• Applied Science and Convergence Technology
• /
• 제24권4호
• /
• pp.84-89
• /
• 2015

The base pressure and outgassing rate of a mild steel chamber were measured and compared to those of a stainless steel chamber. A combined sputter-ion and non-evaporable getter pump with a nominal pumping speed of 490 l/s generated the base pressure of $2.7{\times}10^{-11}$ mbar in the mild steel chamber and $1.2{\times}10^{-10}$ mbar in the stainless steel chamber. The rate-of-rise measurements show that the mild steel has an extremely low outgassing rate of $2.6{\times}10^{-13}$ mbar $ls^{-1}cm^{-2}$, which is about one-order of magnitude smaller than the outgassing rate of the stainless steels. Vacuum annealing of the mild steel at $850^{\circ}C$ reduced the outgassing rate further to $8.8{\times}10^{-14}$ mbar $ls^{-1}cm^{-2}$, which was comparable to the outgassing rate of a heat treated stainless steel for extreme-high vacuum use.

• 산업기술연구
• /
• 제33권A호
• /
• pp.3-8
• /
• 2013

Reduction of risk plays a pivotal role in the development of medical instruments. A hyperbaric oxygen chamber, as a medical device, is known to help medical therapy for diversity of diseases through provision of high purity oxygen. The use of hyperbaric oxygen is expected to increase in the future and study to rigorously examine reliability and safety is needed. We have performed risk assessment for a newly developed hyperbaric oxygen chamber in this study. We first briefly discussed the system structure and concept of risk assessment for the study. Based on the hazards identified, we performed preliminary hazard analysis for the chamber.

• 한국분무공학회지
• /
• 제2권2호
• /
• pp.24-34
• /
• 1997

This paper describes the investigation of combustion characteristics of gasoline-methanol blend in constant volume combustion chamber. A constant volume combustion chamber was used to elucidate a basic combustion characteristics and the premixer was installed to control temperature and equivalence ratio. And the maximum pressure, combustion duration and flame propagation according to the evaporation rate were measured to determine the optimal temperature range for evaporating a blend fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deteriorated by decreasing surrounding temperature of fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deter orated by decreasing surrounding temperature of fuel injected. It was also found that the overall gasification process for methanol blend fuel was influenced by a combustion chamber temperature rather than a premixer temperature.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.265-268
• /
• 2005

Jet A-1과 액체산소를 추진제로 하는 연소압 52.5 bara 추력 30 tonf급 로켓엔진 연소기의 2단 점화시험을 수행하였다. 점화방식으로 TEAL과 액체산소를 사용한 hypergolic 방식을 사용하였다. 산화제 $61\%$, 연료 $67\%$를 공급하여 정상 연소압 대비 $63\%$인 33 abs.bar의 연소압으로 0.25 초 동안 pre-stage 구간을 유지하였다. 2단계의 점화과정을 통해 정상상태에 이르기까지 O/F ratio를 설계조건 보다 낮은 영역에 유지하였다. main-stage로 진입 시 압력피크는 정상 연소압의 $0.6\%$를 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1055-1062
• /
• 2004

As for the Production of internal combustion engines there has been further movement toward development of high Performance engines with improved fuel efficiency as well as a lightweight and a small size. These tendencies help to solve the problems in engines for example, such as thermal load. abnormal combustion and so on. In order to investigate these Problems, a thin film-type probe for measuring instantaneous temperature has been suggested. A method for manufacturing such a probe was established in this study The instantaneous surface temperature of a constant volume combustion chamber was measured by using this probe and the heat flux was obtained through Fourier analysis In order to thoroughly understand the characteristics of combustion. authors measured wall temperature of combustion chamber and calculated heat flux through a cylinder wall while varying the protrusion height of probe. For these Purposes, the instantaneous surface temperature probe was developed. thereby making possible the analysis of instantaneous temperature of wall surface and the detection of unsteady heat flux in the constant volume combustion chamber.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.305-308
• /
• 2005

본 논문은 30ton급 액체로켓엔진 연소기의 연소시험 검증용 제작에 관한 것이다. 기본설계와 상세설계를 통해 도면을 작성하고, 이에 따라 제작하였다. 연소기는 크게 헤드부와 챔버부로 구성되며, 챔버는 KSR-III에 적용되었던 내열재 챔버와 재생 냉각 방식의 챔버를 제작하였다. 연소기 헤드는 저온 특성이 좋은 SUS316L 재료를 사용하였다. 내열재 챔버는 내부는 silica/phenolic 재료를 사용하였고, 외부케이스는 SUS316L을 적용하였고, 재생 냉각 챔버는 C18200과 SUS316L 재료를 사용하였다. 선반 가공, 일반 밀링 가공, MCT 가공등의 기계적 가공을 한 후 전해 연마를 통해 이물질을 제거 하였다. 분사기와 분사기 플레이트의 접합과 재생 냉각 챔버 등 일부 부품의 접합은 구조적인 특성으로 인해 브레이징 기법을 적용하였다.

• Journal of Korean Society for Atmospheric Environment
• /
• 제14권E호
• /
• pp.41-58
• /
• 1998

In this study, a wide range of volatile organic constituents of environmental tobacco smoke (ETS) were determined using an environmental chamber, where ETS is the sole source of target compounds. ETS was generated in an environmental chamber by a number of different cigarettes, including the Kentucky reference cigarette and eight different commercial brands. More than 30 compounds were measured simultaneously for a total of twelve experimental runs. The target compounds are classified into three major classes, i.e. vapor phase ETS markers including 3-ethnylpyridine (3-EP) and nicotine, carbonyl compounds including formaldehyde, and volatile organic compounds (VOCs). The results from the chamber study were used to generate characterized ratios of selected VOCs to 3-EP, a vapor phase ETS marker. Emission factors for VOCs associated with ETS were also estimated. The characteristic ratios appeared to be generally in good agreement with published data obtained by environmental chamber studies similar to this study. This implies that the ratios may be useful for identifying and quantifying the impact of ETS as a source of target compounds in 'real world' indoor environments, which is affected by a complex mixture of multi-sources. The environmental chamber method described here provides a direct and reliable method to compare the ETS generated by different cigarettes. The method can also be applied to the simultaneous determination of many different ETS components.

• 한국산학기술학회논문지
• /
• 제3권4호
• /
• pp.233-239
• /
• 2002

21세기에 가장 시급하게 확보되어야 하는 기술은 BT(Biotechonolgy)와 NT(Nano technology)를 접목시키는 기술이다. 특히, 이들을 종합한 MEMS 에 관한 연구는 가장 광범위한 분야에서 활발하게 이루어지고 있어 그 기술적 가치가 점차 중요시되고 있다. 본 연구는 Simulation을 통하여 Bio-MEMS 기술에서 사용되는 미세Pump 내에서의 유체흐름을 Fluent 프로그램을 사용하여 알아보고자 하였다. 즉, 미세Pump 내로 유체가 흐를 경우, 유체의 압력변화나 온도변화 및 Model에 따른 유동의 흐름을 관찰하여 미세Pump 내에서의 최적의 외부조건과 최적의 Pump Model을 알아보고자 실험하였다. 유동의 흐름을 조사해 본 결과 Chamber의 유무에 따라 압력과 온도의 변화를 관찰할 수 있었다. Chamber가 있는 경우 압력의 변화가 적었고 온도의 변화 또한 적었다. 따라서 Chamber가 있는 Pump가 유체의 흐름에 영향을 적게 줌을 알 수 있었으며 이는 Chamber가 있는 Pump를 설계하는 것이 필요하다고 할 수 있다.

• Nuclear Engineering and Technology
• /
• 제38권5호
• /
• pp.455-458
• /
• 2006

The HANARO reactor has a vertical hole for a cold neutron source (CNS) in the heavy-water reflector tank, i.e., the CNS hole, which was considerably deformed during its welding to the horizontal cold neutron (CN) beam tube. This paper presents an investigation of the form of the CNS hole for the optimal design of the a vacuum chamber for the CNS. In addition, the installation method of the vacuum chamber into the CNS hole for minimizing the water thickness between the vacuum chamber and the nose of the CN beam tube is proposed.

• 설비공학논문집
• /
• 제4권1호
• /
• pp.57-64
• /
• 1992

A computer program was developed for the prediction of transient flow in a water supply system. where an air chamber is installed to reduce the water hammering. The governing equations based on a characteristic method are solved using a finite difference method. A design process of an air chamber is shown in the present paper considering the effects of the initial air volume and the discharge coefficients of the orifice on the total volume and over-all performance of the chamber.