광섬유 센서를 이용해 EMC의 경화 공정 중 변형률 변화 추이가 함께 측정되었다. 위 결과들로부터 경화 공정 중 발생하는 EMC의 유효 경화 수축이 측정되었다.

Genetic evaluation for economic traits of commercial Hanwoo population using single-step GBLUP

  • Gwang Hyeon Lee;Khaliunaa Tseveen;Yoon Seok Lee;Hong Sik Kong
    • 한국동물생명공학회지
    • /
    • 제38권4호
    • /
    • pp.268-274
    • /
    • 2023
  • Background: Recently, the single-step genomic best linear unbiased prediction (ssGBLUP) method, which incorporates not only genomic information but also phenotypic information of pedigree, is under study. In this study, we performed a ssGBLUP analysis on a commercial Hanwoo population using phenotypic, genotypic, and pedigree data. Methods: The test population comprised Hanwoo 1,740 heads raised in four regions of Korea, while the reference population used Hanwoo 18,499 heads raised across the country and two-generation pedigree data. Analysis was performed using genotype data generated by the Hanwoo 50 K SNP beadchip. Results: The mean Genome estimated breeding values (GEBVs) estimated using the ssGBLUP methods for carcass weight (CWT), eye muscle area (EMA), back fat thickness (BFT), and marbling score (MS) were 7.348, 1.515, -0.355, and 0.040, respectively, while the accuracy of each trait was 0.749, 0.733, 0.769, and 0.768, respectively. When the correlation analysis between the GEBVs as a result of this study and the actual slaughter performance was confirmed, CWT, EMA, BFT, and MS were reported to be 0.519, 0.435, 0.444, and 0.543, respectively. Conclusions: Our results suggest that the ssGBLUP method enables a more accurate evaluation because it conducts a genetic evaluation of an individual using not only genotype information but also phenotypic information of the pedigree. Individual evaluation using the ssGBLUP method is considered effective for enhancing the genetic ability of farms and enabling accurate and rapid improvements. It is considered that if more pedigree information of reference population is collected for analysis, genetic ability can be evaluated more accurately.

쉘 모델을 이용한 공기 포일 스러스트 베어링의 열-유체-구조 연동 해석 (Thermo-Fluid-Structure Coupled Analysis of Air Foil Thrust Bearings using Shell Model)

  • 윤종완;문소연;박상신
    • Tribology and Lubricants
    • /
    • 제40권1호
    • /
    • pp.17-23
    • /
    • 2024
  • This study analyzes the thermal effects on the performance of an air foil thrust bearing (AFTB) using COMSOL Multiphysics to approximate actual bearing behavior under real conditions. An AFTB is a sliding-thrust bearing that uses air as a lubricant to support the axial load. The AFTB consists of top and bump foils and supports the rotating disk through the hydrodynamic pressure generated by the wedge effect from the inclined surface of the top foil and the elastic deformation of the bump foils, similar to a spring. The use of air as a lubricant has some advantages such as low friction loss and less heat generation, enabling air bearings to be widely used in high-speed rotating systems. However, even in AFTB, the effects of energy loss due to viscosity at high speeds, interface frictional heat, and thermal deformation of the foil caused by temperature increase cannot be ignored. Foil deformation derived from the thermal effect influences the minimum decay in film thickness and enhances the film pressure. For these reasons, performance analyses of isothermal AFTBs have shown few discrepancies with real bearing behavior. To account for this phenomenon, a thermal-fluid-structure analysis is conducted to describe the combined mechanics. Results show that the load capacity under the thermal effect is slightly higher than that obtained from isothermal analysis. In addition, the push and pull effects on the top foil and bump foil-free edges can be simulated. The differences between the isothermal and thermal behaviors are discussed.

마이크로 광학 패턴이 있는 차량용 후육 라이트 가이드의 CAE 및 사출성형에 관한 기초연구 (A study on CAE and injection molding of automotive thick-walled light guide with micro-optical patterns)

  • 이동원;김종수;이현화;이성희
    • Design & Manufacturing
    • /
    • 제17권3호
    • /
    • pp.8-14
    • /
    • 2023
  • In this study, basic research was conducted on manufacturing technology of thick-walled light guide a component that controls the light source of automobile lamps. As a preliminary study for manufacturing the final injection molded parts, a model for analyzing the influence of micro patterns on light guides is presented. The optical characteristics of the light guide were analyzed according to the change of the curvature radius of the micro-optical pattern, and the injection molding characteristics of the light guide according to the change of injection molding conditions were analytically evaluated. It was confirmed that the luminance uniformity improves as the R value decreases for changes in the micro-pattern R value, but it was confirmed that there are technical limitations in actual injection mold core processing and high-replication injection molding. Injection molding analysis showed that cooling channel design is very important compared to general injection molding due to thick-wall characteristics and thickness variation. It was also confirmed that the cooling channel has a great influence on the cycle time and birefringence result due to residual stress. As a result of analyzing the influence of filling time, holding condition, and cooling on shrinkage, it was found that the cooling water temperature has a significant effect on the shrinkage of ultra-fine light guide parts, and the holding condition also has a significant effect.

PC 접합부의 실물 성능실험을 통한 기계식이음 구조성능 평가 (Evaluation of Mechanical Joint Structural Performance through Actual Performance Testing of PC Connections)

  • 김재영;김용남;서민정;김범진;김승직;이기학
    • 한국지진공학회논문집
    • /
    • 제28권3호
    • /
    • pp.129-139
    • /
    • 2024
  • In this study, the SBC system, a new mechanical joint method, was developed to improve the constructability of precast concrete (PC) beam-column connections. The reliability of the finite element analysis model was verified through the comparison of experimental results and FEM analysis results. Recently, the intermediate moment frame, a seismic force resistance system, has served as a ramen structure that resists seismic force through beams and columns and has few load-bearing walls, so it is increasingly being applied to PC warehouses and PC factories with high loads and long spans. However, looking at the existing PC beam-column anchorage details, the wire, strand, and lower main bar are overlapped with the anchorage rebar at the end, so they do not satisfy the joint and anchorage requirements for reinforcing bars (KDS 41 17 00 9.3). Therefore, a mechanical joint method (SBC) was developed to meet the relevant standards and improve constructability. Tensile and bending experiments were conducted to examine structural performance, and a finite element analysis model was created. The load-displacement curve and failure pattern confirmed that both the experimental and analysis results were similar, and it was verified that a reliable finite element analysis model was built. In addition, bending tests showed that the larger the thickness of the bolt joint surface of the SBC, the better its structural performance. It was also determined that the system could improve energy dissipation ability and ductility through buckling and yielding occurring in the SBC.

인체 및 인형 팬톰에서 전신방사선조사시 열형광선량계(TLD)를 이용한 선량분포 균일성 확인 (In vivo and in vitro Confirmation of Dose Homogeneity in Total Body Irradiation with Thermoluminescent Dosimeter)

  • 지의규;박석원;강위생;김일한
    • Radiation Oncology Journal
    • /
    • 제17권4호
    • /
    • pp.321-328
    • /
    • 1999
  • 목적 : 면역억제, 악성림프종 및 백혈병의 치료, 골수이식 등에 적용되는 전신방사선치료에 시행되는 좌우 이문대향조사법의 표면 방사선량 및 중심 방사선량의 균일성을 열형광선량계를 이용하여 확인하고자 하였다. 대상 및 방법 : 1996년 9월부터 1998년 8월까지 좌우 이문대향조사법으로 전신방사선치료를 시행한 10명의 환자 중 매번 방사선량이 측정된 8명의 환자를 대상으로 하였다. 열형광선량계를 사용하여 두부, 경부, 액와부, 대퇴부, 족관절부 등의 표면 선량을 측정하였고 인형 팬톰에서 동일한 조건하에서 두부, 경부, 액와부, 복부, 둔부 등의 표면 선량과 중심 선량을 측정하였다. 결과 : 중심부인 복부 처방 선량을 기준으로 할 때 부위별로 환자의 두부, 경부, 액와부, 대퇴부, 족관절부에서 표면 방사선량은 각각 $98.3{\pm}7.8,{\;} 98.3{\pm}7.5,{\;}95.1{\pm}6.3,{\;}98.3{\pm}5.5,P{\;}95.3{\pm}6.3\%$였다. 인형 팬톰에서 처방 선량에 대하여 두부, 경부, 액와부, 복부 및 둔부에서의 표면 방사선량은 각각 $85.0{\pm}4.0,{\;}86.6{\pm}5.8,{\;}83.9{\pm}4.9,{\;}94.8{\pm}5.3,{\;}94.88{\pm}2.8\%$였고, 중심 방사선량은 각각 $96.6{\pm}2.2,{\;}95.3{\pm}3.2,{\;}80.4{\pm}1.9,{\;}100.0{\pm}3.1,{\;}90.5{\pm}2.2\%$였다. 표면 선량 대비 중심 선량의 비는 두부, 경부, 액와부, 복부 및 둔부에서 각각 $1.14{\pm}0.06,{\;}1.10{\pm}0.09,{\;}0.96{\pm}0.05,{\;}1.06{\pm}0.06,{\;}0.95{\pm}0.02$였다. 인형 팬톰에서 얻은 표면 선량 대비 중심 선량의 비를 이용하여 환자에서의 중심 선량을 계산하였을 때, 두부, 경부, 액와부, 대퇴부, 족관절부에서 각각 $103.4{\pm}9.0,{\;}107.8{\pm}10.5,{\;}91.1{\pm}6.1,{\;}93.8{\pm}4.5,{\;}104.5{\pm}9.3\%$였다. 결론 : 환자에서의 측정된 표면 선량과 계산한 중심 선량의 분포는 $-8.9\~+7.8\%$였으나, 선량 분포가 $+5\%$ 이상 증가 또는 감소된 부위인 경부와 액와부에서는 인형 팬톰과 환자와의 좌우 두께의 차이에 의해서 실제보다 크게 계산되었으므로 실제 환자에서의 전신 선량 분포는 이보다 더 우수할 것으로 생각된다.

  • PDF

두경부 양성자 치료계획 시 MVCT를 이용한 Metal Volume 평가 및 양성자 선량분포 평가 (Evaluation of Metal Volume and Proton Dose Distribution Using MVCT for Head and Neck Proton Treatment Plan)

  • 서성국;권동열;박세준;박용철;최병기
    • 대한방사선치료학회지
    • /
    • 제31권1호
    • /
    • pp.25-32
    • /
    • 2019
  • 목 적: 두경부 방사선 치료 시 Dental Implant에 의한 Metal Artifact로 인해 보철물의 크기, 모양 및 Volume이 달라지고 이로 인해 타겟 및 주변 정상조직에 대한 방사선치료계획의 정확성이 떨어진다. 본 연구는 치아크기를 재현한 Metal을 KVCT, SMART-MAR CT, MVCT를 통해 영상을 획득 하여 Volume을 평가하고 양성자 치료계획에 적용시켜 선량분포의 차이를 분석해 보고자 한다. 대상 및 방법: 치과에서 치료하는 방법을 고려하여 인레이, 크라운, 브릿지와 비슷한 크기의 A보철물($0.5{\times}0.5{\times}0.5cm$), B보철물($1{\times}1{\times}1cm$), C보철물($1{\times}2{\times}1cm$)을 저용융점납합금(Cerrobend, $9.64g/cm^3$) 사용하여 제작하였다. In House Head & Neck Phantom 안에 보철물를 위치시키고 CT Simulator(Discovery CT 590RT, GE, USA)를 이용해 Slice thickness 1.25 mm로 KVCT 영상과 SMART-MAR 영상을 획득하였다. MVCT 영상은 $RADIXACT^{(R)}$ Series(Accuray $Pricision^{(R)}$, USA)을 이용해 동일한 방법으로 획득하였다. MVCT, SMART-MAR CT, KVCT를 통해 획득한 보철물의 형상을 전산화 치료계획장비 Pinnacle(Ver 9.10, Philips, Palo Alto, USA)의 Autocontour Thresholds Raw Values를 통해 X, Y, Z축의 크기 및 Volume을 비교하였다. 양성자 치료계획은 위의 실험에서 얻은 보철물B($1{\times}1{\times}1cm$)의 각 CT별 치아 Contour를 KVCT 상에 fusion하여 양성자 치료계획(Ray station 5.1, RaySearch, USA)을 세우고 선량의 차이를 비교 평가하였다. 결 과: 실측 사이즈 대비 A보철물(MVCT : 1.0배, SMART-MAR CT : 1.84배, KVCT : 1.92배), B보철물(MVCT : 1.02배, SMART-MAR CT : 1.47배, KVCT : 1.82배), C보철물(MVCT : 1.0배, SMART-MAR CT : 1.46배, KVCT : 1.66배)로 각 크기의 보철물에서 MVCT가 가장 실제 Volume과 유사하게 측정되었다. 양성자 치료계획에서 B보철물의 Volume을 각각 적용하여 측정한 결과 $D_{99\%}$ volume의 선량이 기준 3082 CcGE 대비 MVCT:3094 CcGE, SMART-MAR CT:2902 CcGE, KVCT:2880 CcGE로 측정되었다. 결 론: 전체적인 Volume과 X축 Z축의 크기는 MVCT에서 실제 크기와 가장 일치했고 superior-Inferior방향인 Y축은 CT에 따라 차이 없이 길이가 일정했다. 두경부 양성자 치료 시 보철물의 크기, 모양 및 Volume이 비슷한 MVCT에서 가장 실제 값과 비슷한 선량분포를 보였고 MVCT를 이용한 보철물의 contour를 KVCT에 fusion하여 양성자치료계획에 적용 시 매우 유용할 것으로 사료된다.

맥류의 도복에 관여하는 유용형질의 분석에 관한 연구 (Analytical Studies on The Useful Characters Affecting The Lodging Resistance of Wheat and Barley Varieties)

  • 조장환
    • 한국작물학회지
    • /
    • 제11권
    • /
    • pp.105-117
    • /
    • 1972
  • 본연구는 맥류의 도복에 관여하는 주요형질의 상호관계를 구명함과 아울러 주요 대소맥 품종의 내도복성정도를 분류하고, 내도복성 품종 선발의 기준을 인정하여 보고자 한 것이며, 그 결과를 요약하면 다음과 같다. 1. 포장도복과 도복지수는 고도의 정의 상관(대맥 r=0.44-0.67 소맥 r=0.46-0.68)이 있으며 지상부 Bending moment에 간자체의 정도를 가미한 지수로서 도복저항성 검정에 가장 유효하다. 2. 간의 Bending stiffness를 표시하는 좌절시 Bending moment와 단면 2차 moment와는 정의 높은 상관(대백 r=0.59, 소맥 r=0.46-0.53)을 보였다. 3. 간의 Bending stiffness(좌절시 Bending moment 단면 2차 moment)와 간에의 건물집적량을 표시하는 단위간건물중과는 높은 정의 상관 (대맥 r=0.35-1.40, 소맥 r=0.33-0.76)을 보였다. 4. 도복지수와 단위간건물중 (대맥 r=-0.51~-0.70, 소맥 r=-0.65~-0.83) 좌절시 Bending moment (대맥 r=-0.29~-0.69, 소맥 r=-0.54~-0.89)과는 특히 높은 부의 상관을 보였으며, 소맥의 경우는 좌절하중, 단면 2차 moment, 단면계수와는 높은 부의 상관을 보였다. 5. 간외경은 간내경보다 간의 물리적 특성과 상관이 높으며 좌절하중 (대맥 r=0.42-0.56, 소맥 r=0.39-0.44), 좌절시 Bending moment (대맥 r=0.40-0.41, 소맥 r=0.38-0.49), 단면 2차 moment (대맥 r=0.56-0.97, 소맥 r=0.0.28-0.28), 단면계수(소맥 r=0.22-0.96)와는 정의 높은 상관이 있었고, 간벽후와 물리적특성과도 정의 상관을 보였다. 6. 간장은 포장도복과는 품종군에 따라서는 정의 상관은 보이나, 간의 강도를 고려한다면 내도복저항성품종 선발의 지표로서 이용하기는 어려울 것으로 보인다. 7. 대소맥의 많은 품종의 내도복성 정도를 분류한 결과, 한국품종중 대맥은 내도복저항성품종이 많고, 대맥은 내도복성인 품종의 분포가 대맥보다 적었으나, 일본품종들을 대소맥 모두 내도복저항성인 품종이 많았다. 8. 내도복저항성인 품종의 선발을 위하여는 도복지수가 대맥 1.67 소맥 1.76 정도 이하인 것은 고도의 저항성이 있었다.

  • PDF