• Journal of Preventive Medicine and Public Health
• /
• v.26 no.1 s.41
• /
• pp.110-125
• /
• 1993

This study was designed to determine whether non-violent criminal and normal control on the basis of concentration of levels of trace mineral and toxic metal by analysis of human scalp hair. The subjects were selected 87 nonviolent criminal from a prison population and 120 normal control from periodic health checks for study. Hair samples were taken from the napes and Minnesota Multiple Personality Inventory (MMPI) was performed also. Five trace mineral (Zn, Cu, Mg, Fe, Na) and two toxic metal (lead, cadmium) contents were determined by an atomic absorption spectrometer. The contents of zinc and magnesium in hair of non-violent criminal were significantly lower than the control group (p<0.01). In the case of lead and cadimum, mean value of criminal group was significantly higher than control group. Significantly higher T-score of MMPI was seen in non-violent criminal group fur psychopathic deviate (Pd), paranoia scale (Pa), and Mania scale (Ma) than control group, but T-score of depression scale (D) was significantly higher in the control group. In the non-violent criminal group, the content of copper inversely proportion to T-score of Hs, D, Hy, Pd, Mf, Pa, Pt, Sc, Si except Ma, also Zinc inversely proportion to T-score of Hy, Mf, Pa, Pt. These results suggest that difference of some hair mineral contents exist between criminal and normal control group. Thus further studies are necessary to determine whether violent and nonviolent criminal group attributed biochemical imbalance with carefully constructed and controlled studies.

• Journal of Food Hygiene and Safety
• /
• v.35 no.5
• /
• pp.489-494
• /
• 2020

A total of 101 samples of convenience baby food products were analyzed by microwave digestion and mineral nutrients (iron, zinc, calcium, magnesium) were determined by inductively coupled plasma optical emission spectroscopy (ICP-OES). By type, the samples included 44 rice porridges, 40 soft-boiled rices, 11 purees, and 6 powders. The mean values for iron (Fe) content were 0.05 to 0.45 mg/100 g (excepted powder type, mg/l0 g). This was equivalent to 22.35% for rice porridge, 10.55% for soft-boiled rice, 9.88% for puree and 2.74% for powder type compared to the KDRIs (Dietary Reference Intakes for Koreans), respectively. The mean values for zinc (Zn) was 0.06 to 0.28 mg/100 g (excepted powder type, mg/l0 g) and the KDRI ratio was the lowest at 5.94% in puree, with 27.76%, 28.95% and 10.91% in rice porridge, soft-boiled rice and powder type, respectively. Calcium (Ca) content relative to KDRIs was relatively low compared to other minerals, with 6.65% for rice porridge, 3.61% for soft-boiled rice, 6.24% for puree and 3.07% for powder type, respectively. The magnesium (Mg) content of baby food ranged from 13.4% to 39.0% compared to KDRIs, and was included in all baby food as a whole. For balanced nutritional mineral supply to infants, it is recommended that information on mineral sources and ingredients in convenience baby food be clearly provided to ensure proper growth and development.

• Journal of the Korean Society of Radiology
• /
• v.13 no.4
• /
• pp.581-588
• /
• 2019

MRI is superior when contrasted to help the organization generate artifacts resolution, but also affect the diagnosis and create a image that can not be read. Metal is inserted into the tooth, it is necessary to often be inhibited in imaging by causing the geometric distortion due to the majority and if the difference between the magnetic susceptibility of a ferromagnetic material or paramagnetic reducing them. The purpose of this study is to conduct a metal artefact in accordance with the analysis using a diamagnetic material. The magnetic material include a wire for the orthodontic bracket and a stainless steel was used as a diamagnetic material was used copper, zinc, bismuth. Testing equipment is sequenced using 1.5T, 3T was used was measured using a SE, TSE, GE, EPI. A self-produced phantom material was used for agarose gel (10%) to a uniform signal artifacts causing materials are stainless steel were tested by placing in the center of the phantom and cover inspection of the positive cube diamagnetic material of 10mm each length.After a measurement artefact artifact zone settings area was calculated using the Wand tool After setting the Low Threshold value of 10 in the image obtained by subtracting images, including magnetic material from a pure tool phantom images using Image J. Metal artifacts occur in stainless steel metal artifact reduction was greatest in the image with the bismuth diamagnetic materials of copper and zinc is slightly reduced, but the difference in degree will not greater. The reason for this is thought to be due to hayeotgi offset most of the susceptibility in bismuth diamagnetic susceptibility of most small ferromagnetic. Most came with less artifacts in image of bismuth in both 1.5T and 3T. Sequence-specific artifact reduction was most reduced artifacts from the TSE 1.5T 3T was reduced in the most artifacts from SE. Signal-to-noise ratio was the lowest SNR is low, appears in the implant, the 1.5T was the Implant + Bi Cu and Zn showed similar results to each other. Therefore, the results of artifacts variation of diamagnetic material, magnetic susceptibility (${\chi}$) is the most this shows the reduced aspect lower than the implant artificial metal artifacts criteria in the video using low bismuth susceptibility to low material the more metal artifacts It was found that the decrease. Therefore, based on the study on the increase, the metal artifacts reduction for the whole, as well as dental prosthesis future orthodontic materials in a way that can even reduce the artifact does not appear which has been pointed out as a disadvantage of the solutions of conventional metal artifact It is considered to be material.

• Economic and Environmental Geology
• /
• v.2 no.4
• /
• pp.23-71
• /
• 1969

Sediment samples were taken at about half-mile intervals from all the inajor rivers draining the St. Austell granite mass. The minus 80 mesh(B.S.S.) fraction of each sample was analysed, using semiquantitative methods, for sodium, potassium, lithium, phosphorus, nickel, chromium, tin, tungsten, arsenic copper, zinc and lead. The work was carried out with the view to gaining further information as to the geographical distribution of such different granite facies as might axist, and to investigate the geochemical dispersion of these elements with relation to mineralisation in this area. The sesults confirm Exley's suggestion that the mass consists of two major granite intrusions, the earlier undifferentiated one is joined on the west by a later differentiated intrutive. During the work grid deviation maps proved particularly useful in obtaining data concerning the nature of the granite but frequency diagrams were not particularly helpful. All the known lode areas were associated with stream sediments containing anomalously high concentrations of lode metals and it is concluded that these high concentrations are due premarily to lode material transferred to the streams in the form of tailings lost during milling operations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.411-416
• /
• 2020

An optical arrangement has been set inside a photo-spectrometer to measure the reflectance of IR optics materials in mid IR range. The optical arrangement consists of equally spaced 4 gold coated full reflecting mirrors with the incidence angle of 45°. Baseline beam intensity I_B has been measured while the beam proceeds through the 4 mirrors. Reflectance of a mirror has been estimated from the I_B. And the beam intensity I_S with the specimen in the optical path has been measured with the 4th mirror replaced with the specimen. Reflectance of the specimen has been estimated from the value of I_S/I_B. Then the estimated reflectance has been put in Fresnel equation relating reflectance and refractive index(RI) to estimate the RI of the material. Measurement has been made for sapphire, germanium, magnesium fluoride, and zinc sulfide. The estimated RI of the materials are closely matching with reference data and the maximum difference less than 2% over the wavelength range 3-5㎛ for all materials tested. As an FT-IR photo-spectrometer with a broadband wavelength infrared light source is used, this method has the advantage of measuring the refractive index at multiple wavelengths in a single measurement.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.214.1-214.1
• /
• 2015

Thin-film transistors (TFTs)의 채널층으로 널리 쓰이는 indium-gallium-zinc oxide (IGZO)는 높은 전자 이동도(약 10 cm2/Vs)를 나타내며 유기 발광 다이오드디스플레이(OLED)와 대면적 액정 디스플레이(LCD)에 필수적으로 사용되고 있다. 하지만, 이러한 재료는 우수한 TFT의 채널층의 특성을 가지는 반면, ZnO 기반 재료이기 때문에 소자 구동에서의 안정성은 가장 큰 문제로 남아있다. 따라서 최근, IGZO layer의 특성을 향상시키기 위한 연구가 다양한 방법으로 시도되고 있다. IGZO의 조성비를 조절하여 전기적 특성을 최적화거나 IGZO layer의 조성 중 Ga을 다른 금속 메탈로 대체하는 연구도 이루어지고 있다. 그러나 IGZO에 미량의 도펀트를 첨가하여 박막 특성 변화를 관찰한 연구는 거의 진행되지 않고 있다. 산화물 TFTs의 전기적 특성과 안정성은 산소 함량에 영향을 많이 받는 것으로 알려져 있으며, 더욱이 TFT 채널층으로 쓰이는 IGZO 박막의 고유한 산소 공공은 디바이스 작동 중 열적으로 활성화 되어 이온화 상태가 될 때 소자의 안정성을 저하시키는 것이 문제점으로 지적되고 있다. 그러므로 본 연구에서는 낮은 전기 음성도(1.22)와 표준전극전위(-2.372 V)를 가지며 산소와의 높은 본드 엔탈피 값(719.6 kJ/mol)을 가짐으로써 산소 공공생성을 억제할 것으로 기대되는 yttrium을 IGZO의 도펀트로 도입하였다. 따라서 본 연구에서는 Y-IGZO의 박막 특성 변화를 관찰하고자 한다. 본 연구에서는 magnetron co-sputtering법으로 IGZO 타깃(DC)과 Y2O3 타깃(RF)를 이용하여 기판 가열 없이 동시 방전을 이용해 non-alkali glass 기판 위에 증착 하였다. IGZO 타깃은 DC power 110 W으로 고정하였으며 Y2O3 타깃에는 RF Power를 50 W에서 110 W까지 증가시키면서 Y 도핑량을 조절하였다. Working pressure는 고 순도 Ar을 20 sccm 주입하여 0.7 Pa로 고정하였다. 모든 실험은 $50{\times}50mm$ 기판 위에 총 두께 $50nm{\pm}2$ 박막을 증착 하였으며, 그 함량에 따른 전기적 특성 및 광학적 특성을 살펴보았다. 또한, IGZO 박막 제조 시 박막의 안정화를 위해 열처리과정은 필수적이다. 하지만 본 연구에서는 열처리를 진행하지 않고 Y-IGZO의 안정성 개선 여부를 보기 위하여 20일 동안 상온에서 방치하여 그 전기적 특성변화를 관찰하였다. 나아가 Y-IGZO 채널 층을 갖는 TFT 소자를 제조하여 소자 구동 특성을 관찰 하였다. Y2O3 타깃에 가해지는 RF Power가 70 W 일 때 Y-IGZO박막은 IGZO박막과 비교하여 상대적으로 캐리어 밀도는 낮은 반면 이동도는 높은 최적 특성을 얻을 수 있었다. 상온방치 결과 Y-IGZO박막은 IGZO박막에 비해 전기적 특성 변화 폭이 적었으며 이것은 Y 도펀트에 의한 안정성 개선의 결과로 예상된다. 투과도는 Y 도핑에 의하여 약 1.6 % 정도 상승하였으며 밴드 갭 내에서 결함 준위로 작용하는 산소공공의 억제로 인한 결과로 판단된다.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.1
• /
• pp.41-53
• /
• 2006

In this study, estimation of nonlinear adsorption isotherms(Langmuir & Freundlich adsorption isotherm) and advection-dispersion model parameters was conducted using genetic algorithm(GA) for Zn and Cd adsorption. Estimated parameters of nonlinear adsorption isotherms, which were obtained from the optimization process using genetic algorithm(GA), are nearly same with the parameters obtained from a linearization process of the nonlinear isotherms. Estimated effective diffusion coefficients, which were obtained from a finite element analysis of the advection-dispersion model and an optimization procedure using the genetic algorithm, for the metals were approximately in the order of $10^{-7}cm^2/s$ which could be obtained based on the linear distribution coefficient. The effective diffusion coefficients based on the nonlinear retardation factors were in the range of $10^{-6}{\sim}10^{-5}cm^2/s$. As a result, the correlation coefficient obtained between the measured and calculated concentration was over 0.9 which means that the genetic algorithm should be successfully applied to estimate the unknown parameters of the nonlinear adsorption isotherms and advection-dispersion model.

• Journal of the Korean earth science society
• /
• v.24 no.7
• /
• pp.635-649
• /
• 2003

Heavy metal concentrations and benthic foraminiferal distributions were investigated in three short sediment cores in order to understand the pollution history in Masan Bay. Sedimentation rates were 0.33 cm/yr, 0.20 cm/yr and 0.33 cm/yr in the inner bay, the out fall of Dugdong sewage disposal plant, and bay mouth, respectively. The rapid increases of copper, zinc and lead concentrations at the core depth of 10 cm the upper part indicated that Masan Bay has been polluted with industrial wastes since the 1940s. Benthic foraminifera in core sediments show that the variations in their distribution were followed by industrial pollution in the bay. The number of individuals and species diversity decreased, whereas agglutinated tests increased upward in the cores with increased heavy metal pollution. These shifts effectd the abundance of few tolerant forms and consequently decreased the species diversity. The opportunistic species Eggerella advena and Trochammina pacifica increased in polluted sediments. These species can be used as an indicator for assessments of environmental quality in Masan Bay.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3748-3754
• /
• 2009

An integral head loss test in a test apparatus was conducted to simulate chemical effects on a head loss across a strainer in a pressurized water reactor (PWR) containment water pool after a loss of coolant accident (LOCA). The test was conducted during 30 days in the condition of a short spray, a long spray, and no materials with chemical effects. The result exhibited that the head loss was affected on amounts of the exposed materials according to spray conditions. XRD analysis of the collected precipitates showed that the precipitates were phosphate compounds. Comparison of the head loss with dissolved species concentration showed that high increase rate of the head loss resulted from the corrosion of aluminum and zinc but slow increase rate of the head loss resulted from the precipitates induced by Si, Mg, and Ca from leaching reaction at NUKON and concrete after passivation of metal specimens.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.3
• /
• pp.93-108
• /
• 2013

This study is aimed to prepare the effective detail survey methods(Phase II) of abandoned metal mines through the contamination assessment for mine types and facilities in the abandoned metal mine areas. The study sites of 12 abandoned mines are located in Gyeonggi-do and Gangwon-do and those were chosen among 310 sites that the Phase II survey was conducted from 2007 to 2009 after considering the results of Phase I for abandoned mines scattered all over the country. 12 study sites were classified into four types; Type I sites only have pit mouth. Type II sites have pit mouth and mine-waste field. Type III sites have pit mouth and tailing sorting field. Type IV sites have pit mouth, tailing sorting field and concentrator(s). In forest land, paddy soil and farm land of Type I, As and Cd were showed average concentration, and Cu and Pb were high on the pit mouth area in one mines where the pit mouth was developed within 500 m. In the mines of Type II, Cu and Pb were showed average concentration too, but As and Cd were slightly high in pit mouth and mine-waste field. The mines of Type III which had grinding particle process through physical separation milling or hitting showed similar tendency with Type II. However, mines of Type IV pit mouth, mine-waste field and showed various results depending on defining the contamination sources. For example, if contamination source was pit mouth, the mixed results of Type I, II, II were showed. In tailing sorting field which was regarded as the most important source and having high mobility, however, if there were no facilities or it was difficult to access directly, field sampling was missed occasionally during phase I and phase II survey. For that reason, the assessment for tailing sorting field is missed and it leads to completely different results. In the areas of Type I mines, the concentration of heavy metals exceeded precautionary standards of soil contamination or not within 1,000 meters of pit mouth. Nickel(Ni) was the largest factor of the heavy metal contamination in this type. The heavy metals except Arsenic(As) were shown high levels of concentration in Type II areas, where pit mouth and mine-waste field were operated for making powder in upriver region; therefore, to the areas in the vicinity of midstream and downstream, the high content of heavy metals were shown. The tendency of high level of heavy metals and toxic materials contained in flotation agent used during sorting process were found in soil around sorting and tailing field. In the abandoned-pit-mouth area, drygrinding area and tailing sorting field area, the content of Cupper(Cu) and Zinc(Zn) were higher than other areas. Also, the contaminated area were larger than mine reclamation area(2,000 m) and the location of tailing sorting field was one of the important factors to estimate contaminated area.