• Korean Journal of Materials Research
• /
• v.28 no.4
• /
• pp.214-220
• /
• 2018

We report on the fabrication and photoelectrochemical(PEC) properties of a $Cu_2O$ thin film/ZnO nanorod array oxide p-n heterojunction structure with ZnO nanorods embedded in $Cu_2O$ thin film as an efficient photoelectrode for solar-driven water splitting. A vertically oriented n-type ZnO nanorod array was first prepared on an indium-tin-oxide-coated glass substrate via a seed-mediated hydrothermal synthesis method and then a p-type $Cu_2O$ thin film was directly electrodeposited onto the vertically oriented ZnO nanorods array to form an oxide semiconductor heterostructure. The crystalline phases and morphologies of the heterojunction materials were characterized using X-ray diffraction and scanning electron microscopy as well as Raman scattering. The PEC properties of the fabricated $Cu_2O/ZnO$ p-n heterojunction photoelectrode were evaluated by photocurrent conversion efficiency measurements under white light illumination. From the observed PEC current density versus voltage (J-V) behavior, the $Cu_2O/ZnO$ photoelectrode was found to exhibit a negligible dark current and high photocurrent density, e.g., $0.77mA/cm^2$ at 0.5 V vs $Hg/HgCl_2$ in a $1mM\;Na_2SO_4$ electrolyte, revealing an effective operation of the oxide heterostructure. In particular, a significant PEC performance was observed even at an applied bias of 0 V vs $Hg/HgCl_2$, which made the device self-powered. The observed PEC performance was attributed to some synergistic effect of the p-n bilayer heterostructure on the formation of a built-in potential, including the light absorption and separation processes of photoinduced charge carriers.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.205-211
• /
• 2012

We investigated the optical and hydrophobic properties of the deposited silver (Ag) zinc oxide (ZnO) nanorods (NRs) on flexible indium tin oxide (ITO) coated polyethylene terephthalate (PET) substrates (i.e., ITO/PET). The ZnO NRs were grown by an electrochemical deposition using a sputtered ZnO seed layer and the Ag was deposited by using a thermal evaporator. For comparison, the same fabrication process was carried out on the bare ITO/PET without ZnO NRAs. Due to the discrete surface of ZnO NRs, the deposited Ag was formed as nano-scale particles, while the Ag became film-like for bare ITO/PET. In order to control the size and amount of Ag particles, the Ag deposition time was changed from 100 to 600 s. When the deposition time was increased, the Ag particles became larger and denser, and the absorptance was increased. This enhanced absorptance may be due to the localized surface plasmon resonance of Ag particles. Furthermore, the relatively high hydrophobicity was observed for the deposited Ag on the ZnO NRs/ITO/PET. These improved optical and surface properties are expected to be useful for flexible photovoltaic and optoelectronic devices.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.1-4
• /
• 2000

The Bis(8-oxyquinolino) zinc lII (Znq2) were synthesized successfully from zinc chloride $(ZnCl_2)$ as a initial material . The organic electroluminescece devices (ELDs) were fabricated with N-N'-diphenyl-N-N'-bis (3-meth-ylphenyl)-1,1'-biphenyl-4,4'-diamine (TPD) which act as a hole transporting layer and the Znq2 act as an EL emitting layer and electron transporting layer. In order to maximize luminance of ELD, TPD/Znq2/Al were deposited onto cleaned indium tin oxide (ITO) by changing thickness of EL emitting layer. The photoluminescence (PL) results show that Znq2 compound emits yellow green from 540nm. electrochemical behavior with V-J and V-L curve of carrier injection was investigated from 6 V. respectively. The maximum luminance were defected about $838 cd/m^2$. From these results, ai synthesized Znq2 material maybe one of the useful material of organic EL display material.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.473-473
• /
• 2013

전자종이, 입을 수 있는 디스플레이, 플렉서블 터치 스크린, 투과성 면 등과 같은 차세대 플렉서블 투명 전자소자는 기계적으로 유연하고 광학적으로 투명하며 무게가 가벼운 특성을 지녀야 할 것으로 예상된다. 현재까지는Indium tin oxide (ITO), zinc tin oxide (ZTO), carbon nano tube (CNT)와 polyimide 계열의 물질들이flexible, wearable, and transparent electronics (FWTEs) 소자의 electrode, active channel, dielectric layers로 제안되어 활발히 연구되었다. 최근에는 높은 이동도(~200,000 cm2/Vs) 및 유연성(fracture strain of 30%), 투명도 (97.5% for monolayer)와 같은 특성을 갖는 그래핀에 대한 연구가 활발히 진행되고 있다. 그러나 그래핀을 차세대 플렉서블 투명 전자소자 구현에 적용하기 위해서는 플렉서블하고 투명한 절연체의 확보 및 그래핀의 진성(intrinsic) 특성 유지 등과 같은 문제점들을 해결해야 한다. 따라서, 본 연구팀에서는 그래핀 기반 플렉서블 투명 전자소자의 게이트 절연층으로 적합한 poly-4-vinylphenol/poly (melamineco-formaldehyde) (PVP/PMF) 물질을 제시하고 이에 대한 전기적 재료적 분석을 수행하였다. 특히 다양한 PVP와 PMF의 비율 및 가열(annealing 혹은 curing) 온도에서 형성된 PVP/PMF 층의 화학 및 전기적 특성을 FT-IR, I-V, 그리고 C-V 측정을 통해 확인하였다. PVP/PMF는 유기절연 물질의 하나로서 높은 유연성과 투명도를 갖고 있을 뿐만 아니라 그래핀에 적용 시 그래핀의 진성 특성을 확보할 수 있다. 이는 PVP/PMF에 존재하는 hydroxyl (-OH) 그룹과 그래핀 상에서 정공(hole)을 공급하는 것으로 알려져 있는 -OH 그룹들간의 cross-linking 메커니즘에 의한 것으로 예상된다. 마지막으로 최적화된 PVP/PMF (낮은 hysteresis 전압)를 게이트 절연층에 적용하여 polyethylene terephthalate (PET) 기판 및 연구원의 손가락 위에 95.8%의 투명도 및 0에 가까운 Dirac point를 갖는 그래핀 기반 플렉서블 투명 전자소자를 성공적으로 집적하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.168-168
• /
• 2010

Transparent conduction oxides (TCOs) films is extensively reported for optoelectronic devices application such as touch panels, solar cells, liquid crystal displays (LCDs), and organic light emitting diodes(OLEDs). Among the many TCO film, indium tin oxide(ITO) is in great demand due to the growth of flat panel display industry. However, indium is not only high cost but also its deposits dwindling. Therefore, many studies are being done on the transparent conductive oxides(TCOs). We fabricated a target of IZTO(In2O3:ZnO:SnO2=70:15:15 wt.%) reduced indium. Then, IZTO thin films were deposited on glass substrates by pulsed DC magnetron sputtering with various oxygen flow ratio. The substrate temperature was fixed at the room temperature. We investigated the electrical, optical, structural properties of IZTO thin films. The electrical properties of IZTO thin films were dependent on the oxygen partial pressure. As a result, the most excellent properties of IZTO thin films were obtained at the 3% of oxygen flow rate with the low resistivity of $7.236{\times}10^{-4}{\Omega}cm$. And also the optical properties of IZTO thin films were shown the good transmittance over 80%. These IZTO thin films were used to fabricated organic light emitting diodes(OLEDs) as anode and the device performances studied. The OLED with an IZTO anode deposited at optimized deposition condition showed good brightness properties. Therefore, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.108-108
• /
• 2009

ITO에 사용되는 주된 재료인 인듐의 bixbyite 구조는 TCOs의 전기적 특성에서 매우 중요한 것으로 알려져 있다. 때문에 인듐의 Bixbyite구조를 유지하면서 인듐의 사용량을 줄이기 위해 최적의 Solubility limit에 관해 연구하였다. 이를 위해 In2O3-ZnO-SnO2의 삼성분계 기본 조성에 두가지 물질을 추가로 첨가하여 첨가량에 따른 Solubility limit을 연구하였다. Solubility limit의 측정을 위해 X-ray Diffractometer(XRD)를 사용하였으며, 첨가 원소의 양이 증가할수록 TCOs target의 Latice parameter값은 작아졌다, SEM을 통한 미세구조의 관찰로 원소첨가에 따른 샘플의 소결에너지 변화를 분석할 수 있었다. 제작된 시편의 정성분석 및 Chemical binding Energy를 측정하기 위해 X-ray Photo Spectroscopy (XPS)를 이용하였으며, 전기적인 특성 측정을위해 4-Point prove mesurement 방법을 사용하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.207-208
• /
• 2012

GZO( Ga-doped ZnO) 및 ZTO (zinc tin Oxide) 박막을 DC, RF magnetron sputtering 공정을 이용하여 증착한 후, 대기 및 진공상태에서 200, $300^{\circ}C$ 조건으로 30분 동안 열처리하였다. ZTO/GZO 박막의 전기적 특성은 ZTO 층과 GZO 층의 두께 비에 의존함을 확인 할 수 있었다. 본 연구에서는 GZO단일 박막과 ZTO/GZO double layer 박막의 열처리 온도에 따른 구조적, 전기적, 광학적 특성을 비교검토 하였다.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.2
• /
• pp.99-102
• /
• 2015

Thin film transistors (TFTs) with amorphous 2 wt% silicon-doped zinc tin oxide (a-2SZTO) channel layer were fabricated using an RF magnetron sputtering system, and the effect of post-annealing treatment time on the structural and electrical properties of a-2SZTO systems was investigated. It is well known that Si can effectively reduce the generation of oxygen vacancies. However, it is interesting to note that prolonged annealing could have a bad effect on the roughness of a-2SZTO systems, since the roughness of a-2SZTO thin films increases in proportion to the thermal annealing treatment time. Thermal annealing can control the electrical characteristics of amorphous oxide semiconductor (AOS) TFTs. It was observed herein that prolonged annealing treatment can cause bumpy roughness, which led to increase of the contact resistance between the electrode and channel. Thus, it was confirmed that deterioration of the electrical characteristics could occur due to prolonged annealing. The longer annealing time also decreased the field effect mobility. The a-2SZTO TFTs annealed at 500℃ for 2 hours displayed the mobility of 2.17 cm²/Vs. As the electrical characteristics of a-2SZTO annealed at a fixed temperature for long periods were deteriorated, careful optimization of the annealing conditions for a-2SZTO, in terms of time, should be carried out to achieve better performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.976-985
• /
• 2002

The purpose of this paper is that the roughness(Rrms = 31$\AA$, Rp-v = 270$\AA$) of ITO thin film deposited by sputtering method for OELD is improved to Rrms $\leq$ 10$\AA$, Rp-v $\leq$ 80$\AA$ by chemical mechanical polishing(CMP). First, ITO thin films are polished with a variety of consumables (Pads, Slurries) to choose proper some for the roughness improvement and the CMP mechanism of ITO thin films is demonstrated on the ground of the experiment results. Henceforth, the CMP characteristics (Removal rate, Non-uniformity) of chosen consumables are evaluated according to processing conditions (Polishing pressures, Table velocities) and suitable conditions for ITO film CMP are selected. Finally, the electrical and optical properties (Sheet resistance, Transmittance) of ITO thin films are investigated to verify whether or not ITO thin film are still suitable for OELD after polished.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.422-422
• /
• 2012

투명전극 산화막은 태양전지, 평판 디스플레이 등의 투명전극과 같은 광전자 소자에 사용되고 있다. 투명 전도성 산화막으로서 ITO (Indium tin oxide)는 높은 투과도, 낮은 비저항, 높은 일함수 등의 장점을 가지고 있어서 그동안 널리 사용되어 왔다. 그러나 In의 희소성으로 인한 고가격 문제 때문에 이를 대체하기 위해 불순물을 도핑한 ZnO (Zinc oxide)에 관한 연구가 활발히 진행되어 왔다. ZnO의 전기전도도를 높이기 위해 일반적으로 Al, Ga, B와 같은 3족 원소가 ZnO의 n형 도펀트로 널리 사용된다. 그 중에서 Al은 반응성이 커서 박막 증착 중에 산화되기 쉬운 반면 낮은 생산단가, 우수한 전기적 및 광학적 특성을 보이기 때문에 투명 전극으로서 Al-doped ZnO (AZO)가 많이 이용되고 있다. 본 연구에서는 rf 마그네트론 스퍼터링 공정을 이용하여 glass 기판 위에 Al-doped ZnO (AZO) 투명 전도막을 증착하였고, 수명 및 신뢰성에 영향에 미치는 주요 인자로서 온도, 온도 사이클 및 습도에 따른 AZO 박막의 열화 특성에 대한 연구를 진행하였다. 또한, 온도 사이클, 고온 및 고온고습 환경에 장시간 노출된 AZO 박막들의 성능 저하 원인들을 미세구조 관찰, 전기적 및 광학적 특성 변화들을 연계하여 규명하고자 하였다.