• Journal of Aerospace System Engineering
• /
• v.11 no.4
• /
• pp.8-14
• /
• 2017

In this study, the production of proper emulsion fuel and the evaluation of its rheological stability in various experimental conditions were carried out. The W/O (water-in-oil) emulsion fuel was made using n-decane, pure water, and Span 80 was used as a surfactant. Increments of water volume ratio and fuel temperature were the factors, which boosted the phase separation of the emulsion fuel. Rheological characteristics for different water/oil volume ratio, temperature, and elapsed time after the fuel production were examined. As the water volume ratio in the fuel increased, the behavior of non-Newtonian fluid was observed. Viscosity declined as the fuel temperature increased due to the cohesion of water droplets in the fuel. The effect of elapsed time on viscosity was not severe for lower water ratio. However, gradual decrease of viscosity 3 hours after fuel production, in the case of ratio of 3:7, was clearly observed.

• Journal of Pharmaceutical Investigation
• /
• v.39 no.3
• /
• pp.185-199
• /
• 2009

Using a strain-controlled rheometer [Advanced Rheometric Expansion System (ARES)], the steady shear flow properties and the dynamic viscoelastic properties of $Antiphlamine-S^{(R)}$ lotion have been measured at $20^{\circ}C$ (storage temperature) and $37^{\circ}C$ (body temperature). In this article, the temperature dependence of the linear viscoelastic behavior was firstly reported from the experimental data obtained from a temperature-sweep test. The steady shear flow behavior was secondly reported and then the effect of shear rate on this behavior was discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters. The angular frequency dependence of the linear viscoelastic behavior was nextly explained and quantitatively predicted using a fractional derivative model. Finally, the strain amplitude dependence of the dynamic viscoelastic behavior was discussed in full to elucidate a nonlinear rheological behavior in large amplitude oscillatory shear flow fields. Main findings obtained from this study can be summarized as follows : (1) The linear viscoelastic behavior is almostly independent of temperature over a temperature range of $15{\sim}40^{circ}C$. (2) The steady shear viscosity is sharply decreased as an increase in shear rate, demonstrating a pronounced Non-Newtonian shear-thinning flow behavior. (3) The shear stress tends to approach a limiting constant value as a decrease in shear rate, exhibiting an existence of a yield stress. (4) The Herschel-Bulkley, Mizrahi-Berk and Heinz-Casson models are all applicable and have an equivalent validity to quantitatively describe the steady shear flow behavior of $Antiphlamine-S^{(R)}$ lotion whereas both the Bingham and Casson models do not give a good applicability. (5) In small amplitude oscillatory shear flow fields, the storage modulus is always greater than the loss modulus over an entire range of angular frequencies tested and both moduli show a slight dependence on angular frequency. This means that the linear viscoelastic behavior of $Antiphlamine-S^{(R)}$ lotion is dominated by an elastic nature rather than a viscous feature and that a gel-like structure is present in this system. (6) In large amplitude oscillatory shear flow fields, the storage modulus shows a nonlinear strain-thinning behavior at strain amplitude range larger than 10 % while the loss modulus exhibits a weak strain-overshoot behavior up to a strain amplitude of 50 % beyond which followed by a decrease in loss modulus with an increase in strain amplitude. (7) At sufficiently large strain amplitude range (${\gamma}_0$>100 %), the loss modulus is found to be greater than the storage modulus, indicating that a viscous property becomes superior to an elastic character in large shear deformations.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.23-29
• /
• 2011

We measured shear viscosity of polymeric particles, prepared by suspension polymerization with hydrophobic silica as a stabilizer at $75^{\circ}C$, by a capillary rheometer. Shear viscosity displayed a non-Newtonian behavior with an increase in weight average molecular weight. Measurement of shear viscosity at 170 and $190^{\circ}C$ with copoly(styrene/butyl methacrylate) (co-PSB) particles by varying the ratio between styrene (St) and butyl methacrylate (BMA) showed that shear viscosity was a function of molecular weight, temperature and compositional ratio. When the ratio was 7/3, 5/5 and 3/7, shear viscosity slightly reduced with an increase in BMA concentration despite similar weight average molecular weights. We found that shear viscosity of copolymers with BMA concentrations exceeding 70% displayed a sharp reduction at high shear rates. It is speculated that increased PBMA chain length contributes to enhanced flowability of copolymers. When carbon black was incorporated into co-PSB, shear viscosity progressively increased with increasing carbon black concentration. The increase in shear viscosity, however, was less pronounced compared to the cases of molecular weight increase.

• Journal of Korea Water Resources Association
• /
• v.54 no.11
• /
• pp.943-953
• /
• 2021

The propagation of impact wave induced by landslide and debris flow occurred on the slope of lake, reservoir and bays is a three-dimensional natural phenomenon associated with strong interaction of debris flow and water flow in complex geometrical environments. We carried out 3D numerical modeling of such impact wave in a bay using a multiphase turbulence flow model and a rheology model for non-Newtonian debris flow. Numerical results are compared with previous experimental result to evaluate the performance of present numerical approach. The results underscore that the reasonable predictions of both thickness and speed of debris flow head penetrating below the water surface are crucial to accurately reproduce the maximum peak height and free surface profiles of impact wave. Two predictions computed using different initial debris flow thicknesses become different from the instant when the peaks of impact waves fall due to the gravity. Numerical modeling using relatively thick initial debris flow thickness appears to well reproduce the water surface profile of impact wave propagating across the bay as well as wave run-up on the opposite slope. The results show that the maximum run-up height on the opposite slope is not sensitive to the initial thickness of debris flows of same total volume. Meanwhile, appropriate rheology model for debris flow consisting of inviscid particle only should be employed to more accurately reproduce the debris flow propagating along the channel bottom.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.603-607
• /
• 2023

Aqueous film forming foam (AFFF) is a critical fire suppression agent used in combating hydrocarbon fires. This type of fire suppressant is highly effective due to its ability to form a protective film, dissipate heat, inhibit combustion, and utilize a blend of chemical substances to extinguish fires. While these properties offer significant advantages in responding to hydrocarbon fires, AFFF is distinct in its deployment as it is dispensed in the form of foam. Therefore, the rheological analysis of AFFF foam using a rheometer plays a crucial role in predicting the spray characteristics of AFFF for combating hydrocarbon fires, and this is closely associated with effective fire suppression. In this study, we conducted rheometer experiments to confirm the non-Newtonian behavior (shear-thinning) of AFFF foam and obtained data on the form's stability. These experimental data are expected to contribute to enhancing the efficiency of fire suppression systems utilizing AFFF.

• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.295-300
• /
• 2004

Coil embolization technique has been used recently to treat cerebral aneurysms. When a giant or a multilobular aneurysm are treated by roils, filling an aneurysm sac completely with coils is difficult and partial blocking of an aneurysm sac is inevitable. Blood flow characteristics, which nay affect the embolization process of an aneurysm sac, are changed by the locations of coils for the Partially blocked aneurysms. Blood flow fields are also influenced by the geometry of a parent vessel. In order to suggest the coil locations effective for aneurysm embolization, the blood flow fields of lateral aneurysm models were analyzed for the different coil locations and parent vessel geometries. Three dimensional pulsatile flow fields are analyzed by numerical methods considering non-Newtonian viscosity characteristics of blood. Flow rate into the aneurysm sac (inflow rate) and wall shear stress, which are suspected as flow dynamic factors influencing aneurysm embolization, are also calculated. Inflow rates were smaller and the low wall shear stress zones were larger in the neck blocked models compared to the dome blocked models. Smaller inflow and larger low wall shear stress zones in the distal neck blocked model imply that the distal neck should be the effective coil locations for aneurysm embolization.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.3
• /
• pp.335-341
• /
• 2013

Kyungokgos purchased in local markets in Korea vary in their combination and mixing ratios during processing. This study was investigated qualities of Kyungokgos manufactured traditionally to evaluating its qualities. The general components of Kyungokgos were moisture (18.62~49.78%), ash (0.198~1.211%), protein (0.89~3.58%), lipid (0.16~1.14%) and carbohydrates (47.95~77.08%). The color values of L, a, and b were 26.49~73.87, 16.51~38.64, and 45.41~88.94, respectively. The viscosity was classified into three non-Newtonian type groups: high, medium, and non-dilatant, according to the increase of loop execution times. Three extracts (KOG-1, -7, and -8, in a 30-fold dilution) showed no cytotoxicity toward RAW 264.7 cells, while the extracts of KOG-2, -4, and -5 showed a low cytotoxic effect. KOG-1 and -2 extracts with low cytotoxicity markedly inhibited the production of the inflammatory mediators-nitric oxide (NO) and tumor necrosis factor-alpha (TNF-${\alpha}$) in LPS-stimulated RAW 264.7 cells. These results indicate that KOG-1 and -2 extracts have anti-inflammatory activity in LPS-stimulated RAW 264.7 macrophages.

• Journal of Life Science
• /
• v.25 no.9
• /
• pp.1027-1035
• /
• 2015

A strain GP32 which produces a highly viscous extracellular polysaccharide was conducted with soil samples and identified as Pseudomonas species. The culture flask conditions for the production of extracellular polysaccharide by Pseudomonas sp. GP32 were investigated. The most suitable carbon and nitrogen source for extracellular polysaccharide production were galactose and (NH₄)₂SO₄. The optimum carbon/nitrogen ratio for the production of extracellular polysaccharide was around 50. The optimum pH and temperature for extracellular polysaccharide production was 7.5 and 32℃, respectively. In batch fermentation using a jar fermentor, the highest extracellular polysaccharide content (15.7 g/l) was obtained after 70 hr of cultivation. The extracellular polysaccharide produced by Pseudomonas sp. GP32 (designated Biopol32) was purified by ethanol precipitation, cetylpyridinium chloride (CPC) precipitation, and gel permeation chromatography. Biopol32, which has an estimated molecular weight of over 3×10⁷ datons, is a novel polysaccharide derived from sugar components consisting of galactose, glucose, gulcouronic acid and galactouronic acid in an approximate molar ratio of 1.85 : 3.24 : 1.00 : 1.42. The solution of Biopol32 showed non-Newtonian characteristics. The viscosity of Biopol32 exhibited appeared to be higher at all concentration compared to that of zooglan from Zoogloea ramigera. An analysis of the flocculating efficiency of Biopol32 in industry wastewater (food, textile, and paper wastewater) revealed chemical oxygen demand (COD) reduction rates 58.4-67.3% and suspended solid (SS) removal rates 82.6-91.3%. Based on these results, Biopol32 is a possible candidate for industrial applications such as wastewater treatment.