• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5A
• /
• pp.255-266
• /
• 2012

Main cable of a suspension bridge is the important member which shows the overall structure integrity at bridge completion. Configuration of main cable is a free hanging state at cable erection completion and is different from that at bridge completion supporting the dead loads such as hanger, girder, and so on. Accordingly, the configuration control under cable erection is considerably significant because the configuration at cable erection completion has direct influence on that at bridge completion. That is performed by sag adjustments at center, side span and tension adjustments at anchor span. The former needs the sag sensitivity which represents the control quantity of strand length corresponding to that of sag. The latter requires the tension sensitivity which shows the change of strand tension according to that of strand temperature. In this study, the fundamental equations of cable were derived with the assumption of either catenary or parabola shape, the differential-related equations using chain rule on horizontal tension were drawn from those and finally the estimation methods of the sag / tension sensitivity were proposed from both those. The nonlinear numerical analysis flow charts of sag sensitivity based on the catenary equations were proposed and the sag sensitivities grounded on the differential-related equations were compared with the results using them for various parameters of sag change. Also, considering the combinations of sag change parameters, the calculation method of the final variation for the cable sag was suggested. For the real suspension bridge under construction with PPWS method, the sag/tension sensitivity were estimated considering the construction conditions like the change of PPWS length, PPWS temperature, bridge span, etc.. We hope that this study will be a systematic guideline for the configuration control under main cable erection and improved highly by field verification in the real bridge site.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.2
• /
• pp.79-86
• /
• 2014

This paper describes an integrity evaluation method for emergency diesel generator(EDG) and rotor part of EDG. EDG is a very important equipment in the nuclear power plant(NPP). EDG supplies electricity to the safety-related equipments for the safety shut down of NPP in an emergency situation of earthquake. The safety of the rotor part of EDG is also important during seismic impact from earthquake. The finite element modelling of the EDG including rotor part was constructed. The modal analysis of EDG was firstly performed. The first natural frequency was calculated and revealed higher than the cutoff frequency of seismic spectrum. Then the stress analysis was done to compare with the allowable stress. The safety of the rotor part was investigated by the finite element analysis of the rotor and journal bearing interaction to find film thickness and critical speed. The seismic load was applied to rotor part in a manner that the load was a weighted static load. Analysis results showed that the maximum stress was within the range of allowable stress and the film thickness is larger than the permissible minimum thickness, and the critical speed was out of the operating speed. Hence, the structural and dynamic integrity of EDG could be confirmed by the numerical analysis method used in this paper. However, dynamic analysis of a rotating rotor and supporting bearing with the seismic impact needs to be investigated in a more rigorous method since the seismic load to the rotating part complicates the behavior of rotating system.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.19 no.1
• /
• pp.87-91
• /
• 2005

Dental plaque is a film of microorganisms on the tooth surface that plays an important part in the development of caries and periodontal diseases. Streptococcus mutans (S. mutans) is present in almost all types of dental plaque. Teeth and their supporting structure, the gums (gingiva) are subjected to infection by S. mutans that causes cavities and pyorrhea which, if left untreated, can eventually lead to gingivitis. Various chemical agents have been evaluated over the years with respect to their antimicrobial effects in the oral cavity; however, all are associated with side effects that prohibit regular long-term use. The present study was designed to investigate the effect of Aralia continentalis (Araliaceae) extracts on the growth, acid production, adhesion, and insoluble glucan synthesis of S. mutans. The methanol extract of A. continentalis showed concentration dependent inhibitory activity against the growth and acid production of S. mutans, and produced significant inhibition at the concentration of 0.25, 0.5, 1, 2 and 4 mg/ml compared to the control group. The extracts markedly inhibited S. mutans adherence to HA treated with saliva, and cell adherence was repressed by more than 60% at the concentration of 0.25 mg/ml and complete inhibition was observed at the concentration of 4 mg/ml. On the activity of glucosyltransferase which synthesizes water insoluble glucan from sucrose, methanol extract of A. continentalis showed more than 10% inhibition over the concentration of 0.25 mg/ml. The synthesis of insoluble glucan was decreased in the presence of 0.25 - 4 mg/ml of the methanol extract of A. continentalis. Hence, we conclude that A. continentalis might be a candidate of anticaries agent.

• Ocean and Polar Research
• /
• v.30 no.3
• /
• pp.303-312
• /
• 2008

Despite the impacts of the climate changes on the pelagic ecosystem, few studies have examined the pelagic-benthic coupling in the adjacent East China Sea and Korea Strait. Therefore, the species composition and abundance of the macrobenthic community, as well as the potential food sources of benthic fauna were investigated in the present study using stable isotope analysis (${\delta}^{13}C\;and\;{\delta}^{15}N$) for suspended particulate organic matter (SPOM), sedimentary organic matter (SOM), phytoplankton, and zooplankton. A total of 157 macrobenthic fauna were collected, and the density of the macrobenthic fauna ranged from 4 to 434 ind./0.25 $m^2$, with an average density of 149 ind./0.25 $m^2$. The density of the benthic fauna increased moving from offshore shelf sites to coastal sites adjacent to the Korea Strait. Cluster analysis showed that the macrobenthic communities consisted of three distinct groups: group A in the Korea Strait, group B in the East China Sea, and group C near Ieodo. The dominant species in group A were the amphipods Photis japonica and Ampelisca miharaensis, followed by the polychaete Scolotoma longifolia. Environmental variables, such as the temperature of the seawater and sediment, and oxygen, and chlorophyll a levels, appeared to affect the structure of the community, suggesting the importance of coupling with the pelagic system. The ${\delta}^{13}C$ values of SPOM and zooplankton ranged from -22.97 to -23.5% and -19.92 to -21.86%, respectively, showing a relatively narrow range(<1%) between the two components. The difference between the ${\delta}^{13}C$ values of SOM and pelagic organic matter was also within 1%, suggesting that the SOM originated from the pelagic system, which is an important factor controlling the macrobenthic community.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.4
• /
• pp.43-51
• /
• 2014

A Large-diameter drilled shaft of deep water depth composite foundation supporting a high rise pylon of the test designed super long span bridge was designed by allowable stress design method and failure probability through reliability analysis to bearing capacity was estimated. The allowable stress design results for the bearing capacity of a drilled shaft were analyzed by reliability analysis and the probability of failure shows 0.12 % in case of CFEM, 0.0002 % in case of Korea Highway Corporation criterion, and 0.003 % in case of structure foundation design criterion. In the allowable stress design, the bearing capacity of a large-diameter drilled shaft was obtained by applying to safety factor 3 and reliability analysis for the results was done. If the failure probability suggested by AASHTO(2007) specification is set to 0.02 %, the socketed length of a drilled shaft shows an increase of 25 % in CFEM, decrease of 60 % in KHCC, and decrease of 89 % in SFDC.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.25 no.1
• /
• pp.35-49
• /
• 2016

With the increasing demand for aesthetic implant dentistry, the importance of implant restoration is emphasized not only in the functional aspect but also in the aesthetic aspect. The aesthetic restoration of dental implants in the anterior maxilla is a challenge for clinicians because it requires proper harmony in three following conditions; reconstruction of hard tissue, soft tissue, and aesthetic prosthesis. The soft tissue aesthetics are dependent upon the condition of the supporting hard tissue because the osseous structure provides a framework for the development of a healthy and aesthetic soft tissue interface. Therefore, the augmentation of hard tissue is a first step and especially, optimal 3-dimensional position of implant is the most important factor in aesthetic implant restoration. The management of soft tissue is a second step, and the final step is a restoration of harmonic prosthesis using provisional restoration with proper emergence profile. This clinical report describes the procedure of bone augmentation in labial dehiscence defect, Vascularized Interpositional Periosteal-Connective Tissue (VIP-CT) flap for aesthetic anterior soft tissue, and the importance of provisional restoration and impression taking stage with customized impression coping.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.1
• /
• pp.55-59
• /
• 2010

Currently in a Ubiquitous Sensor Network (USN) research field, supporting mobility is recognized as an important technology. MIPv6 and Network Mobility(NEMO) Basic Support Protocol are standard protocols to support mobility in the Internet. However, if they are applied to USN with no modification, handoff performance decreases due to the size of their binding message. An existing lightweight protocol for NEMO protocol has a compatibility problem of Sequence Num. and does not optimally compress binding messages considering 6LoWPAN network structure and addressing. This paper proposes optimal header compression which supports node-based mobility and network-based mobility. Our optimal compression technique compresses a 32bytes binding update(BU) message and a 12bytes binding ACK(BA) message of MIPv6 into 13bytes and 3bytes, and a 40bytes BU message and a 12bytes BA message of NEMO protocol into 13bytes and 3bytes. The result shows that our protocol compresses 15bytes (NEMO-BU) and 1byte (NEMO-BA) more than the existing protocol and achieves 8.72% handoff performance improvement.

• Korean Journal of Heritage: History & Science
• /
• v.45 no.4
• /
• pp.92-103
• /
• 2012

The Cheomsungdae was built in the Silla dynasty during the reign of queen Seondeok. It has a round cylindrical structure with a flowing curved fa ade. The identity of the Cheomsungdae has not been revealed since there is not much historical evidence or documents about the building. This study is trying to investigate the building technique and method from the technical point of view of the past when it was constructed. There have been much work and studies done for the Cheomsungdae, but not much were focusing on the technical aspects of the building. In addition there are many questions and doubts about the hypothesis of the building technique of Cheomsungdae since there aren't any remaining documents or historical evidence supporting it. Among many questions, we think that the discussion on falsework technique is not considering traditional construction method of the Dujabee (a traditional construction technique using various tools and equipment for the stability of the building) technique. Therefore, it is hard to identify them as reliable historical facts. As the result of the study, we want to provide the basic data on the construction techniques of Korean traditional architecture and broaden the study scope of technical history by narrowing the errors. The study could be summarized into three points. 1. The historical architecture Cheomseongdae was constructed by using traditional crane techniques such as a Noklo (pulley ladder). Cheomseongdae was re-evaluated as a high level technology for the history of architecture. 2. The benchmark method on Cheomseongdae construction has been applied with a precise scientific method based on the geometrical principals using the central axis. 3. In terms of the history of Korean traditional architecture technology, as there aren't many studies done we proposed various basic data for the traditional crane techniques and criteria of Korean traditional architecture technology. We could expect various and active studies for the technical approach of the history of architecture.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.3
• /
• pp.359-369
• /
• 2021

Implant prostheses and removable partial dentures are mainly used as treatment methods for partial edentulous patients who have lost a number of teeth. The implant-assisted removable partial denture (IARPD) is strategically selected. The defect in maxillofacial structure due to osteomyelitis, a type of facial bone infection, causes dysfunction such as mastication, swallowing, and pronunciation, as well as social and psychological effects, so a removable restoration is required to restore the supporting tissue. Design of abutment and partial dentures is an essential factor in the success of treatment. In this case, IARPD, which has superior retention and stability compared to traditional removable partial dentures, can have a good prognosis. In a partial edentulous patient with bone defects due to osteomyelitis treatment, the stability of the denture was secured with IARPD restoration. Moreover, maintenance problem that may occur in the future was minimized by providing an appropriate denture design and occlusal scheme through several provisional restorations. This case can be expected to have a favorable prognosis in the long term.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.4
• /
• pp.529-537
• /
• 2021

Membrane-type hull and cargo holds have been designed and built for large ship. However, there is a growing interest in applying the same technology to small and medium-sized Liquefied natural gas(LNG) carriers to meet the recent increase in demand for LNG as an ecofriendly fuel and for expanding LNG bunkering infrastructure. The purpose of this study is to apply the IMO Type-B tank to small and medium-sized LNG carriers and verify the safety and suitability of the design. Fatigue crack propagation analysis was performed to install a partial second drip tray installed at the lower part of the LNG cargo tank by calculating the amount of leaked gas in the support structure supporting the cargo tank. First, a program for fatigue crack propagation analysis was developed, in which Paris' law and British Standard 7910 (BS 79110) were applied based on the International Code for the Construction of Equipment and Ships Carrying Liquefied Gases in Bulk, an international standard for LNG carriers. In addition, a surface crack propagation analysis was performed. Next, a methodology for assuming the initial through-crack size was developed to determine the size of the partial second barrier. The analysis was performed for 15 days, which is a possible return time after cracks are detected. Finally, the safety and suitability of the IMO Type-B for LNG cargo tanks required by international regulations were verified. For the accurate analysis of fatigue crack propagation, it is necessary to develop and verify the analysis procedure based on direct analysis and international regulations.