• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1582-1591
• /
• 2014

This paper presents a hybrid sensorless control for an interior permanent magnet synchronous motor (IPMSM) for zero-, low-, and high-speed regions. Many sensorless control methods such as an observer-based estimator have been introduced. However, most of the observer-based estimators have a disadvantage at start-up and in the low-speed region. To solve this problem, a simple strategy of using a hybrid system is proposed by integrating a high-frequency (HF) signal injection method and a full-order flux observer. In addition, an HF signal injection method with only a low pass filter (LPF) is proposed to simplify the hybrid system. The hybrid system achieves high-performance drive throughout the entire speed range. The effectiveness of the proposed hybrid technique is verified by experiments using an 11-kW IPMSM drive system.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.257-259
• /
• 2003

Landuse maps are prepared from satellite imagery and field observations were conducted at various locations in the study area. Compared to the field data and NDVI and RVI thematic maps, NDVI is better than RVI, because it compensates for changing illumination conditions, surface slope, aspect and other factors. Clouds, water and snow have negative values for RVI and NDVI. Rock and bare soils have similar reflectance in both NIR and visible band, so RVI and NDVI are near zero. In forest areas with good vegetation cover, NDVI is high and landslide occurrence is less. But if annual and biennial vegetations are present and if cultivation practices are changed frequently, NDVI is medium and landslide occurrence is moderate. In areas where deforestation and settlement is in progress, NDVI is less and landslide occurrence is more. The NDVI FCC thematic map may be used as an important layer in GIS application for landslide studies. Analyzing other layers such as slope, rainfall, soil, geology, drainage, lineament, etc with NDVI FCC layer will give a better idea about the identity of landslide prone areas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.222-225
• /
• 2000

BSCCO thin films have been fabricated by co-deposition at an ultralow growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $Po_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$ (onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a smd amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in d of the obtained films.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1294-1296
• /
• 2005

Because of its cost effectiveness, the Brushless DC Motor(BLDCM) is focused by the industry these days. Considering the constant back-EMF region of the BLDCM, only a simple position information should be provided for constant torque control. From this point of view, using expensive position sensors, such as encoder, resolver, etc, decreases the cost effectiveness of the BLDCM. The Proposed detecting circuit detects position of zero crossing point(ZCP) then relative position could be calculated from ZCP. This circuit is robust to noise because of working in the current level. BLDCM is driven from the position information by the ZCP The reliability on BLDCM sensorless control using the voltage detecting circuit is shown through simulation using Matlab.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.321-327
• /
• 1991

Experiments of quenching were made with cylindrical specimens of carbon steel S45C of diameters from 12 to 30mm were performed. The specimens were heated by electric furnace and quenched by immersion method. In order to analyze the temperature profile(cooling curves) of carbon steel including the latent heat of phase transformation, nonlinear heat conduction problem was calculated by the numerical method of inverse heat conduction problem using the apparent heat capacity method. The difference between the calculated and the experimented cooling curves was caused by the latent heat of phase transformation, and the effects of the latent heat were especially manifest at the cooling curves of center of specimens. The temperature and the quantity of the latent heat of phase transformation depend on the cooling speed at A sub(1) transformation point, and the region for cooling speed to become zero was caused by the latent heat of phase transformation.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.2
• /
• pp.149-155
• /
• 2001

The use of primitive cell volume and zero order Laue (ZOLZ) pattern is proposed to identify phase in a complex microstructure. Single convergent beam electron pattern containing higher order Laue zone ring from a nanosized region is sufficient to calculate the primitive cell volume of the phase, while ZOLZ pattern is used to determine the zone axis of the crystal. A computer program is used to screen out possible phases from the value of measured cell volume from convergent beam electron diffraction (CBED) pattern. Indexing of ZOLZ pattern follows in the program to find the zone axis of the identification from a single CBED pattern. An example of the analysis is given from the rapidly solidified $Al-Al_3Ti$ system.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.601-607
• /
• 1998

This paper presents the efficient 2-D linear brake analysis model which can compensate the lateral leakage flux by changingng the airgap length and magneto-motive force(MMF). The linkage flux of the 2-D analysis is larger than that of 3-D analysis. This is caused by the assumption in 2-D analysis that geometric and physical values are constant along the perpendicular direction(z) to the analysis region. The equivalent MMF have been calculated from the linkage flux difference between the 2-D and 3-D analyses which are performed at zero velocity. The performances of the linear brake have been analyzed effectively by using the compensated 2-D models without using 3-D FEM.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.16 no.1
• /
• pp.103-108
• /
• 1987

The heat transfer processes taking place in the side wall of a thermocline enclosure have been analyzed for idealized conditions based on the assumption that, at any instant time, side wall heat transfer processses are independent of the thermocline bulk motion. However, the axial tempera-ture distribution in the thermocline core provides the means for specifying the liquid medium-side boundary condition to the enclosure side wall. A picture is drawn which reflects the side wan response to thermocline bulk motion within the frame work of a quasi-steady analytic approach. For valves of the parameters typical of systems of engineering interest, the analysis shows that a significant amount of heat transfer short - circuiting can take place along the side wall enclosure. This phenomenon is favored by high values of $H_l$ and low values of P and $H_g$ respec-tively. The location of the point of zero normal heat flux on the side wan can be expected to mark, approximately, the region of confluence of two sidewall boundary flows respectively driven by the buoyant effects.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2022.11a
• /
• pp.99-102
• /
• 2022

실재하는 물체나 장소를 디지털 카메라나 휴대폰 카메라로 여러 장 촬영하여 얻은 2차원 이미지 데이터셋으로부터 3차원 영상을 얻기 위해서 이미지를 이루는 각 pixel의 depth 정보를 얻는 것은 필수적인 과정이다. 주어진 이미지에서 depth 정보를 얻기 위해 Shuhan Shen은 PatchMatch 알고리즘을 활용하는 것을 제안하였다. 그 이후 PatchMatch 기반의 알고리즘은 널리 사용되며 우수한 성능을 보이고 있다. PatchMatch 기반의 알고리즘을 사용해 depth를 추정하는 과정에서 depth와 법선 벡터를 Zero-mean Normalized Cross Correlation(ZNCC)를 사용해 평가한다. 하지만, ZNCC는 depth를 평가하려는 pixel의 주변 pixel들의 밝기 값 혹은 색상 값의 분포를 사용하기 때문에 밝기 값이나 색상 값의 변화가 적은 texture-less region에서는 신뢰성이 떨어진다. 본 논문에서는 이 문제를 epipolar geometry를 활용한 기하학적 정보를 이용하여 개선하고자 한다.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.3
• /
• pp.547-553
• /
• 2024

Hydrogen is considered a key energy source to achieve carbon neutrality through the global goal of 'Net Zero'. Due to limitations in domestic green hydrogen production, Korean companies are interested in importing green hydrogen produced overseas. Because Australia and the Middle East possess high-quality renewable energy resources, they are attracting attention as suitable regions for producing green hydrogen using renewable energy. The cost of constructing and operating a green ammonia plant varies depending on the region. In this study, an economic feasibility comparison of green ammonia plant construction in Australia and the Middle East is conducted. Through this, it is expected to contribute to the economic analysis and feasibility analysis of the project to import hydrogen in the form of green ammonia into Korea.