• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.597-602
• /
• 2015

Characteristics of continuous preparation of ZnO powder were investigated in a micro drop/bubble fluidized reactor of which diameter and height were 0.03 m and 1.5 m, respectively. The flow rate of carrier gas for transportation of precursors to the reactor was 6.0 L/min and the concentration of Zn ion in the precursor solutions was 0.4 mol/L, respectively. Effects of reaction temperature (973 K~1,273 K) and flow rate of micro bubbles (0~0.4 L/min) on the pore characteristics of prepared ZnO powder were examined. The optimum reaction temperature for the maximum porosity in the ZnO powder was 1,073 K within this experimental condition. The mean size of ZnO powder prepared continuously in the reactor decreased but the surface of the powder became smooth, with increasing reaction temperature. The injection of micro bubbles into the reactor could enhance the formation of pores in the powder effectively, and thus the mean BET surface area could be increased by up to 58%. The mean size of prepared ZnO powder was in the range of $1.25{\sim}1.75{\mu}m$ depending on the reaction temperature.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.4
• /
• pp.249-252
• /
• 1993

Water culture studies were conducted in the greenhouse with mulberry plants to investigate the nutrient uptake, especially Zn and Cu, under high phosphrous concentration. Mulberry plants were grown with five phosphorus levels(0, 0.2, 0.5, 2.0, 5.0 mM). Leaves and roots were analyzed for water content, total nitrogen, P, K, Ca, Mg, Fe, Mn, total Zn, soluble Zn, Cu, Cl, $NO_3HPO_4$ and $SO_4$. Dry matter increased upto 2.0mM phosphorus level, and then decreased. Water content, total nitrogen, P, K, and Fe in leaves increased with increasing phosphorus level. Total Zn content in leaves showed little change, whereas soluble Zn increased and Cu decreased with increasing phosphorus level. With increasing phosphous level. $SO_4$ and Cl decreased and then sharply increased above 2.0mM phosphorus. Lower uptake of Cu and higher uptake of $SO_4$ and Cl suggest a cause of mulberry yield decline with high accumulation of soil phosphorus.

• Korean Journal of Materials Research
• /
• v.15 no.9
• /
• pp.604-607
• /
• 2005

Dependence of the crystallinity, surface roughness, carrier concentration, carrier mobility, electrical resistivity and transmittance of Al-doped ZnO films deposited on glass substrates by RF-magnetron sputtering on effects of the ratio of the RF power for AlZnO to that for ZnO (R) have been investigated. X-ray diffraction spectra show strong preferred orientation along the c-axis. The full width at half maximum (FWHM) of the ZnO (002) peak decreases slightly as R increases in the range of R<1.0, whereas it increases substantially in the range of R>1.0. Scanning electron micrographs (SEM) show that the ZnO film surface becomes coarse as R increases. The carrier concentration and the carrier mobility in the ZnO thin film are maximal for R=1.5 and 1.0, respectively. The electrical resistivity is minimal for R=1.0 The transmittance of the ZnO:Al film tends to increase, but to decrease slightly in the range of R>0.5. It may be concluded that the optimum R value is 1.0, considering all these analysis results. The cause of the changes in the structure and physical properties of ZnO thin films with R are also discussed.

• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.98-103
• /
• 2013

$Mg_{3-x}Zn_xSb_2$ powders with x = 0-1.2 were fabricated by mechanical alloying in a planetary ball mill with a speed of 350 rpm for 24 hrs and then hot pressed under a pressure of 70 MPa at 773 K for 2 hrs. It was found that there were systematic shifts in the X-ray diffraction peaks of $Mg_3Sb_2$ (x = 0) toward a higher angle with increasing Zn for both the powder and the bulk sample and finally the phase of $Mg_{1.86}Zn_{1.14}Sb_2$ was formed at the Zn content of x = 1.2. The $Mg_{3-x}Zn_xSb_2$ compounds had nano-sized grains of 21-30 nm for the powder and 28-66 nm for the hot pressed specimens. The electrical conductivity of hot pressed $Mg_{3-x}Zn_xSb_2$ increased with increasing Zn content and temperature from 33 $Sm^{-1}$ for x = 0 to 13,026 $Sm^{-1}$ for x = 1.2 at 323 K. The samples for all the compositions from x = 0 to x = 1.2 had positive Seebeck coefficients, which decreased with increasing Zn content and temperature, which resulted from the increased charge carrier concentration. Most of the samples had relatively low thermal conductivities comparable to the high performance thermoelectric materials. The dimensionless figure of merit of $Mg_{3-x}Zn_xSb_2$ was directly proportional to the Zn content except for the compound with Zn = 1.2 at high temperature. The $Mg_{3-x}Zn_xSb_2$ compound with Zn = 0.8 had the largest value of ZT, 0.33 at 723 K.

• Journal of the Korean Vacuum Society
• /
• v.16 no.4
• /
• pp.286-290
• /
• 2007

We fabricated NiO coated ZnO nanorods using ZnO nanorods grown on a Si substrate. After thermal hydrogenation process of these NiO-ZnO core-shell nanorods, we confirm that Ni nanodots were built up on the surface of ZnO nanorods. Photoluminescence (PL) measurements at T=5 K were made to understand the optical properties of these various nanorods. As samples sequencially transformed into $ZnO{\rightarrow}NiO-ZnO{\rightarrow}Ni$ nanodot-ZnO, PL transition energies and intensities are varied as well. In comparison to pure ZnO nanorod, the acceptor bound exciton ($A^0X$) became the minor peak for NiO-ZnO nanorods. On the other hand, for Ni nanodot-ZnO sample, ($A^0X$) transition peak intensity became the most dominant peak. This is due to the fact that during thermal hydrogenation process, appreciable amounts of Ni and hydrogen ions defused into ZnO nanorod which played as accepters.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.166-166
• /
• 2012

We examined the distribution of Co ions of ferromagnetic n-type Zn(1-x)Co(x)O semiconducting films with the Co concentrations of 0.03~0.07 using x-ray absorption fine structure (XAFS) measurements at the Co and Zn K edges. Extended XAFS (EXAFS) revealed that Co ions mainly occupied the zinc sites of the films. X-ray absorption near edge structure (XANES) spectra demonstrated that the pre-edge peak of the Co K edge was substantially affected by the second neighboring Co ions at the zinc sites due to hybridizing of the Co 4p conduction electrons with the Co 3d bounded electrons. From XANES and EXAFS analysis using ab initio calculations, we found that Co ions uniformly occupied the zinc sites of the Zn (0.93) Co (0.07)O film, whereas the Co ions of the Zn (0.97) Co (0.03)O and Zn (0.95) Co (0.05)O films were substituted at localized zinc sites. The ferromagnetic properties of the Zn (0.93) Co(0.07)O film could be induced by direct interaction between the magnetic dipoles of the Co ions with a mean distance of 4.3 A or by Co 4p electron mediation.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.365-368
• /
• 2003

Small amounts of additives such as mol % 0.13 NiO and mol % 0.01 $CaCO_3$were added to Cu-Zn-Mg ferrites. Basic composition of the Cu-Zn-Mg ferrites was $Cu_{Cu}$X/$Fe_{0.054}$ /$Zn_{0.486}$$Mg_{0.407}$ $Fe_{1.946}$ $O_4$(group A) and $Cu_{0.263}$$Fe_{0.027}$ $Zn_{0.503}$ $Mg_{0.262}$ $Fe_{1.973}$ $O_4$(group B). Specimens were sintered at different temperatures (1010, 1030, $1050^{\circ}C$) for 2 hours in air followed by an air cooling. Then, effects of various composition and sintering temperatures on the microstructure and the magnetic properties such as inductions, coercive forces, and initial permeabilities of the Cu-Zn-Mg ferrites were investigated. The average grain size increased with the increase of sintering temperature. The magnetic properties obtained from the aforementioned Cu-Zn-Mg ferrite specimens were 1,724 gauss for the maximum induction, 1.0 oersted for the coercive force, and 802 for the initial permeability. These magnetic properties indicated that the specimens could be utilized as the core of IFT (intermediate frequency transformer) and antenna in the amplitude modulation.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.1
• /
• pp.189-196
• /
• 2014

Water dispersible ZnS based nanocrystals: ZnS (blue), ZnS:Cu (green) and ZnS:Mn (yellow-orange) were synthesized by capping the surface of the nanocrystals with a mercaptopropionic acid (MPA) molecule. The MPA capped ZnS based nanocrystal powders were characterized by using XRD, HR-TEM, EDXS, FT-IR, and FT-Raman spectroscopy. The optical properties of the colloidal nanocrystals were also measured by UV/Vis and photoluminescence (PL) spectroscopies in aqueous solvents. The PL spectra showed broad emission peaks at 440 nm (ZnS), 510 nm (ZnS:Cu) and 600 nm (ZnS:Mn), with relative PL efficiencies in the range of 4.38% to 7.20% compared to a reference organic dye. The measured average particle sizes from the HR-TEM images were in the range of 4.5 to 5.0 nm. White light emission was obtained by mixing these three nanocrystals at a molar ratio of 20 (ZnS):1 (ZnS:Cu):2 (ZnS:Mn) in water. The measured color coordinate of the white light was (0.31, 0.34) in the CIE chromaticity diagram, and the color temperature was 5527 K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.378-382
• /
• 1999

저 전압용 형광체는 최근에 활발히 연구가 진행되고 있으며 가장 대표적인 형광체가 ZnO Zn 녹색 형광체이다. ZnO : Zn 형광체는 자체발광형 형광체로써 ZnO을 환원분위기 하에서 열처리를 함으로써 얻을 수 있다. 본 연구에서는 자발착화 연소반응법(Glycine Nitrate Process)을 이용하여 ZnO : Zn 분말을 합성하고 형광특성 및 분말특성을 알아보았다. 출발물질로는 Zn Nitrate와 Glycine을 이용하였고 자발연소 반웅이 발생하는데 적절한 글리신의 양을 확인하기 위해서 글리신과 양이온의 비를 변화시키며 ZnO를 합성하였다. 그리고 Zn Excess가 생겨난 앙과 그에 따른 형광특성을 관찰하기 위해 $N_2$ 분위기 에서 각기 50$0^{\circ}C$, 75$0^{\circ}C$, 95$0^{\circ}C$의 온도에서 열처리를 행하였다. 제조된 ZnO 분말의 입자형태와 결정상 태는 SEM과 XRD를 이용하여 분석하였고 TG-DTA를 측정하여 열처리온도에 따른 질량감소(Zn excess)를 관찰하였다. 또 Particle size analyzer로 분말의 크기를 알아보았고 형광체로써의 발광특성을 살펴보기 위해 PL을 이용하여 발광피크를 관찰하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.5
• /
• pp.243-249
• /
• 2007

The age hardening behavior and mechanical properties of an extruded Al-Zn-Mg-(Cu)-0.1 wt.%Sc alloy were investigated with the Sc addition and ageing temperature. The results showed that the $Al_3Sc$ compounds were formed by Sc addition and distributed preferentially along the extrusion direction. The age hardening of Al-Zn-Mg-Cu-0.1 wt.%Sc alloy which was treated by T6 process was more significant than that of Al-Zn-Mg-0.1 wt.%Sc alloy. The tensile property of Al-Zn-Mg-Cu+0.1 wt.%Sc alloy was also higher than that of Al-Zn-Mg-0.1 wt.%Sc alloy, which is 691 MPa and 584 MPa in strength and 9% and 11% in elongation, respectively.