• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.372-375
• /
• 2001

본 논문에서는 고속데이터 전송을 위한 CDMA 모뎀를 구현하였다. 데이터율 1Mbps의 트래픽 5채널에 직교부호를 곱하여 채널을 구분한 후 하나의 채널로 처리하였다. I,Q로 입력된 신호는 복소 곱셈기에서 칩 레이트 8Mcps로 OCQPSK(또는 HPSK) 변조하였다. 복조기는 I,Q의 신호를 역확산한 후 직교부호를 다시 곱하여 각 채널의 데이터를 분리한다. 변복조기의 구현은 클럭 속도 167MHz의 부동 소수점형 프로세서인 TI사의 TMS320C6701 DSP(Digital Signal Processor)를 사용하었고, long code 및 I,Q 채널 PN 코드는 IMT-2000 동기방식과 비동기방식의 규격에 정의된 2가지의 PN코드 발생기를 모두 구현하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.632-635
• /
• 2003

[ $(Ba,Sr,Ca)TiO_3$ ] powders, prepared by the sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen printing techniques on alumina substrates. The dielectric properties were investigated for various composition ratio and $Nb_2O_5$ doping contents. All the BSCT thick films, sintered at $1420^{\circ}C$, showed the typical XRD patterns of a perovskite polycrystalline structure. The Curie temperature and the relative dielectric constant decreased with increasing Ca content and $Nb_2O_5$ doping amount. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) thick films doped with 1.0wt% $Nb_2O_5$ were 1410, 0.65% and 17.29% respectively.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.401-402
• /
• 2006

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1997년도 제12회 학술발표회 논문개요집
• /
• pp.25-26
• /
• 1997

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.304-309
• /
• 2000

Strain gage method is used to evaluate the mode I dynamic stress intensity factor of marging steel(18Ni) and titanium alloy(Ti-6A1-4V). To decide the best strain gage position on specimen, static fracture toughness test was performed. Then instrumented charpy impact test and dynamic tensile test was performed by using strain gage method for evlauating dynamic stress intensity factor. Strain gage signals on the crack tip region are used to calculate the stress intensity factors. It is found that strain gage method is more useful than method by using load which is obtained from impact tup to assess dynamic characteristics such as dynamic stress intensity factor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.332-336
• /
• 2001

In this study, the reaction at UBM(Under Bump Metallurgy) and solder interface was investigated. The UBM employed in conventional optical packages, Au/Pt/Ti layer, were found to dissolve into molten Au-Sn eutectic solder during reflow soldering. Therefore, the reaction with different diffusion barrier layer such as Fe, Co, Ni were investigated to replace the conventional Pt layer. The reaction behavior was investigated by reflowing the solder on the pad of the metals defined by Cr layer for 1, 2, 3, 4, and 5 minutes at $330^{\circ}C$. Among the metals, Co was found to be most suitable for the diffusion barrier layer as the wettability with the solder was reasonable and the reaction rate of intermetallic formation at the interface is relatively slow.

• 열처리공학회지
• /
• 제7권3호
• /
• pp.199-205
• /
• 1994

The fracture characteristics and tool life of ceramics and WC, CBN cutting tool when turning heat treated steel STD11($H_RC$ 60) were investigated experimentally to clarify the machinability and optimum tool materials in cutting of difficult-to-cut material with high hardness. Forthermore, the behaviors of the tool wear and failure were examined with regard to cutting force. The hardened steel wore the cutting tool edge rapidily and increased the cutting forces, especially radial force. The tool was worn by the abrasive action. Flank Weat of $Al_2O_3-TiC$ ceramic and WC tool become relatively large and CBN & $Al_2O_3$, ceramic tool had a long life among the tool materials tested. The tool fracture patterns were just like minor cutting wear, flank wear, crater wear, notch wear, chipping. Flank wear rate was accelerated by occurrence of chipping. During the proceeding of machining, it was possible to foresee the catastrophic fracture of tool by abrupt increase of radial force.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.201-203
• /
• 2005

A kinetic model for particle coarsening behavior in the weld heat affected zone (HAZ) was proposed. Unlike the conventional approach, where the mean-sized particle is considered to grow continuously, the proposed model considered the critical particle size which can be derived from the Gibbs-Thomson equation. In this study, the proposed particle coarsening model was applied to study the behavior of (Ti, Nb )(C, N) complex particle in the weld HAZ. The predicted particle size distributions using the proposed model were in agreement with the experimental results.

• 한국레이저가공학회지
• /
• 제15권2호
• /
• pp.1-5
• /
• 2012

Gelatin is used as a model for soft biological tissues in studying laser interaction with the soft tissues. In this work, we analyze the interaction between gelatin and excimer and Ti:Sapphire femtosecond laser under various conditions, especially by varying the laser, laser fluence and pulse number. The results show that swelling of the surface and ablation depth can be controlled by adjusting the process parameters.

• 한국표면공학회지
• /
• 제32권6호
• /
• pp.686-694
• /
• 1999

Insoluble anodes of the Ta/Ir mixed metal oxide for electrodeposition of Ni-W alloy in ammoniacal citrate bath were prepared by thermal decomposition method. Ti plate was etched in boiling oxalic acid solution and coated with ethanol solution of $TaCl_{5}$ and $IrCl_4$ mixed in a fixed ratio, followed by drying and treating at various temperatures. The coating layer of these insoluble anode was characterized by SEM, EDX, XRD and DSC. The decomposition rate of citric acid in plating bath was determined by measuring the $CO_2$ gas evolved at the anodes with Gas Chromatography. Evolution of $CO_2$ gas from Ta/Ir oxide anodes decreased about 5% compared with that of Pt. The $CO_2$ gas evolution was increased with the amount of Ir-oxide in the coatings. The coatings which have more than 40% ratio of Ta content and heat-treated at the temperature higher than $400^{\circ}C$ showed better efficiency