• 한국산학기술학회논문지
• /
• 제19권4호
• /
• pp.69-76
• /
• 2018

본 연구에서는 유정용 강관의 열처리 조건 및 합금원소(B, Ti)에 따른 미세조직 및 기계적 성질을 조사하였다. 실험에는 J55, J55+B,Ti 강재를 사용하였고, 열처리 조건은 각각 오스테나이트 처리온도 ($880^{\circ}C$, $910^{\circ}C$, $940^{\circ}C$), 냉각방식 (수냉, 유냉), 템퍼링 온도 (미실시, $550^{\circ}C$, $650^{\circ}C$) 이다. 열처리 조건에 따라 얻어지는 미세조직을 예측하기 위해 J55, J55+B,Ti 강재의 화학적 성분을 기준으로 평형상태도와 CCT 곡선을 예측하였다. 시뮬레이션 결과 평형상태도는 A1, A3 온도가 약 $20^{\circ}C$ 감소하였고, CCT 곡선은 B, Ti이 첨가됨에 따라 ferrite와 bainite nose 부분이 오른쪽으로 이동하였다. J55, J55+B,Ti 강재의 CCT 곡선을 기준으로 냉각속도에 따른 martensite, bainite, ferrite등 예상되는 미세조직을 예측하였고, J55 강재의 미세조직 예측값은 실제 실험값과 유사한 양상을 나타내었지만. J55+B,Ti 강재의 예측값은 실제 실험값과는 차이가 있었다. 열처리 조건이 변화됨에 따라 martensite, bainite, ferrite 등 다양한 조직이 생성되었으며, 이는 경도, 강도 및 연신율에 밀접한 영향을 미쳤다. J55시편의 수냉의 경우 martensite 조직이 형성되었고, 유냉의 경우 bainite와 ferrite 조직이 형성되었지만, J55+B,Ti시편은 B의 첨가에 의한 경화능 향상으로 냉각방식에 관계없이 martensite 조직이 형성되었다. 전반적으로 B, Ti을 첨가하면서 기계적 성질은 향상되었고, quenching 이후의 시편보다 tempering 이후의 시편에서 크게 향상되었다. 이는 Ti의 첨가로 인해 생성된 미세한 석출물이 재결정시 결정립 성장을 억제하여 미세한 오스테나이트 결정립을 생성하였고, tempering 열처리 이후에도 결정립 미세화 효과가 큰 영향을 미친 것으로 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1311-1312
• /
• 2006

This paper describes the ohmic contact formation between a TiW film as a contact material deposied by RF magnetron sputter and polycrystalline 3C-SiC films deposied on thermally grown Si wafers. The specific contact resistance (${\rho}_c$) of the TiW contact was measured by using 4he C-TLM. The contact phase and interfacial reaction between TiW and 3C-SiC at high-temperature were also analyzed by XRD and SEM. All of the samples didn't show cracks of the TiW film and any interfacial reaction after annealing. Especially, when the sample was annealed at $800^{\circ}$ for 30min., the lowest contact resistivity of $2.90{\times}10^{-5}{\Omega}{\cdot}cm^2$ of was obtained due to the improved interfacial adhesion.

• 한국표면공학회지
• /
• 제24권1호
• /
• pp.16-16
• /
• 1991

Generally brittle eta phase produced during TiC deposition has a effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η), phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase)have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as follows; 1. by inserting underlayer eta phase were decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest grain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• 한국표면공학회지
• /
• 제25권1호
• /
• pp.16-23
• /
• 1992

Generally brittle eta phase produced during TiC deposition has a bad effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η) phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase) have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as fellows; 1. by inserting underlayer eta phase was decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest gain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• 한국재료학회지
• /
• 제15권10호
• /
• pp.662-666
• /
• 2005

Solid solutions of $(Zr/Ti)O_2$ were prepared in powder form by the coprecipitation technique. After mixing with carbon or exposing to nitrogen gas at elevated temperature, titanium cations selectively diffused out from the oxide compound to form titanium carbide (TiC) or titanium nitride (TiN), respectively. TiN formed strong interfacial contacts between the oxide grains. In contrast, TiC formed as small crystallites on oxide grains but did not bind the matrix grains together. TiN therefore played a role in strengthening the interparticle bonding, but TiC weakened the bonding between grains. Partial diffusion of titanium cations also led to nanolayered structure being formed between the oxide grains, which provided weak interfacial layers that fractured in a step-wise fashion.

• 한국재료학회지
• /
• 제12권11호
• /
• pp.889-893
• /
• 2002

The reactions of $Cu/Ti/SiO_2$ structures at temperatures ranging from 200 to $700^{\circ}C$ have been studied for various Ti thicknesses. The reaction products initially formed, at around $300^{\circ}C$, were a series of Cu-Ti intermetallics ($Cu_3$Ti/CuTi) with the oxygen dissolved in the Ti moving from the compounds into the remaining unreacted Ti. At $500^{\circ}C$, the $Cu_3$Ti was converted into Cu-rich intermetallics, $Cu_4$Ti, which grew at the expense of the CuTi due to the increased oxygen content in the Ti. In addition, the outdiffusion of Ti, to the Cu surface, and the $Ti-SiO_2$ reactions, caused an abrupt increase in the oxygen content in the Ti layer, which placed thermodynamic restraints on further Ti reactions. Furthermore, thinner Ti layers showed a higher increasing rate of oxygen accumulation for the same consumption of Ti, which led to significantly reduced Ti consumption. The $SiO_2$ film under the Ti diffusion barrier was more easily destroyed with increasing Ti thickness.

• The Korean Journal of Ceramics
• /
• 제5권4호
• /
• pp.317-323
• /
• 1999

Si3N4-TiC composites have been known as electrically conductive ceramics. $Si_3N_4-TiC$ composites with 2 wt% $Al_2O_3$ and 4 wt% $Y_2O_3$ were hot pressed in $N_2$ environment. The mechanical properties including hardness, fracture toughness, and flexural strength and tribological properties were investigated as a function of TiC content. $Si_3N_4-40$ vol% TiC composite was hot pressed at $1,750^{\circ}C$, $1,800^{\circ}C$, and $1,850^{\circ}C$ for 1, 3 and 5 hours in $N_2$ gas. Mechanical and tribolgical properties depended on microstructures, which were controlled by hte TiC content, hot press temperature, and hot press holding time. However, mechanical properties and tribological behaviors were degraded by the chemical reaction between TiC and N. The chemically reacted products such as TiCN, SiC, and $SiO_2$ were detered by the X-ray diffraction analysis.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.114-115
• /
• 2013

$Ti_3AlC_2$ was corroded between 800 and $1100^{\circ}C$ in an Ar-0.2% $SO_2$ gas atmosphere according to the equation: $Ti_3AlC_2+O_2{\rightarrow}rutile-TiO_2+{\alpha}-Al_2O_3$ + (CO or $CO_2$). The scales that formed on the $Ti_3AlC_2$ were thin and rich in ${\alpha}-Al_2O_3$, whose growth rate was exceedingly slow. The $TiO_2$ was present either as the outermost surface scale or a mixture inside the ${\alpha}-Al_2O_3$-rich scale. In the $Ti_3AlC_2$, the activity and diffusivity of Ti were low, whereas those of Al were high. This was the main reason for the superior corrosion resistance of $Ti_3AlC_2$ over TiAl.

• 한국주조공학회지
• /
• 제24권3호
• /
• pp.159-164
• /
• 2004

The aim of the present work is to investigate the possibility of in-situ synthesis and net-shape forming of the titanium matrix (TiC+TiB) hybrid composites using a casting route. From the scanning electron microscopy, electron probe micro-analyzer, X-ray diffraction and thermodynamic calculations, the spherical TiC and needle like TiB reinforced hybrid titanium matrix composites could be obtained in-situ by the conventional melting and casting route between titanium and $B_4C$. No melt-mold reaction occurred between the titanium matrix (TiC+TiB) hybrid composites and the SKK mold, since the mold is consisted with interstitial and substitutional metal-mold reaction products. Not only the sound in-situ synthesis but also the economic net-shape forming of the titanium matrix (TiC+TiB) hybrid composites could be possible by the conventional casting route.

• 한국재료학회지
• /
• 제19권7호
• /
• pp.397-402
• /
• 2009

In this study, Ti powder was fabricated from Ti scrap by the Hydrogenation-Dehydrogenation (HDH) method. Hydrogenation reactions of Ti scrap occurred at near 450 $^{\circ}C$ with a sudden increase in the reaction temperature and the decreasing pressure of hydrogen gas during the hydrogenation process in the furnace. The dehydrogenation process was also carried out at 750 $^{\circ}C$ for 2hrs in a vacuum of $10^{-4}$ torr. After the HDH process, a deoxidation treatment was carried out with the Ca(purity: 99.5) at 700 $^{\circ}C$ for 2hrs in the vacuum system. It was found that the oxidation content of Ti powder that was deoxidized with Ca showed noticeably lower values, compared to the content obtained by HDH process. In order to fabricate Ti compacts, Ti powder was sintered at $1100\sim1400^{\circ}C$ for 2hrs under a vacuum of $10^{-4}$ torr. The relative density of compact was 94.9% at 1300 $^{\circ}C$. After sintering, all of the Ti compacts showed brittle fracture behavior, which occurred in an elastic range with short plastic yielding up to a peak stress.