• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.75-79
• /
• 2003

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. This geometric inaccuracy caused by the welding distortion tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding distortion. The validity of the prediction method must be also clarified through experiments. For the purpose of reducing the weld-induced bending deflection, this paper proposes the plastic counter-deforming method (PCDM) using the line heating as the optimum distortion control method. The validity of this method has been substantiated by a number of numerical simulations and actual measurements.

• 조명전기설비학회논문지
• /
• 제25권10호
• /
• pp.102-108
• /
• 2011

The existing power flow has a single direction to the line end but the bidirectional power flow will possibly occur depending on the output capacity in the 22.9[kV] distribution power system connected with the dispersed generation(DG). So these characteristics would influence the power system management. The DG have many advantages such as assistance source, Load share etc. So the utility must apply the bidirectional protection system so as to maximize an advantage of DG. This paper describes the field test case of bidirectional protective device in order to investigate the device performance when applied to bidirectional power system. We have tested in the power system test site of KEPCO and these tests provide the basis for performance verification test of bidirectional protective device in the power system.

• 제어로봇시스템학회논문지
• /
• 제22권8호
• /
• pp.627-632
• /
• 2016

In this paper, we propose a new vision-based defect inspection system for the surface of hot slabs. To minimize the influence of self-emission from slab surfaces with high temperature, an optic method based on blue LED light and a blue pass filter is proposed. Because the slab surface is partially covered with scales, which are unavoidable oxidized substances caused during manufacturing, it is difficult to distinguish between vertical cracks and scale. In order to resolve this problem and to improve the detection performance, the use of a Gabor filter and dynamic programming are proposed. Finally, the effectiveness of the proposed method is shown by means of experiments conducted on images of hot slabs that were obtained from an actual slab production line.

• Human Ecology Research
• /
• 제54권1호
• /
• pp.97-106
• /
• 2016

The purposes of this study were to examine the effect of consumers brand identification of a luxury fashion brand on brand attachment and to determine the moderating influences of self-monitoring and social self-esteem on this effect. For this study, a questionnaire was developed through a literature search. The developed survey was then conducted by means of on-line and off-line questionnaires. Data from 228 women with experience in buying luxury fashion brands was analyzed with descriptive statistics, Cronbach a, factor analysis, regression, two-way one-way analysis of variance (ANOVA) and t -test using SPSS for Windows 21.0. First, the brand identification of consumer was composed three factors; actual, ideal, social identification. The brand attachment was composed five factors; emotional, dependency, attraction, intellectual curiosity, and general interest. Second, it was shown that brand identification has a positive influence on brand attachment. Third, it was also shown that there is a moderating influence from self-monitoring on the effect of consumer's brand-identification of a luxury fashion brand on brand attachment. Interaction effect between consumer's brand-identification and self-monitoring was found out to be meaningful at brand affect. Fourth, there was an additional moderating effect from social self-esteem on this effect. Interaction effect between consumer's brand-identification and social self-esteem was found out to be meaningful at brand affect.

• 한국콘텐츠학회논문지
• /
• 제8권1호
• /
• pp.27-38
• /
• 2008

정보 기술의 급격한 발달로 인해 다양한 상품과 서비스가 출시되고 있다. 하지만 지속적으로 사용을 계속하는 상품이나 서비스는 많지 않은 것이 현실이다. 새로운 사용자를 유치하는 것보다 기존 사용자를 지속시키는 것은 기업의 효율적인 측면에서 매우 중요하다. 하지만, 기존의 정보 기술과 관련한 연구들은 새로운 사용자를 유치하는데 초점이 맞추어져 왔다. 따라서 기존 사용자를 지속적으로 유지하기 위한 연구는 매우 미미한 실정이다. 본 연구에서는 모바일 웹 사용자를 대상으로 모바일 웹의 지속적 사용을 위한 지속 사용 모델을 개발하였고, 이러한 지속 사용 행동이 실제 사용량에 어떠한 영향을 끼쳤는지 파악하고자 하였다. 이를 위해 모바일 웹의 지속적 사용에 중요한 영향을 끼치는 요인을 발굴하였고, 이를 실증적으로 검증하고자 하였다. 연구 결과, 사후 기대인 사후 유용성, 사후 사용 편의성, 사후 즐거움, 사후 지각된 가치가 사용자의 만족, 사용 지속의도에 유의하게 영향을 끼쳤으며, 사용자의 사용지속의도 역시 모바일 웹의 실 사용량에 유의하게 영향을 끼쳤다. 본 연구 결과와 더불어, 만족과 사용 지속의도에 중요하게 끼치는 영향은 서로 다르게 나타나 만족과 사용 지속의도를 높이는 전략이 서로 다르게 해야 함을 시사하고 있다. 마지막으로 본 연구는 연구의 한계점과 실증적 시사점에 대하여 제시하고 있다.

• 한국철도학회논문집
• /
• 제12권6호
• /
• pp.983-988
• /
• 2009

기존선 속도향상 시에 주행안전성을 고려한 기존선 구간별 최대 운행가능속도에 대한 실용적인 기준 을 제시하여 기존선의 곡선부 및 완화곡선부 통과 시 속도를 향상시켜야 한다. 본 연구에서는 탈선의 위험도가 높은 곡선부 통과하는 열차의 고속향상을 도모하기 위하여 실제 선로조건인 남성현-청도 상 하행 구간에서의 곡선부 구간별 통과시 주행안전성에 미치는 영향을 살펴보았다. 곡선반경별 주행속도를 실제 선로 조건에서의 기존 속도 대비 5-20% 향상시켜 주행안전성 해석을 수행하였다. 주행안전성 해석 결과, 기존 주행속도 대비 약 15% 이하의 속도조건에서는 탈선 계수와 윤중감소율이 허용기준 이내로 나타나 남성현-청도 상 하행 전 구간 내에서 속도 향상의 가능성을 확인할 수 있었다.

• 한국농공학회지
• /
• 제18권2호
• /
• pp.4089-4095
• /
• 1976

The safety of shore structure including the sea dipe is largely affected by typhoon. Accordingly it is desirable to analize the typhoon and determine the wind direction and velocity for use in planning and design of the structure. This method was adopted for the design of the Yong San Gang Estuary Dam. A comparative study of the results of typhoon analysis with the meteorological data obtained through actual observation is summarized as follows; (1) 62% of the typhoons occur during May to June in a year, and 62% of the typhoons which have an influence on the Korean peninsula, especially the proposed estuary dam fsite, proceed eastward through the zone in lat. 36$^{\circ}$-37$^{\circ}$N. Such typhoons occur two to three times a year on the average. (2) Data on typhoon "SARL" were used as a model case in designing the estuary dam, where it was proved that a southwesterly wind had a maximum velocity of 30m/sec in case r=150km, ${\alpha}$=120$^{\circ}$. Within the range of 22$^{\circ}$30'on the right and left side of the fetch line of the estuary dam, the wind direction varied SSW\longrightarrowSW\longrightarrowWSW, and the wind velocity varied 29m/sec\longrightarrow30m/sec\longrightarrow125m/sec. Such phenomemum lasted for five hours. (3) An analysis of data obtained during 44 years at Mok Po Meteorological Station shows that a wind with a velocity of some 25m/sec occurred twelve times in the S-direction and two times in the SW-direction, while that with a velocity of 30m/sec occurred three times in the S-direction, three times in the SSW-direction and one time in the SW-direction. The wind which had an influence on the estuary dam had a direction of SSW\longrightarrowSW\longrightarrowWSW and a velocity of min. 30m/sec. Actually, a wind with a max. velocity of 31.3m/sec occurred in the SSW-direction on March 15 and 16, 1956 where the mean velocity during two hours was 28m/sec and that during four hours was 24.6m/sec. (4) The data obtained through actual observation show that when the velocity is low, the wind with a fixed direction lasts long, and when the velocity is high, it is short-lived. It is difficult to determine the velocity of a wind which blows in a fixed direction for consecutive two or four hours. Therefore, the values obtained through typhoon analysis are larger that those obtained through actual observation, and hence, it is resonable to use the analyzed valuse for design of the estuary dam and shore structures. (5) The greatest effect was had on the estuary dam when typhoon was proceeding at a velocity of 29.71m/sec in the direction of ${\alpha}$=120$^{\circ}$(SW) at a point of R=150km from the center of the typhoon.

• 한국해양공학회지
• /
• 제21권3호
• /
• pp.46-51
• /
• 2007

A multi-purpose environmental monitoring system has been developed as a commercially available standard using the technique of hetero-core spliced fiber optic sensors, for the purposes of monitoring large-scale structures and preserving natural environments. The monitoring system has been tested and evaluated in a possible outdoor condition, in view of the full-scale operation at actual sites to be monitored. Additionally, the developed system in this work conveniently provides us with various options of sensor modules intended for monitoring such physical quantities as displacement, distortion, pressure, binary states, and liquid adhesion. Two channels of optical fiber line were monitored in each channel, three displacement sensor modules were connected in series, in order to examine the performance to a pseudo-cracking experiment in the outdoor situation and to clarify temperature influences an the system, in terms of the coupling of optical connectors and the OTDR stability. The results from the pseudo-cracking experiment agreed with the actual cracks, by means of calculation, based an the detected displacement values and their geometrical arrangement of the used sensor modules. The temperature change, ranging from 10 to $20^{\circ}C$ resulting from the 10-days free running operation, was found to influence the system stability of ${\pm}10{\mu}m$, primarily due to the coupling instability of the used optical connectors. It was found that fusion splicing, rather than the use of connectors, reduced the fluctuation dawn to ${\pm}2{\mu}m$. The specification and performance of various option modules have been demonstrated to show the capability of inspecting various physical quantities by use of the single system, which would be suitable for multi-purpose environmental monitoring.

• 한국산업융합학회 논문집
• /
• 제27권3호
• /
• pp.629-634
• /
• 2024

The Korea Research Institute of Ships and Ocean Engineering (KRISO) has developed a test module that can vertically ascend and descend with a buoyancy engine to verify the performance of the developed buoyancy engine. The independent test module has been tested in the Ocean Engineering Basin(C.M.Lee et al., 2023). After that, more tests were performed in the Deep Ocean Engineering Basin and at sea. In the 50-meter depth pit test of the Deep Ocean Engineering Basin, there were no problems with the ascent and descent operations, but the buoyancy engine was not properly maintained due to various problems in the independent test module, resulting in a difference between the calculated results using the solution of the equations of motion and the actual measurement results. The East Sea test was conducted at a depth of approximately 110 meters north-east of Pohang, with a dive to 100 meters. The difference between the pressure sensor value and the calculated value was observed, but after checking the results of the underwater position tracking device(USBL, Ultra Short Base Line system), it was estimated that the difference was caused by the influence of the current.

• 대한토목학회논문집
• /
• 제30권1D호
• /
• pp.27-36
• /
• 2010

근래 도시철도의 운영비와 건설비의 증가로 인하여 대도시에서의 도시철도사업 운영은 많은 어려움을 겪고 있는 실정이다. 특히 부산도시철도의 당면 문제점인 이용 승객의 감소추세와 이용효율의 저하를 개선하고자 도시철도 중심의 환승체계의 구축이 요구되어지고 있다. 이러한 문제를 해결하기 위해 양산 지역내 부산도시철도 1호선과 2호선을 연결시키는 환승체계 구축의 필요성이 제기되었다. 따라서 양산시와 부산시와의 활발한 이동량과 사송지구 택지개발사업의 시행, 부산 도시철도 2호선 양산선 개통 등으로 양산시와 부산 도시철도 1호선과의 연결을 통한 도시철도망 환승체계 구축 필요성이 크게 대두됨에 따라, 부산 도시철도 1호선 양산선(노포~양산역~북정) 연장에 따른 도시철도 환승체계 구축 방안은 다방천변으로 건설하는 노선1을 최적노선 대안으로 선정함으로서 지역주민의 편리한 이용과 경제성은 물론 지역발전의 원동력이 될 수 있을 것으로 기대된다. 특히 2개 노선을 4가지 방법에 의한 경제성 분석 결과 노선1의 건설에 필요한 총 사업비는 단선 건설시 4,827.1억원으로 산정되었으며, 사업비중 순 공사비가 가장 많은 비용을 차지하고 있고, 다음으로 차량구입비, 예비비, 용지보상비, 부대비 순으로 나타났으며, 노선1 단선건설시 경제성 분석결과 편익/비용비(B/C)가 1.013, 순현재가치(NPV)가 72.7억원, 내부수익율(IRR)이 5.614%로 분석되어 경제성이 있는 것으로 평가되었다.