• 전기학회논문지P
• /
• 제50권3호
• /
• pp.117-124
• /
• 2001

The aim of this paper is to develop a controller of multi-phase bipolar brushless DC (MPB BLDC) motors for an electric bicycle. A MPB BLDC motor has a Permanent magnet rotor in which the magnetic arrangement is radial to the shaft and integral to the rotor laminations. This technique concentrates flux, giving a higher flux density than a surface-mounted PM motor and increases reluctance torque. The stator of MPB BLBC motor has parallel winding, allowing multi-phase separate independent controllability. It gets much more high power than wye-connection at same low voltage. The conventional techniques of exited with modulation(EWM), bidirection control, and partial square wale control are Proposed with one H-bridge and two photo sensors per phase. The Proposed controller is satisfied for the limited speed control and designed for system stability Experimental results show the performance of the proposed controller of MPB BLDC motors for an electric bicycle.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.465-470
• /
• 2001

Two-phase BLDC(brushless DC) motor has larger torque ripple than three-phase BLDC motor because of its unique skeleton-type structure. An electronic switching mechanism to change the current-direction of the BLDC motor can be a source of vibration as well as unbalanced rotor weight. A proper switching timing which makes less vibrations was considered by changing the position of sensing element around the center of rotation. Also, the current of the motor was measured for the calculation of the motor efficiency. From the vibration test results and with the consideration of the motor efficiency, an optimal switching position of the Hall sensor was found.

• 조명전기설비학회논문지
• /
• 제26권2호
• /
• pp.27-33
• /
• 2012

In this paper, we researched the heat transfer analysis of 1.2[kW] BLDC motor on the condition of the external flow. The BLDC motor is fallen under influence of some heat generated by rotationg motor speed and it changes the life and confidence of motor. The heat makes to reduce the life of insulation and the magnetization. So motor can't make own performance. Therefore we calculated the losses about number of revolutions of motor. And then, we analyzed the heat transfer of BLDC motor by using the results when a fan attached to motor makes the external flow or not. The results showed that the temperature of motor increased constant values irrespective of external air temperature. The temperature of motor decreased very lower values than prior researches when the fan makes the external flow. In this method we can analyze the performance, losses and heat transfer of motor applied in the many industries.

• 전기학회논문지P
• /
• 제55권2호
• /
• pp.62-66
• /
• 2006

This thesis focuses on the design of control schemes for highly efficient BLDC motor drive applications using drives with output capacity of 1Hp. The control system was designed and implemented on a PIC micro-controller and applied to an electric vehicle as a viable replacement to the existing a high phase induction motor that is currently being used for these low cost, small traction drive applications. This paper for the brushless drive research has shown the optimization of the drive system for improved drive design and switching techniques that can improve the entire drive system efficiency for electric vehicle both large and small traction applications using sinusoidal PWM techniques for synthesizing the AC waveforms needed to control these traction drives. In addition, Numerical simulation was conducted to evaluate the performance of designed BLDC Motor using MotorPro simulator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.388-390
• /
• 1999

This paper discusses an optimal design of high space factor BLDC motor. Because of high space factor BLDC, Nonliear finite element method considering saturation of outer-rotor is used. For optimal design, a new niching genetic algorithm, namely "Restricted Competitions Selection" is used. This algorithm constructs an objective function using only the most important criteria and provides a designer with a set of solution rather than one solution. To verify its effectiveness, the new niching genetic algorithm is applied to an actual high space factor BLDC motor We show that a new designed high space factor BLDC motor is superior to the actual high space factor BLDC.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.932-941
• /
• 2014

In this paper, a simulation model for 7-phase BLDC motor drives for an Autonomous Underwater Vehicles (AUV) is proposed. A 7-phase BLDC motor is designed and the electrical characteristics are analyzed using FEA program and the power electronics drives for the 7-phase BLDC motor are theoretically analyzed and the actual implementation has been accomplished using Matlab Simulink. PI controller and fuzzy controller are compared for verifying the validity of the proposed model and the informative results are described in detail. Especially A fuzzy controller is used to characterize 7-phase BLDC motor, drive systems under normal and fault operating conditions.

• 한국정보전자통신기술학회논문지
• /
• 제3권4호
• /
• pp.3-9
• /
• 2010

Brushless DC(이하 BLDC) 모터는 에너지절감 차원이나 속도 및 토크제어에 대한 우수성 때문에 그 활용이 점차 증가하고 있다. 그러나 다양한 환경의 응용분야에 따라 제어기 및 구동회로가 별도로 필요하고, 또 모터와는 별개로 외장형으로 설계되어 있어 설치 및 운용에 어려움이 있다. 본 논문에서는 유증기회수장치(VRS)용으로 BLDC모터와 제어회로가 일체화되도록 제작하였으며, 마이크로프로세서를 적용하여 다양한 주변 환경에 따른 지능적인 동작이 가능하도록 설계하였다. 또한 TCP/IP 모듈을 내장하여 원격지에서 웹을 통해 제어할 수 있도록 설계하여 작동의 편의성을 고려하였다.

• 한국전자통신학회논문지
• /
• 제14권5호
• /
• pp.1009-1018
• /
• 2019

본 연구에서는 표면근전도 측정기 기반의 재활의료기기의 설계 및 구현에 관한 내용을 기술한다. 재활시스템은 BLDC모터와 모터 드라이브를 이용하여 제어된다. BLDC모터 드라이브는 동작제어를 하며, 속도는 외부 서보모터를 통해 드라이브를 제어한다. 또한 모터 외부에 결합된 포텐쇼미터는 모터에 의해 회전하는 부하 위치 정보를 전달한다. 재활 알고리즘은 환자가 일정 각도 범위에서 주기적인 수축 이완 재활운동을 속도단계별로 실행하며 재활운동 시 사용자 설정 단계에 따른 모터를 활용하여 $0{\sim}120[^{\circ}]$의 최대각도로 제한하여 제어한다. 보행 알고리즘은 양쪽 안쪽넓은근에 부착된 표면근전도 측정기로 획득한 신호의 차이 값을 이용하여 근전도 신호가 낮은 다리에 모터제어로 보상해주며 보행운동 시 모터와 표면근전도 측정기를 활용하여 $0{\sim}88[^{\circ}]$의 최대각도로 제한하여 제어한다.

• 전력전자학회논문지
• /
• 제22권3호
• /
• pp.223-230
• /
• 2017

A low-cost BLDC motor with hall sensor is used to drive the position control of a facility security monitoring system in this paper. Low measurable frequency of the hall sensor signal in low-speed regions results in difficulty in obtaining accurate speed detection and position control. To improve system control performance, we propose a variable gain of position controller and stop mode control scheme according to the motor speed and error position with pre-set deceleration time. The proposed stop mode control scheme is activated around the stop position to forcibly move the BLDC motor to the stop position in low speed. In the proposed stop mode, the motor current is controlled by the actual speed with the reference rotating angle. The control performance of the proposed position control is verified through experiments at the actual rail guided facility security monitoring system.

• Journal of Electrical Engineering and Technology
• /
• 제8권2호
• /
• pp.295-303
• /
• 2013

This paper reports an investigation of pulse width modulation (PWM) techniques for two-phase brushless DC (BLDC) motors fed by a two-phase eight-switch inverter in a fan application. The three-phase BLDC motor is widely applied in industry; however, a lower-cost two-phase BLDC motor and drive circuit has been greatly in demand in recent years. In this paper, we introduce a mathematical model of the two-phase BLDC motor with sinusoidal back electromotive forces (EMFs) based on traditional three-phase BLDC motors. To simplify the drive algorithm and speed up its application, we analyze the principle of block commutation for a two-phase BLDC motor drive in the 180-electrical-degree conduction mode, and we further propose five PWM schemes to improve the commutation performance of the two-phase BLDC drive. The effectiveness of the proposed PWM methods is verified through experiments.