• Journal of the Korean Society of Safety
• /
• v.7 no.4
• /
• pp.7-12
• /
• 1992

The smouldering combustibility of cellulose insulation treated with boric acid-borax-aluminium sulfate as combustion retardants are examined by cigarette ignition method and electrical cardrige heater method. The effectiveness of Aluminium sulfate as a third combustion are acceptable both smouldering resistance and flame resistance at 18% level of all examined formulation. As the proportion of Aluminium sulfate in the formulation was increased, the flame resistance of cellulose insulation was improved.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.13-21
• /
• 2004

The deposition rate, the current efficiency and surface morphology of trivalent Cr deposits were investigated according to additives in sulfate bath and current density. The deposition rate of the Cr deposits plated from the formic acid complexed bath was noticeably higher than that of the glycine complexed bath. The current efficiency of the deposition from formic acid bath was higher than that of the glycine bath and increased with current density in the range of 20-50 A/d$\m^2$. The current efficiency of the deposition from the formic acid bath with boric acid buffer was higher than that of the bath with aluminum sulfate or boric acid-aluminum sulfate buffers. The nodular crystallite size of the Cr deposits increased with current density and the uniform and crack-free growth of the deposits for the aluminum sulfate was observed compared to the other buffers.

• The korean journal of orthodontics
• /
• v.28 no.5 s.70
• /
• pp.877-891
• /
• 1998

This study was designed to observe the effects of various concentration of polyacrylic acid containing different concentration of sulfate ion on the crystal formation on the enamel surface. Experimental crystal growth solutions were made of $10\%,\;20\%,\;30\%\;and\;40\%$ polyacrylic acid(molecular weight,5,000) solutions which containing 0.1M, 0.2M, 0.3M, 0.5M, and 1.0M sulfate ion respectively. The extracted human first bicuspid enamel surface was contacted for n seconds with these solutions, washed for 15 seconds, dried, and then the crystal topography on the enamel surface was observed under the scanning electron microscope. The crystal topography were evaluated on the SEM photographs by degree of crystal coverage, crystal length, and consistency of crystal morphology, and conclusions were as the follows. 1. Polyacrylic acid solution etched slightly the enamel surface, and the difference of etching effect by its concentration was not observed. 2. The effect of concentration of polyacrylic acid on the crystal formation was less, especially that of $20\%\~40\%$ polyacrylic acid was almost not different. 3. Concentration of the sulfate ion was a determinant factor in precipitating crystals on the enamel. The experimental crystal growth solutions containing 0.1 M sulfate ion did not make crystal formation but those containing over 0.2 M sulfate ion did. 4. The degree of crystal coverage showed a tendency to increase and then decrease according to the concentration of sulfate ion in the $20\%-40\%$ polyacrylic acid. The experimental solutions containing 0.5 M sulfate ion showed the peak of degree of crystal coverage. 5. The crystal length showed a tendency to decrease by increment of sulfate ion in the polyacrylic acid solution. 6. There was a tendency to increase the frequency of random arragement of short crystals when increasing the concentration of sulfate ion in the polyacrylic acid solution. The lower concentration of sulfate ion in the polyacrylic acid solutions tended to make spherulitic arrangement of crystals, the higher concentration of sulfate ion, the more random arrangement of crystals. The experimental solutions containing 0.5M sulfate ion showed more spherulitic arrangement than random arrangement of crystals. 7. The best one of these experimental crystal growth solutions was $30\%$ polyacrylic acid solution containing 0.5M sulfate ion.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.E1
• /
• pp.1-12
• /
• 2002

One technique for determining dry acid deposition fluxes involves measurement of time - averaged ambient concentrations of dry acid deposition species using filter packs (FP) coupled with estimates of mean deposition velocities for the exposure period. A critical problem associated with filter pack data comparisons between various field sampling networks is the use of diverse sampling flow rates and duration protocols. Field experiments were conducted to evaluate the effects of varying sampling flow rates, from 1.5 to 10 standard liters per minute, on total nitrate and sulfate measurements of specific dry acid deposition species . Collocated FP samplers were used to determine sampling and analysis data reproducibility and representativeness . Ambient air samples were simultaneously collected using groups of filter packs operated at various flow rates over identical 7 day periods. The species measured were sulfur dioxide, particulate sulfate , nitric acid and particulate nitrate. Statistical results (ANOVA; alpha level 5%) showed that neither the low nor high sampling flow rates caused a significant difference in the measurements of total sulfate and adjusted total nitrate (ATN) . However, it was concluded that for high flow rate sampling measurements, total nitrate (TN) could be affected during extended sampling durations because of potential nitric acid overloading and breakthrough. Although the previous workers (Costello, 1990; Quillian, 1990) used much higher sampling flow rates (~ 17 sLpm) than employed here, it was assumed that for a high loading (> 50$\mu\textrm{g}$ HNO$_3$) of nitric acid on the Nylon filters, a significant fraction (~10%) of nitric acid could pass through the Nylon filters and be collected on the carbonate impregnated filters. It was concluded that even at the highest sampling flow rate employed (10 sLpm) at the Cary Forest site, nitric acid breakthrough was less than 10% of the total HNO$_3$ collected. However, for a heavily polluted urban airshed or with longer sampling times , higher filter loadings could result in substantial nitric acid breakthrough and HNO$_3$concentrations would be underestimated.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2005

The feasibility of producing sulfuric acid and ammonia water from ammonium sulfate was investigated by an integrated process including ammonia stripping (AS) and electrodialysis with bipolar membrane (EDBM). It was suggested that the production of sulfuric acid using ammonia stripping-electrodialysis with bipolar membrane (ASEDBM) was effective in obtaining high concentration of sulfuric acid compared with EDBM alone. AS was carried out over pH 11 and within the range of temperatures, $20^{\circ}C{\~}60^{\circ}C$. Sodium sulfate obtained using AS was used as the feed solution of EDBM. The recovery of ammonia increased from $40\%$ to $80\%$ at $60^{\circ}C$ due to the increased mobility of ammonium ion. A pilot-scale EDBM system, which is composed of two compartments and 10 cell pairs with an effective membrane area of $200 cm^2$ per cell, was used for the recovery of sulfuric acid. The performance was examined in the range of 0.1 M${\~}$1.0 M concentration of concentrate compartment and of $25 mA/cm^2{\~}62.5 mA/cm^2$ of current density. The maximum current efficiency of $64.9\%$ was obtained at 0.1 M sulfuric acid because the diffusion rate at the anion exchange membrane decreased as the sulfuric acid of the concentrate compartment decreased. It was possible to obtain the 2.5 M of sulfuric acid in the $62.5 mA/cm^2$ with a power consumption of 13.0 kWh/ton, while the concentration of sulfuric acid was proportional to the current density below the limiting current density (LCD). Thus, the integrating process of AS-EDBM enables to recover sulfuric acid from the wastewaters containing ammonium sulfate.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.1
• /
• pp.131-142
• /
• 2004

When the cotton/polyester fiber mixed fabrics were treated with ferrous sulfate and oxalic acid for burn out finishing, it was examined how the effects of process conditions as concentration of burn out agents, temperature, time and pressure act onto the properties of polyester ground fabrics. The results are as follows. The effect of burn out finishing by pressure was greated in 3 kgf/$\textrm{cm}^2$. The properties as white index and tensile strength of polyester ground fabrics were decreased according as processing concentration, temperature time increases. The shrinkage was increased according as processing concentration, temperature time increases. The optimum condition of burn out agents to ferrous sulfate was 30% concentration, 150$^{\circ}C$, 1 min, 3 kgf/$\textrm{cm}^2$ and to oxalic acid was 10% concentration, 110$^{\circ}C$, 1min, 3 kgf/$\textrm{cm}^2$. And the optimum of ferrous sulfate and oxalic acid used in combination was 10% ferrous sulfate and 7% oxalic acid, 110$^{\circ}C$, 1 min., 3 kgf/$\textrm{cm}^2$.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.559-562
• /
• 2003

The results and discussions of surveyed case site at constructed steel pile in potential acid sulfate soil were as follows. Topography at surveyed site was local alluvial valley and that site soils was classified as BanGog and YuGye series as detailed soil surveyed results in RDA and soil texture was Clay/Clay Loam. Soils pH was neutral, which was average 7.5 but much decreased to average 4.2 after $H_2O_2$ treatment. Organic matter and sulfate ions contents were very rich. The corrosion was severe at ground water fluctuation depth. Deposits colored black were attached to steel pile surface, which because of violent reaction in treatment HCI solution, were guessed as corrosion products (FeS) reduced by sulfate reducing bacteria(SRB). Consequently, main cause was thought microbiologically induced corrosion at this site where there is ground water fluctuation occurring oxidation and reduction reactions in turn and the soil is potential acid sulfate soil.

• The International Journal of Costume Culture
• /
• v.6 no.1
• /
• pp.11-18
• /
• 2003

Agricultural drainage salt generated during irrigation of crops in San Joaquin Valley, California, exceeds 600,000 tons annually and cumulates in the field in a rapid rate. As a result, the waste is taking out more farmlands for salt storage and disposal, imposing serious concerns to environment and local agricultural industry. In searching for a potential solution to reduce or eliminate the waste, this research explored feasibility of producing a value-added product, sodium sulfate, from the waste and utilizing the product in textile dyeing. The results indicated that sodium sulfate could be produced from the salt and could be purified by a recrystallization method in a temperature range within the highest and lowest daily temperatures in summer in the valley. The recovered sodium sulfate samples, with purities ranging from 67% to 99.91, were compared with commercially available sodium sulfate in the dyeing of levelling dyes. In nylon fabrics, the salt samples had little color difference in the dyeing with C.I. Acid Yellow 23 and C.I. Acid Blue 158. All salt samples' gray scale was 5 grade. In wool fabrics, the salt samples had little color difference in dyeing with C.I. Acid Yellow 23 and C.I. Arid Blue 158. All salt samples' gray scale was 5 grade. Generally, the dyeing of levelling dyes using recovered salts from farm drainage had little color difference than the dyeing of levelling dyes using commercial sodium sulfate.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.1
• /
• pp.72-80
• /
• 1997

To elucidate food value and medicinal effect of sea cucumbers, sugar composition of those gly-coprotein and chondroitin sulfate was studied. The contents of sulfate esters in sea cucumbers were 1.21%(blue), 0.90%(red) and 1.19%(black). Predominant carbohydrates were identified as fucose, glucose, D-mannuronic acid and N-acetylglucosamine, and those amount was more than 80% to total carbo-hydrate, while the minor sugar composition was ribose, mannose, galactose, N-acetylgalactosamine and D-glucuronic acid. Also, the major carbohydrate moiety of glycoproteins of sea cucumbers was revealed as fucose, mannose, N-acetylglucosamine, glucose and ribose, and those amount was more than 86% to total carbohydrate. Galactose, N-acetylgalactosamine, D-glucuronic acid and mannuronic acid were minor carbohydrate moiety. The contents of sulfate esters in glycoproteins were 0.96% for blue sea cucumber, 1.15% for red sea cucumber and 1.13% for black sea cucumber, while those in chondroitin sulfates were 3.52%(blue), 3.60%(red) and 3.72%(black). The carbohydrate moiety of chondroitin sulfate was identified as N-acetylgalactosamine (73~ 87%), fucose (7~15%) and D-glucuronic acid(5~12%). As the base on the IR spectrum of strong absorption appeared in 1240$cm^{-1}$ / for stretching vibrations in S=0 group and weak absorptions in 850$cm^{-1}$ / and 820$cm^{-1}$ /for stretching vibrations in C-0-S group, chondroitin sulfates had sulfate group which was bound to $C_4$in fucose.

• KSBB Journal
• /
• v.21 no.6 s.101
• /
• pp.418-421
• /
• 2006

Fatty acid methyl esters, also referred to as biodiesel, have been determined to have a great deal of potential as substitutes for petro-diesel. In order to enhance productivity in the biodiesel production process, feedstocks were previously recommended to be anhydrous, with a free fatty acid content of less than 0.5%. In this study, the effects of several catalysts, methanol molar ratio, catalyst amount, and reaction time on the reduction of free fatty acid level were studied with a simulated feedstock consisting of 20% oleic acid in rapeseed oil. Ferric sulfate was selected as the best catalyst. Increasing the catalyst amount and methanol molar ratio is very effective in decreasing the acid value of the simulated mixture. Our results may provide useful information with regard to the development of more economic and efficient free fatty acid removal system.