• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.21-27
• /
• 2011

The comparison work was conducted for the methanol steam reforming among commercial Cu-based catalysts, viz. ICI-M45, which is for the methanol synthesis, MDC-3 and MDC-7, which are for the water-gas shift reaction. The catalytic activity for the water-gas shift reaction was also compared over three catalysts. Among them, MDC-7 showed the highest methanol conversion and formation rate of hydrogen and carbon dioxide at 473 K for the methanol steam reforming. To find out any promotional effect between ICI-M45 and MDC-7, three different packing methods with these two catalysts were examined. However, no synergistic effect was observed. The catalytic activity for watergas shift reaction decreased in the following order: MDC-7 > MDC-3 > ICI-M45. The highest activity of MDC-7 for the methanol steam reforming as well as the water-gas shift reaction can be due to its high surface area, copper dispersion, and an adequate Cu/Zn ratio.

• Journal of Periodontal and Implant Science
• /
• v.24 no.3
• /
• pp.597-606
• /
• 1994

Oxygen derived radicals($O_2\;^-$, $H_2O_2$, and $OH^-$) are thought to play a role in a lot of human diseases. And it has been believed that antioxidant enzymes such as superoxide dismutase(SOD) and catalase could protect the tissues from damage resulting from the oxygen derived free radicals. The purpose of this study was performed to investigate the activity of the SOD(CuZn- and Mn-SOD) and catalase in inflammatory gingival tissues and the correlation between boold glucose level and antioxidants and age in non-insulin dependent diabetes mellitus(NI- DDM) patients. For this study, the patients were classified into normal, inflammatory, and diabetic, and ten their papillary bleeding index(PBI) and gingival index were checked. Subjects consisted of 11 healthy patients with no inflammatroy gingiva, 20 adult periodontitis patients, and 8 diabetic patients, aged 33 to 66(average: 44.62). The blood glucose level of diabetic group was ranged from 120ml/dl to 160ml/dl(physical status 0 : averge : 135.67ml/dl). Gingival tissues were surgically obtained from the patients during periodontal surgery, extraction, and clinical corwn lenghening procedure. The activity of CuZn and Mn- SOD and catalase in the gingival tissues was measured by using UV-spectrophotometer by the same methods that Crapo et al. And Aebi did, respectively. The results were as follows : 1. The Mn-SOD activity was significantly lower in inflammatory group in comparison to normal group(P<0.05), and the activities of antioxidants in diabetic group were not significant in comparison to normal inflammatory group(P>0.05). 2. The activities of antioxidants showed little variation among individuals of different ages (P>0.05). 3. The higher blood glucose level was, the higher gingival index was(P<0.05). 4. There was no correlation between blood glucoe level and activity of antioxidant in inflammatory gingival tissues of NIDDM patients(P>0.05). In conclusion, these results, within the limits of the present experiment, suggest that the activity of Mn-SOD might reflect the inflammatory status of gingival tissue, and the activity of antioxidants was independent of blood glucose level of diabetic patients in physical status 0.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.235-242
• /
• 2006

Liquid phase alkylation of biphenyl (BP) was studied over large pore zeolites. Selective formation of the least bulky products, 4,4'-diisopropylbiphenyl (4,4'-DIPB) occurred only in the isopropylation of BP over some large pore molecular sieves. H-mordenites (MOR) gave the highest selectivity among them. The dealumination of MOR enhanced catalytic activity and the selectivity of 4,4'-DIPB because of the decrease of coke-deposition. Non-selective catalysis occurs on external acid sites over MOR with the low $SiO_2/Al_2O_3$ ratio because severe coke-deposition deactivates the acid sites inside the pores by blocking pore openings. The selectivity of DIPB isomers was changed with reaction temperature. Selective formation of 4,4'-DIPB was observed at moderate temperatures such as $250^{\circ}C$, whereas the decrease of the selectivity of 4,4'-DIPB occurred at higher temperatures as $300^{\circ}C$. However, 4,4'-DIPB was almost exclusive isomer in the encapsulated DIPB isomers inside the pores even at high temperatures. These decreases of the selectivity of 4,4'-DIPB are due to the isomerization of 4,4'-DIPB on the external acid sites. Some 12-membered molecular sieves, such as SSZ-24, MAPO-5 (M:Mg, Zn, Si), SSZ-31, and ZSM-12, which have straight channels, gave 4,4'-DIPB with moderate to high selectivity; however; SSZ-55, SSZ-42, and MAPO-36 (M: Mg, Zn) gave lower selectivity because of cages in 12-membered one dimensional channels. Three dimensional H-Y and Beta zeolites also yield 4,4'-DIPB in low yield because of their wide circumstances for the isopropylation of BP. The increasing the size of alkylating agent enhanced the shape-selective alkylaiton even for the zeolites, such as UTD-1. The ethylation of BP to ethylbiphenyls (EBPs) and diethylbiphenyls (DEBPs) over MOR was non-selective. The ethylation of BP to EBPs was controlled kinetically. However, there was difference in reactivity of EBPs and DEBPs for their further ethylation. 4-EBP was ethylated preferentially among the isomers, although the formation of 4,4'-DEBP was less selective. The least bulky 4-EBP and 4,4'-DEBP have the highest reactivity among EBPs and DEBPs for the ethylation to polyethylbiphenyls (PEBPs). These results show that the environments of MOR pores are too loose for shape selective formation of the least bulky isomers, 4-EBP and 4,4'-DEBP in the ethylation of BP, and that MOR pores have enough space for the further ethylation of 4,4'-DEBP.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.11
• /
• pp.9-18
• /
• 2003

Two configurations of Film Bulk Acoustic Wave Resonators with acoustic quater-wave bragg reflector layers are theoretically analyzed using equivalent circuits and the difference of their characteristics are discussed. We compare the characteristics of λ/2 mode to those of ideal FBAR with top and bottom electrode contacting air and the characteristics of λ/4 mode to those of ideal FBAR with top electrode contacting air and bottom electrode clamped. We assume that the piezoelectric film is ZnO, the electrode is A1 and the substrate is Si, ABCD parameters are extracted and input impedance is calculated by converting the equivalent circuit from Mason equivalent circuits to the simplified equivalent circuits that ABCD parameters are extracted possible, From the variation of resonance frequency due to the change of thickness of reflector layers and the variation of electrical Q due to the change of mechanical Q of reflector layers, it is confirmed that the reflector layer just under the bottom electrode have the greatest effect on the varation of resonance frequency and electrical Q. It is shown that the number of reflector layers required for the saturation of electrical Q decreases with the increase of the impedance ratio of reflector layers and electrical Q of λ/2 mode is larger than that of λ/4 mode, Electromechanical coupling factor is independent of the number of layers, The impedance ratio of reflector layers becomes larger as the electromechanical coupling factor becomes larger, The electromechanical coupling factor of the two mode are smaller than those of ideal FBARs because of the trapping of acoustic energy in the reflector layers, The insertion loss of the ladder filter decreases with the increase of the number of reflector layers but the bandwidth is not affected much by the number of reflector layers, As the impedance ratio of reflector layers becomes larger the insertion loss becomes smaller and the bandwidth becomes wider, In our analysis of the two mode, characteristics of λ/2 mode appear to be slightly more favorable than that of λ/4 mode

• Natural Product Sciences
• /
• v.20 no.3
• /
• pp.160-169
• /
• 2014

44 compounds and 9 minerals were isolated from and detected in the New Zealand deer velvet antler Cervus elaphus var. scoticus L$\ddot{o}$nnberg. The chemical structures of (1 - 26) were identified on the basis of the spectroscopic methods and comparisons with literature, respectively. The structures were identified as cholesterol (CS, 6), 7-keto-CS (7), $7{\beta}$-hydroxy-CS (8), and $7{\alpha}$-hydroxy-CS (9), and included 12 steroid $3{\beta}$-O-(palmitic/stearic/myristic acid esters; PM/SA/MS) [CS-$3{\beta}$-O-PM (1 - 1), CS-$3{\beta}$-O-SA (1 - 2), CS-$3{\beta}$-O-MR (1 - 3), 7-keto-CS-$3{\beta}$-O-PM (2 - 1), 7-keto-CS-$3{\beta}$-O-SA (2 - 2), 7-keto-CS-$3{\beta}$-O-MR (2 - 3), $7{\beta}$-hydroxy-CS-$3{\beta}$-O-SA (3 -1), $7{\beta}$-hydroxy-CS-$3{\beta}$-O-PM (3 - 2), $7{\beta}$-hydroxy-CS-$3{\beta}$-O-MR (3 - 3), $7{\alpha}$-hydroxy-CS-$3{\beta}$-O-SA (4 - 1), $7{\alpha}$-hydroxy-CS-$3{\beta}$-O-PM (4 - 2), and $7{\alpha}$-hydroxy-CS-$3{\beta}$-O-MR (4 - 3)], dinonyl phthalate (5), 8 nucleic acids analogues [uracil (10), deoxyguanosine (11), deoxyuridine (12), uridine (13), deoxyadenosine (14), adenosine (15), inosine (16), and guanosine (17)], and the 9 free amino acids [L-phenylalanine (18), L-isoleucine (19), L-leucine (20), L-tyrosine (21), L-valine (22), L-proline (23), L-threonine (24), L-alanine (25), and L-hydroxyproline (26)]. Also, there are 8 kinds of amino acids [asparagine, serine, glutamine, glycine, histidine, arginine, methionine, and lysine], 2 sialic acids [N-acetylneuraminic acid (27), ketodeoxynonulosonic acid (28)], and 9 minerals [Na > K > Ca > Mg > Fe > Zn > B > Al > Cu] were detected from the autoaminoacid analyzer and ICP spectrometer, HPAEC-PAD/HPLC-FLD, respectively. 9 kinds of oxycholesterol-$3{\beta}$-O-fatty acid ester (2 - 1, 2 - 2, 2 - 3, 3 - 1, 3 - 2, 3 - 3, 4 - 1, 4 - 2, and 4 - 3) and 3 nucleic acids (12, 14, and 15) were isolated from the velvet antler for the first time. 6 kinds of steroids (7, 8, 9, 2 - 1, 3 - 1, and 4 - 1) were examined for their anti-proliferative effects against L1210, P388D1, K562, MEG-01, KG-1, MOLT-4, A549, HepG2, MCF-7, SK-OV-3, and SW-620 cancer cell lines. They showed anti-proliferative effects with $IC_{50}$ values of 0.06, 2.16, 2.42, > 50.0, 1.66 and $8.31{\mu}M$ against L1210, while the values were 24.05, 9.44, 5.22, 0.25. 9.48 and $49.77{\mu}M$ against P388D1, respectively. The others were inactive.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.194-195
• /
• 2012

박막 실리콘 태양전지에 입사한 빛 중 흡수층인 진성 비정질 실리콘층(i-a-Si)에 흡수된 빛은 출력으로 변환되나, 기타의 층에서 흡수된 빛은 손실 성분이 된다. 이 중 흡수 손실이 큰 층은 도핑 층(p-a-SiC 및 n-a-Si)들인데, 이 들의 흡수 손실을 측정된 광학함수를 이용해 계산해 보면 Fig. 1과 같이 나타난다. p-a-SiC은 광 입사부에 위치하여 단파장 영역의 흡수 손실을 일으키고, n-a-Si 은 태양전지의 후면에 위치하여 장파장 영역의 흡수손실을 일으킨다. 이러한 도핑층에서의 흡수 손실을 제거 또는 개선하기 위해 도핑층의 재료를 기존 재료보다 광학적 밴드갭이 큰 재료로 대체하여 개선하는 방안에 대해 논하고자 한다. 금속 산화물의 밴드갭은 실리콘 화합물에 비하여 대체로 큰 값을 가지기 때문에 이를 기존의 실리콘 화합물 대신으로 사용한다면 광학적 흡수 손실을 효과적으로 줄일 수 있다. 단, 이때 태양전지의 광 전압을 결정하는 인자가 p층과 n층 사이의 일함수 차이에 해당하므로, p층의 대체층으로 사용 가능한 금속 산화물은 일함수가 큰(＞5 eV) 재료 중에서 선택하는 것이 적합하며, n층의 대체층으로 사용 가능한 금속 산화물은 일함수가 작은(＜ 4.2 eV) 재료 중에서 선택하는 것이 적합하다. Table 1에서 p층과 n층 대체용 금속산화물의 후보들을 정리하였다. 먼저 도핑층에서의 광 흡수가 광손실이 될 수 밖에 없는 물리적 근거에 대해서 논하고, 그 실험적인 증명을 제시한다. 이러한 개념을 바탕으로 도핑층의 내부 전기장의 방향을 제어하여 전자-정공쌍을 분리 수집하는 방법을 실험적으로 구현하였다. 이어서 금속 산화물을 부분적으로 대체하여 흡수 손실을 개선하는 방안을 제시한다. WOx, NiOx, N doped ZnO 등을 적용하여 그 효과를 비교 검토하였다. 끝으로 금속산화믈 대체 또는 쇼트키 접합을 적용하여 도핑층의 광 흡수를 줄이고 효율을 향상하는 방안을 제시한다. 그 사례로서 WOx, MoOx, LiF/Al의 적용결과를 살펴보고 추가 개선방안에 대해 토의할 것이다. 결론적으로 광학적 밴드갭이 큰 재료를 도핑층 대신 사용하여 흡수 손실을 줄이는 것이 가능하다는 것을 알 수 있고, 이 때 일함수 조건이 만족이 되면 광 전압의 손실도 최소화할 수 있다는 점을 확인할 수 있었다. 현재까지 연구의 한계와 문제점을 정리하고, 추가 연구에 의한 개선 가능성 및 실용화 개발과의 연관관계 등을 제시할 것이다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.245-245
• /
• 2015

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. 특히 CIGS 태양전지에서는 Na의 역할이 매우 중요한데 유연기판의 경우 이러한 Na이 없을 뿐만 아니라 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 또한 플라스틱기판의 경우 내열성이 낮아 저온에서 공정을 진행해야하는 단점이 있다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 유연기판으로 STS 430 stainless steel과 poly-imide를 이용하여 특성 개선을 진행하였다. 먼저 stainless steel과 Poly-imide, soda-lime glass, coning glass의 기판을 이용하여 기판에 따른 흡수층의 특성을 비교 분석하였으며 stainless steel 기판을 이용하여 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 이때 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.6%로 증가하였다. 또한 poly-imide 기판을 이용하여 $400^{\circ}C$이하에서 흡수층을 제조하여 특성평가를 진행하였으며 소자 제조 후 효율은 약 12.2%를 달성하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.E1
• /
• pp.1-7
• /
• 2001

The elemental characteristics of atmospheric aerosols were investigated as a function of particle size and water solubility. The aerosol particles were samples at 12 individual size ranges between 0.01 and 30㎛. Collected aerosol particles were separated into both soluble and insoluble components. The concentrations of 15 elements in both components were determined by a PIXE analysis using a 2.0 MeV-proton beam. In general, the mass size distribution of particulate matter was represented as a bimodal distribution. The maximum rations of S in July and December were 5.5 and 3.8 %, and they appeared in the size range of 0.47∼1.17㎛(stage No. 6 or 7) . The ratios of a S at non-separated size were 3.1 and 2.2 % in July and December, respectively, On the other hand, the maximum rations of Si in July and December were 7.0 and 5.4% and they appeared in the size range of 5.1∼30㎛(stage No. 0∼2). The ratios of Si at the non-separated size were 2.1 and 1.8% in July and December, respectively, The mass diameter of 12 elements ranged between 0.59㎛ of S and 3.20 of Fe. More than 90% of atmospheric aerosols consisted of the light elements such as C, N, O, H and Al. The soluble component was dominant in the smaller size range and the insoluble component in the larger size range. Large portions of Si. Ti and Fe existed in insoluble state. By contrast, S, Cl, Ca, Zn and Br were dissolved in water.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.46 no.6
• /
• pp.930-940
• /
• 2013

We evaluated contamination with organic matter and trace metals by analyzing grain size, ignition loss (IL), chemical oxygen demand (COD), acid volatile sulfide (AVS), and trace metals (Al, Fe, Cu, Pb, Zn, Cd, Ni, Cr, Mn, Hg, and As) in surface sediments at 28 stations around the Geum River estuary in July 2008. The surface sediments in the estuary were mainly composed of coarse sediment (sand and muddy sand), with mean grain size (Mz) ranging between $2-4{\O}$. The high concentrations of IL, COD, and trace metals were mainly found at stations in front of the Gusan outer port and industrial complex, and near the Seocheon coast with relatively fine sediments. In addition, the concentrations of IL and all trace metals, except Pb and As, showed good positive correlations with Mz, indicating that the concentrations of organic matter and trace metals were mainly dependent on sediment grain size. The concentrations of COD, AVS, and trace metals in most sediments did not exceed the sediment quality guideline (SQGs). Although the sediments in the study region are not polluted with organic matter and trace metals, there are many point sources of pollutants, such as Gusan port and industrial complex, Janghang refinery, and a thermoelectric power plant around the Geum River estuary. Thus, the management of coastal environments through periodic monitoring of organic matter and trace metals is required in the future.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.10a
• /
• pp.64-67
• /
• 2006

RF 스퍼터링법을 이용하여 AZO(Al 2wt%, ZnO 98wt%)박막을 glass위에 증착한 후 증착 시간과 증착 압력에 따른 면저항, roughness 및 광투과도를 조사하였다. 본 연구에서 AZO박막의 면 저항은 4-point probe(Guardian, 402S)으로 측정하였으며 광투과도는 IR-VIS-UV spectrophotometer로 측정하였다. AZO 박막을 20분 증착하는 동안, 아르곤 flow양이 50, 100, 150sccm일 때 면저항은 $20\;{\Omega}/{\square}$이고, 200sccm일 때 $3744\;{\Omega}/{\square}$였다. AZO 박막의 두께를 일정하게 증착하는 동안, 아르곤 flow양이 50sccm일 때 면저항은 $49.6\;{\Omega}/{\square}$이고 100, 150, 200sccm일 때 $38{\Omega}/{\square}$였으며, 광투과도는 모두 80%이상을 보였다. Roughness는 각각 4.1nm, 7.6nm, 5.2nm, 16.9nm였다.