• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.169-173
• /
• 2011

Crash box is introduced to vehicle design to improve the impact performance and reduce the damage of vehicle body at impact speed. The crash box behind bumper can absorb impact energy effectively to improve vehicle safety. Repair cost at collision accident can be cut down by use of this box. The configuration of car body must be designed by considering the characteristic of material due to the deformation of car body happened at impact. Many papers have been published about material of crash box all over the world. The study of crash box with tube expansion type has been going on Korea. This study is done by the simulation analysis about front collisions against 5 kinds of aluminum crash boxes with the basic structure of square section.

• Bulletin of the Korean Chemical Society
• /
• 제31권1호
• /
• pp.41-46
• /
• 2010

In this work, we report on the characterization of six low-$T_g$ poly[methyl-3-(9-carbazolyl) propylsiloxane] based photorefractive (PR) composites sensitized with poly(3-hexylthiophene) (P3HT) in different concentrations, ranging from 0.2 to 1 wt %. At 632.8 nm, photoconductivity, space charge field, refractive index modulation, and grating buildup time were measured versus external electric field. The photoconductivity was strongly dependent on the visible light absorption and mobility. The magnitude of space charge field was affected by the conductivity contrast $\sigma_{ph}/(\sigma_{ph}+\sigma_d)$. The refractive index modulation increased with the magnitude of space charge field and the PR grating buildup speed increased with the photoconductivity.

• ETRI Journal
• /
• 제13권4호
• /
• pp.52-57
• /
• 1991

We fabricated very high. speed PIN Photodiode module for the application of high speed optical receiver. OMVPE was used for the growth of InP layer on InGaAs absorption layer. The structure was the combination of mesa and planartype. Fabrication procedure was more complicated than simple mesa or simple planar type structure because we used semiinsulating InP substrate in order to reduce stray capacitance. The results at-5V were as follows : dark current was less than 1nA, capacitance was 0.55pF, and cutoff frequency was above 3GHz, and rise and fall time was about 100ps.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권6호
• /
• pp.548-554
• /
• 1997

We fabricated the sample of ultra thin lipid membrane(L-$\alpha$-DLPC) by LB method. The $\pi$-A isotherm of the DLPC was measured at the air-water interface varying with the compressing speed and amounts of solutions for spreading. For the good property of lipid monolayer film, it was necessary to prepare at the lower speed of compressing, with an appropriate volume of solutions for spreading. Absorption, transmitance and intensity with the UV spectrophotometer were measured. The Z-type multilayers showed good characteristics better than Y-type. So we found building-up of structurally high quality LB films is essential to study properties of the films and to get reproducible data.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.109-115
• /
• 1997

Laser cladding is a technique for modification of metal surface. In this laser cladding experiment a metal powder feeding system was developed for more efficient laser cladding. This system can reduce processing time and be used simpler than the conventional method. The feeding of metal powder has given a rise to the process for sequential buildup of bulk rapidly solidified materials in the form of fine powder stream to the laser cladding process. The parameters of laser cladding have been investigated using this experimental equipment. Bronze on aluminum alloy and copper on aluminum alloy were experimented by using defocused beam, powder feeding system, and gas shielding. Good cladding was achieved in the range of beam travel speed of 2.25m/min. In the case of copper/aluminum and bronze/aluminum substrate, the absorption of laser beam was too high to produce low diluted clad. In the case of copper/1050 aluminum, the optimal laser cladding condition was of laser power of 2.8kW, powder feed rate of 0.31g/s and beam travel speed of 2.25m/min. In the case of bronze/aluminum the optimal condition is of laser power of 2.5kW, powder feed rate of 0.31g/s, and beam travel speed of 2.36m/min.

• 한국통신학회논문지
• /
• 제29권2B호
• /
• pp.151-157
• /
• 2004

본 논문은 밀리미터파 대역용 무선통신송수신기를 이용하여 도시환경에 적합한 초고속무선통신 셀백본망을 구축하는 것에 관한 것이다. 밀리미터파 대역중 산소분자의 신호흡수 특성이 큰 60㎓ 대역용 무선통신송수신기를 제작하였으며, 이를 이용한 통신시스템간의 간섭신호가 제거되고 망구성의 형태에 따른 다양한 무선링크의 유효거리를 확보할 수 있음을 확인하였다. 또한 무선백본노드를 중심으로 유효반경 약 500m에서 3km이내의 셀간격으로 각각의 서비스망을 구축하여 도시전체를 셀망의 무선백본망을 구성하고, 155.52MbpsATM(OC-3)급의 도시형 무선 통신 셀백본망이 가능토록 하였다.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.568-573
• /
• 2007

For the manufacturing lightweight fine aggregate, clay and waste material was formed by pelletizer. The fine aggregate of 1-5 mm diameter was formed by diameter 76 cm pelletizer disc. Pelletization variables were : (1) pelletizer disc angle, (2) speed of revolution of pelletizer, (3) added pelletization time. Green and sintered aggregate were measured specific gravity, absorption rate and average size. The optimum condition were found that the pelletization variables were angle at $70^{\circ}$, speed of revolution of pelletizer at 23.2 rpm, and water/solid ratio at 1/5. At these conditions, it was formed that fine aggregate green whose average size was $2.0{\sim}3.35mm$. Specific gravity and average size are increased with low angle of disc and fast revolution speed of disc. Specific gravity and average size were not distinctly influenced by added pelletization time. Sintered aggregate was distinctly influenced by properties of green.

• 한국전기전자재료학회논문지
• /
• 제23권3호
• /
• pp.199-205
• /
• 2010

The crystallization speed (v) of amorphous (InTe)$_x$(GeTe) (x = 0.1, 0.3 and 0.5) films and their thermal, optical and electrical behaviors have been investigated using nano-pulse scanner (wavelength = 658 nm, laser beam diameter < 2 ${\mu}m$), X-ray diffraction (XRD), 4-point probe and UV-vis-IR spectrophotometer. These results were compared with those of $Ge_2Sb_2Te_5$ (GST) film, comprehensively utilized for phase-change random access memory (PRAM). Both v-value and thermal stability of (InTe)$_{0.1}$(GeTe) and (InTe)$_{0.3}$(GeTe) films could be enhanced in comparison with those of the GST. Contrarily, the v-value in the (InTe)$_{0.5}$(GeTe) film was so drastically deteriorated that we could not quantitatively evaluate it. This deterioration is thought because amorphous (InTe)$_{0.5}$(GeTe) film has relatively high reflectance, resulting in too low absorption to cause the crystallization. Conclusively, it could be thought that a proper compositional (InTe)$_x$(GeTe) films (e.g., x < 0.3) may be good candidates with both high crystallization speed and thermal stability for PRAM application.

• Preventive Nutrition and Food Science
• /
• 제17권3호
• /
• pp.203-209
• /
• 2012

The effects of variable moisture content, screw speed and barrel temperature on the physicochemical properties of red ginseng powder extrudates were investigated. The raw red ginseng powders were processed in a co-rotating intermeshing twin-screw extruder. Primary extrusion variables were feed moisture content (20 and 30%), screw speed (200 and 250 rpm) and barrel temperature (115 and $130^{\circ}C$). Extruded red ginseng showed higher crude saponin contents (6.72~7.18%) than raw red ginseng (5.50%). Tested extrusion conditions did not significantly affect the crude saponin content of extrudates. Increased feed moisture content resulted in increased bulk density, specific length, water absorption index (WAI), breaking strength, elastic modulus and crude protein content and decreased water solubility index (WSI) and expansion (p<0.05). Increased barrel temperature resulted in increased total sugar content, but decreased reducing sugar content in the extrudate (p<0.05). Furthermore, increased barrel temperature resulted in increased amino acid content and specific length and decreased expansion and bulk density of extrudates only at a higher feed moisture content. The physicochemical properties of extrudates were mainly dependent on the feed moisture content and barrel temperature, whereas the screw speed showed a lesser effect. These results will be used to help define optimized process conditions for controlling and predicting qualities and characteristics of extruded red ginseng.

• 한국의류학회지
• /
• 제34권12호
• /
• pp.2062-2072
• /
• 2010

This research evaluates the change of the water absorbency and drying speed of a quick-drying knit fabric by repeated laundering and laundering conditions and investigates the influence of laundering conditions on the functional properties of the knit fabric. Four factors of laundering conditions were studied: detergent, water hardness, water temperature, and frequency of rotation. Knit fabrics were washed for 25 laundering cycles in a drum-type washing machine with nine different laundering conditions derived from an orthogonal array. The properties of knit fabrics were measured with a drop absorption test, a strip test, and a drying time test. Relaxation shrinkage pointed to a change in the structural characteristics of the knit fabric. Wetting time was faster and wickability was greater in the knit fabrics that underwent 5 laundering cycles; in addition, there were no obvious changes in wetting time and wickability. The detergent was the most important factor in wetting time (40.4%) and wickability (60% or above). Water hardness, water temperature and RPM had less of an effect on wetting time and wickability. There were no significant differences between the levels of laundering conditions (except for detergent) on wetting time and wickability. Drying times with neutral and alkali were slower by repeated laundering; however, there was no obvious change in drying time. Hardness, water temperature and RPM had less of an impact on drying time.