• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.307-312
• /
• 2005

In this paper, the broadband FCMA(Folded Cross Monopole Antenna), which is the cross monopole antenna with the folded element, is presented. To investigate the broadband characteristics of FCMA the VSWR, the gain, and the radiation pattern are calculated in frequency between 1.75 GHz and 2.655 GHz. From the calculated result, it is shown that the presented folded cross monopole antenna has a excellent band characteristics than the existing cross monopole antenna. The presented antenna is conformed as a broadband antenna which can be used for the indoor antenna of PCS, WCDMA, Wibro, and satellite DMB band.

• Proceedings of the IEEK Conference
• /
• 2000.06a
• /
• pp.173-176
• /
• 2000

In This paper, a novel broadband monopole antenna is investigated experimentally. Our broadband monopole antenna yields the largest bandwidth from 1.72 ∼ 2.2 GHz ( 24.2 ％ ) for VSWR<1.2 So, this antenna can be designed to extend enough the coverage of dual band(PCS＋IMT-2000). The measurements and computations are confirmed to operating of the our broadband antenna, whose electrical characteristics have an attractive feature as handset communication applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.204-209
• /
• 2005

A small size broadband microstrip patch antenna with small ground plane has been fabricated using MEMS. Multiple layer substrates are used to realize small size and broadband characteristics. The microstrip patch is divided into 3 pieces and each patch is connected to each other using a metal microstrip line. The fabrication process is simple and only one mask is needed. Two types of microtrip antennas are fabricated. Type A is the micros trip antenna with metal lines and type B is the microstrip antenna without metal lines. The size of proposed microstip antenna is $8^{*}12^{*}2mm^{3}$ and the experimental results show that the antenna type A and type B have the bandwidth of 420 MHz at 5.3 GHz and 480 MHz at 5.66 GHz, respectively.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.5 no.1
• /
• pp.43-59
• /
• 2006

A compact and broadband $4\times1$ array antenna was developed for 3G smart antenna system testbed. The $4\times1$ uniform linear away antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% $(VSWR\leq1.5)$, 21.78% $(VSWR\leq2)$ with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.7 no.1
• /
• pp.41-58
• /
• 2007

A compact and broadband $4{\times}1$ array antenna was developed for 3G smart antenna system testbed. The $4{\times}1$ uniform linear array antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% ($VSWR{\leq}1.5$), 21.78% ($VSWR{\leq}2$) with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.210-213
• /
• 2001

In this paper, we analyzed the impedance characteristic of the bow-tie antenna for the broadband operation. The pulsed subsurface radar uses the impulse to collect information for subsurface objects, so the broadband antenna is used to minimize reflections in the feed point for the broadband characteristic of impulse. Therefore, in this paper we analyzed the broadband bow-tie antenna with Ensemble 5.0.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.227-233
• /
• 2011

This paper describes the development of a broadband quasi-Yagi antenna using a folded dipole driver. The antenna is designed on a low-permittivity substrate to reduce the surface wave effect, and hence the gain can be enhanced easily by adding directors. The folded dipole driver is connected to a 50-${\Omega}$ microstripline via a simple broadband microstrip-to-coplanar stripline transition with a quarter radial stub. The key motivation for the use of a folded dipole is to increase the input impedance at the driver, allowing a smaller mismatch loss between the antenna driver and the coplanar stripline feed. The proposed antenna has a measured bandwidth of 4.67~6.26 GHz for the -10 dB reflection coefficient, and a flat gain of 4.86~5.15 dB within the bandwidth.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.115-121
• /
• 2019

This paper presents the effects of the position of the split of a split-ring resonator (SRR) on the performance of a composite broadband printed dipole antenna. The antenna is made of two printed dipole arms enclosed by two rectangular and identically printed SRRs. One dipole arm and the SRR are printed on the top side of the substrate, while the other dipole arm and SRR are printed on the bottom side of the same substrate. By changing the position of the split on the SRR, different antenna characteristic values are obtained, namely, for impedance bandwidth and radiation patterns. The split position is thus a critical parameter in antenna design, because it influences the antenna's major performance immensely. Different split positions and their consequences for antenna performance are demonstrated and discussed. The antenna generates linearly polarized radiations, and it is computationally characterized for broadband characteristics. The optimized compact antenna has overall dimensions of 9.6 mm × 74.4 mm × 0.508 mm (0.06λ × 0.469λ × 0.0032λ at 1.895 GHz) with a measured fractional bandwidth of 60.31% (1.32 to 2.46 GHz for |S₁₁| <-10 dB) and a radiation efficiency of >88%.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.8
• /
• pp.87-92
• /
• 2004

In this paper, a microstrip slot antenna with a fork-shaped feedline is designed and fabricated. To obtain a broadband characteristic of a wide slot antenna a feedline is transformed into a shape of a fork, and a size of the slot and offset - length is varied. As the characteristics of the slot antenna as the function of design parameters are analyzed, a broadband microstrip slot antenna is designed. The microstrip slot antenna with a fork-shaped feedline is fabricated and its measured bandwidth is from 1.65 GHz to 6.20 GHz for VSWR$\leq$2.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.5
• /
• pp.135-141
• /
• 2020

This paper summarizes the data of a monopole antenna with a sleeve structure that can be applied in various ways. Sleeve monopole antennas have broadband characteristics and are used for multi-frequency applications. The sleeve monopole antenna is composed of a vertical conductor, which is a radiator, and a sleeve having the same structure as a coaxial cable. The sleeve acts as a radiator and an open stub. The length of the sleeve should be 1/3~2/3 of the total length of the antenna. A monopole antenna having a sleeve structure is applicable to a vehicle wiper antenna. In addition, the case of applying this antenna to a broadband sleeve antenna using a loading coil, a broadband printed sleeve monopole antenna for an ISM band, a gap sleeve and a double sleeve, and a UWB planar monopole antenna using half cutting was summarized and analyzed in terms of structure and broadband.