• Advances in materials Research
• /
• v.3 no.3
• /
• pp.163-174
• /
• 2014

In this study, fatigue properties and crack growth characteristics of a polycarbonate (PC) were examined during cyclic loading at various mean stress (${\sigma}_{amp}$) and stress amplitude (${\sigma}_{mean}$) conditions. Different S vs. N and da/dN vs. ${\Delta}K$ relations were obtained depending on the loading condition. The higher fatigue strength and the higher resistance of crack growth are seen for the PC samples cyclically loaded at the higher mean stress and lower stress amplitude due to the low crack driving force. Non-linear S - N relationship was detected in the examination of the fatigue properties with changing the mean stress. This is attributed to the different crack growth rate (longer fatigue life): the sample loaded at the high mean stress with lower stress amplitude. Even if the higher stress amplitude, the low fatigue properties are obtained for the sample loaded at the higher mean stress. This was due to the accumulated strain energy to the sample, where severe plastic deformation occurs instead of crack growth (plasticity-induced crack closure). Shear bands and discontinuous crack growth band (DGB) are observed clearly on the fracture surfaces of the sample cyclically loaded at the high stress amplitude, where the lower the ${\sigma}_{mean}$, the narrower the shear band and DGB. On the other hand, final fracture occurred instantly immediately after the short crack growth occurs in the PC sample loaded at the high mean with the low ${\sigma}_{amp}$, i.e., tear fracture, in which the shear bands and DGB are not seen clearly.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.369-375
• /
• 2009

The Periodic replacements criterion of rail is calculated on the basis of the research result of RTRI in Japan. It is suggested that the service life of the continuous welded rail(CWR) is estimated by the relationship between the rail surface irregularity according to the accumulated passing tonnage and bending fatigue of welded part in CWR. In order to establish the periodic replacements criterion of CWR, this study measured the rail surface irregularity according to the accumulated passing tonnage, the types of track system and welding. Therefore, it is analyzed that the gas pressure welding is the worst one of the others. In addition, it is analyzed that the rail surface irregularity growth rate in ballast track is about $0.02{\sim}0.03mm$/100MGT and its in concrete track is about $0.005{\sim}0.02mm$/100MGT Finally, the result of this study is able to use the basis data to establishing the periodic replacements criterion of CWR considering rail grinding.

• Journal of the Korean Society for Railway
• /
• v.17 no.3
• /
• pp.193-200
• /
• 2014

In this study, fatigue tests on existing continuous welded rail (CWR) on a concrete track were carried out. Based on the test results, a S-N curve expressing the remaining life of the CWR at a fracture probability of 50% was obtained using weighted probit analysis suitable for small-sample fatigue data sets. As rails had different histories in terms of accumulated passing tonnage, the test data were corrected to average out the accumulated passing tonnage. The remaining service life for the CWR on the concrete track in an urban railway was estimated using the prediction equation for the bending stress of rail developed in the past to estimate rail base bending stress and taking the surface irregularities into consideration. Estimating the remaining service life of the CWR in an urban railway showed that the rail replacement period could be extended over 200MGT. In addition, comparing the concrete track to the ballast track, the fatigue life of rail was analyzed as approximately 300MGT higher than. Therefore, the rail replacement criteria needs to distinguish between the ballast track and the concrete track, and not the criteria needs to be changed as a target for the maintenance, although it is necessary to remove longitudinal rail surface irregularities at welds by grinding.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.723-730
• /
• 2008

Due to the higher ratio of live load to total loads of railway bridges, the accumulated damage by cyclic fatigue is significant. Moreover, it is highly possible that the initiated crack grows faster than that of highway bridges. Therefore, it is strongly needed to assess the safety for the accumulated damage analytically. The initiation and growth of fatigue-crack are related with the stress range, number of cycles, and the stiffness of the structural system. The stiffness of the structural system includes uncertainties of the planning, design, construction and maintenance, which varies as time goes. In this study, the authors developed the design and risk assessment techniques based on the reliability theories considering the uncertainties in load and resistance. For the probabilistic risk assessment of crack growth and the remaining life of the structures by the cyclic load of railway and subway bridges, response surface method (RSM) combined with first order second moment method were used. For composing limit state function, the stress range, stress intensity factor and the remaining life were selected as input important random variables to the RSM program. The probabilities of failure and the reliability indices of fatigue life for the considered specimen under cyclic loads were evaluated and discussed.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.350-358
• /
• 2012

This paper deals with accuracy of accumulated fatigue damage estimation using stochastic fatigue analysis method based on Rayleigh PDF. From full scale measurement data on an 8100TEU container vessel, zero-order spectral moments for wave- and vibration-induced energy spectral densities are determined on the probability level of 99%. 80 simulation cases in total are prepared according to the variation of ratio of zero-order spectral moments and center frequency of vibration ESD. By using inverse Fourier transformation and rainflow cycle counting for the combined ESD of wave and vibration, exact fatigue damages are derived. Fatigue damages in frequency domain based on Rayleigh PDF show large conservativeness compared to exact fatigue damages in times domain. The main cause of the excessive conservativeness is analyzed by two aspects: ratio of zero crossing and peak frequencies and ratio of initial zero order spectral moments and zero order spectral moments from rainflow stress range distributions. Finally, a guideline of applicability of Rayleigh PDF is proposed for wide band processes.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.359-366
• /
• 2012

This is the final one of the two companion papers dealing with accuracy of accumulated fatigue damage estimation under wide band process. It is stated that four kinds of wide band models exist: typed of equivalent stress, combined PDF, correction factor, and damage combination. For the idealized ESDs from full scale measurement data on an 8100TEU container vessel, fatigue damages are compared for a narrow band prediction model based on Rayleigh PDF and five wide band fatigue prediction models of Dirlik, Wirsching-Light, Jiao-Moan, Benasciutti and DNV. DNV model consistently overestimates fatigue damages regardless of variation of ESDs. Predictions by Jiao-Moan model, which is understood as standard method for design of offshore platforms, are also in conservative side. Best accuracy is found from the results by Dirlik and Benasciutti models, but Benasciutti model is preferred since it can easily combined with narrow band fatigue damage based on Rayleigh PDF.

• The Korean Journal of Emergency Medical Services
• /
• v.12 no.3
• /
• pp.71-86
• /
• 2008

Purpose : This study was to examine the influence of job stress of 119 Emergency Medical Technician on fatigue and job satisfaction. Methods : Subjects of this study were 228 Emergency Medical Technicians who worked at 119 Safety Center of total 92 fire stations in 12 cities of Gyeonggido including U, N, H, B, A, S, Y, G, G, G, P and I and the period of data collection was from July 11 to Sep. 10, 2007. Collected data were analyzed with SPSS 14.0 version. Results : Conclusions of this study were as follows. 1) Factor related to organization among job stress factors had the greatest influence on fatigue (B = 0.334, p < 0.01), followed by crisis situation factor (B = 0.2042, p < 0.01), inappropriate treatment factor (B = 0.174, p < 0.05), role conflict factor as special job (B = 0.109, p < 0.05) and professional knowledge and technique factor (B = 0.109, p < 0.05), and the influence of job stress factors on fatigue was explained as $R^2=0.340$. 2) Mental burden factor of job stress factors had the greatest influence on job satisfaction (B = -0.606, p < 0.01), followed by organization factor (B = -0.473, p < 0.01) and interpersonal relation and conflict factor (B = -0.339, p < 0.01), and the influence of job stress factor on fatigue was explained as $R^2=0.308$. Conclusions : Job stress of 119 rescuer is increasing continuously and such an accumulated stress lowers the job efficiency. In order to reduce, job stress, it is important to extend(${\rightarrow}$ have) proper self-development, maintain close relationships and mutual correlations among members of organization in personal dimension and to solve the role conflicts, define the organizational roles and simplify excessive job description into concrete work.

• Restorative Dentistry and Endodontics
• /
• v.37 no.2
• /
• pp.74-78
• /
• 2012

Objectives: This study aimed to evaluate the relationship between the cyclic fatigue of a K3 file and internal stress intentionally induced until the activation of the autostop function of the torque-controlled motor. Materials and Methods: K3 (Sybron Endo) .04 and .06 taper, size 25, 30, 35, 40 and 45 were used in this study. To give the internal stress, the K3 files were put into the .02 taper Endo-Training-Bloc (Dentsply Maillefer) until the activation of the auto-stop function of the torque-controlled motor. The rotation speed was 300 rpm and torque value was 1.0 $N{\cdot}cm$. K3 were grouped by the number of induced internal stress and randomly distributed to 4 experimental groups (n = 10, Stress 0 [control], Stress 1, Stress 2 and Stress 3). For measuring the cyclic fatigue failure, the K3 files were worked against a sloped glass block and time for file separation was recorded. Data was statistically analyzed Statistical analyses were performed using two-way ANOVA and Duncan post-hoc test at p < 0.05 level. Results: Except .04 taper size 30 in Stress 1 group, there were statistically significant differences in time for file separation between control and all experimental groups. K3 with .04 taper showed higher cyclic fatigue resistance than those of .06 taper. Conclusion: In the limitation of this study, the cyclic fatigue of the K3 file was influenced by the accumulated internal stress from use until the auto-stop function was activated by the torque-controlled motor. Therefore, clinicians should avoid the reuse of the K3 file that has undergone auto-stops.

• Journal of Industrial Technology
• /
• v.9
• /
• pp.21-28
• /
• 1989

For the study of the fatigue behavior, high-strength bolted connections on a small scale were manufactured, and carried on fatigue tests. Its experimental values were analysed by stress-fatigue life (S-N) curve. Three types of specimens : the base metal, the cireular hole and the welded sperimens had same net section were made. Through the same tests those experimental values were compared with those of the high-strength bolted conneetions. The results of these studies are as followings. It was found that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the high-strength bolted conneetions were much more about 14% and 16% than that of the base metal specimen. It was thought that this trend was due to frictional force increasing fatigue strength. It was known that fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the welded joints were less 29% and 21% than that of base metal specimen. It was thought that that trend was due to weld flaw. It was appeared that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the high-strength bolted connections were much more about 38% and 30% than that of welded joint. It was thought that it was due to both frictional force increasing the fatigue strength in bolted connections and weld flaw decreasing the fatigue strength in welded connections. It was found that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the B3 specimens were much more 2% and -2% than that of the B4 specimen. It was thought that that trend was due to the frictional force, which concerned with shape of specimen. It was known that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the specimen with circular hole was less 61% and 65% than that of base metal. It was known that the allowable stress for bolted joint was higher than that of welded Joints. If that research is continued and more data are accumulated it can be expected that a basic pattern to provided the indicator of the fatigue design of the bolted connections of steel structures and persume the safety and lifeproof of existing structures is given.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.4
• /
• pp.399-405
• /
• 2004

Currently, the use of carbon steel in a high temperature environment, such atomic reactor, increases. Test piece was heated in electric furnace and the prescribed temperature was controlled within ${\pm}1^{\circ}C$. Debris that falls apart from cracked section due to friction is accumulated inside. Then, as it causes fretting corrosion (formation of oxide layer), it contributes to crack closure.