• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.169-174
• /
• 2005

The conventional harmonic filters to reduce zero harmonic current from neutral reactors and Zig-Zag connection, have several disadvantages of the decreased reduction rate of harmonics under a light load, because they have the load factor-dependent reduction rate of harmonics, and the risk of potential breaking in the neutral line by heated neutral reactor. Based Zig-Zag connection and Open-Delta mode, this new harmonic eliminating device (HANOS) adopts the combination of Zig-Zag connection and Open-Delta mode-the latter is additionally applied to the transformer's core block for connection to the neutral line. The results of this study demonstrated that the new device could eliminate safely zero harmonic current running in the neutral line without heating.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.1
• /
• pp.54-60
• /
• 1998

Generally, spiral test has been used for evaluating course-keeping quality of a ship. But, there are many difficult problems in performing spiral test and reversed spiral test. Therefore, we propose zig-zag test instead of spiral test for evaluating curse-keeping quality of a ship. In this paper, K-T maneuvering response model is applied to the spiral curves which are systematically produced to calculate Zig-zag maneuver. Then, 1st overshoot angle and 2nd overshoot angle are plotted. And the relations between overshoot angles and band widths of spiral curve are discussed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.5-8
• /
• 2001

A three node flat triangular element incorporating Layerwise Zig-Zag Theory(HZZT) is developed suitable for analyzing damped laminated composite structures. Using an interdependent kinematic relation, the higher order shear rotations are replaced by in-plane displacements, a transverse displacement and section rotations, which result in three translations and two rotations. Natural frequencies and modal loss factors of cantilevered laminated plates with embedded damping layers are calculated with the zig-zag triangular element and compared to the experimental results and MSC/NASTRAN results using a layered combination of plate and solid elements.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.1-4
• /
• 2001

Dynamic analysis of laminated beams with a embedded damping layer under tension or compression axial load is investigated. Improved Layer-Wise Zig-Zag Beam Theory and Interdependent Kinematic Relation using the governing equations of motion are incorporated to model the laminated beams with a damping layer and a corresponding beam zig-zag finite element is developed. Flexural frequencies and modal loss actors under tension or compression axial load are calculated based on Complex Eigenvalue Method. The effect of the axial tension and compression load on the frequencies and loss factors is discussed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.114-117
• /
• 2001

A higher order zig-zag plate theory is developed to refine accurately predict fully coupled of the mechanical, thermal, and electric behaviors. Both the displacement and temperature fields through the thickness are constructed by superimposing linear zig-zag field to the smooth globally cubic varying field. Smooth parabolic distribution through the thickness is assumed in the transverse deflection in order to consider transverse normal deformation. Linear zig-zag form is adopted in the electric field. The layer-dependent degrees of freedom of displacement and temperature fields are expressed in terms of reference primary degrees of freedom by applying interface continuity conditions as well as bounding surface conditions of transverse shear stresses and transverse heat flux The numerical examples of coupled and uncoupled analysis are demonstrated the accuracy and efficiency of the present theory. The present theory is suitable for the predictions of fully coupled behaviors of thick smart composite plate under mechanical, thermal, and electric loadings.

• International Journal of Highway Engineering
• /
• v.14 no.6
• /
• pp.149-158
• /
• 2012

PURPOSES : This research is to evaluate the effects of zig-zag marking. METHODS : Based on the literature review, This research adopt Comparison Group method which was developed by Hauer. RESULTS : The findings are as follows. Effectiveness of treatment at all site 1.06, intersection 0.92, median bus lane 1.93, school zone 0.50, below 6-lane 0.48, above 6-lane 1.19, cat vs person 0.57, car vs car 1.36, car only 1.29. CONCLUSIONS : Though the analysis, it was founded that zig-zag marking on the small scale road(below 6-lane) and school zone contribute to reduce traffic accidents(effectiveness of the treatment : 0.50, 0.48). But the accidents at large scale road and median bus lane where installed zig-zag marking demonstrated negative result.(effectiveness of the treatment indicates exceed 1.0).

• Journal of computational fluids engineering
• /
• v.14 no.3
• /
• pp.63-68
• /
• 2009

The motion of a rising liquid droplet is different that of a bubble motion. Treatment of liquid drops is more complex because internal motion must be considered. A 3D unstructured CFD code has been developed to solve incompressible N-S equation for the droplet simulation. This front-tracking consideration which the interface is tracked explicitly is very available to apply for not only exact interface topology but also the high schmidt number issue, such as $CO_2$ dissolution. This paper is forced on the zig-zag motion of the liquid droplet. The simulation shows that if the rising droplet is located at the corner of the zig-zag path, the velocity is low and shape of the droplet is more spherical shape, results in the less drag coefficient. Twin horse shoe vortexes behind the rising droplet are presented and the topology of the droplet is compared with an experimental result during one period of the path.

• Journal of the Korean Society of Industry Convergence
• /
• v.16 no.3
• /
• pp.85-93
• /
• 2013

The MCT has been most extensively used in the machining. In particular, the ball endmill has been mainly adopted for finishing on the free- form surface. The advancement of CAD/CAM software has made it possible to develop various cutting pattern methods and to create diverse tool routes. Therefore, the current research made an attempt to find the optimal cutting pattern among the seven cutting patterns (i.e., Follow Periphery, Zig, Zig Zag, Concentric Zig, Concentric Zig Zag, Radial Zig, Radial Zig Zag) when aluminium 6000 series were machined by the ball endmill. The optimal pattern was found by comparing different shapes and surface roughness produced by the seven patterns. The current research found that each cutting pattern produced its own unique geometric features on the machined surface. It was found that the Radial Zig cutting pattern produced the lowest roughness on the flat surfaces. The Radial Zig Zag cutting pattern was found to produce the most accurate free-form surface. Finally, the most efficient cutting pattern in terms of machining time turned out to be the Follow Periphery.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.121-128
• /
• 2007

In this thesis, we would show how to lay out and produce the shell-type transformer using the world's first Zig-Zag winding way, instead of a general winding. Also, we omit the progress of varnish-impregnation, so that we could develop the new shell-type transformer winding which improves the short-circuit characteristics and dielectric strength. It has a copernican effect to reduce the thickness and the number of insulation papers, as compared with a general winding transformer. We would prove that it is far superior in cost reduction, loss reduction, and mechanical force of short-circuit. And eventually you must find it useful in the pole transformer for power distribution in the domestic power companies.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.135-141
• /
• 2013

PURPOSES : The lack of details of design guideline for zig-zag shaped section approaching central bus stop leads an traffic accident proneness. So, this study analysed the geometric elements of central bus stop area in terms of vehicle dynamics and suggested design alternatives. METHODS : The study analysed a dynamic behaviour of bus moving in and out of zig-zag shaped section using Auto-Turn under scenarios. Based upon dynamic analysis, the study found out the width of overtaking lane is the most influential factor for a safe moving at zig-zag alignment. RESULTS : The width of overtaking lane at design speed of 40, 50, and 60 km/h respectively was suggested given taper ratio of 1 to 10 required for Bus Rapid Transit (BRT), and the lane width is not wider than 4.0m which possibly makes two vehicles using the same lane. Also, the width of overtaking lane which mitigates the taper ratio was suggested with the same restriction about the maximum lane width. CONCLUSIONS : The results of the study can be used to prepare a design guideline on zig-zag shaped alignment of central bus exclusive lanes. The more stable moving is expected by applying the design alternatives suggested, therefore the lower rate of traffic crashes at the vicinity of central bus stops.