• 조명전기설비학회논문지
• /
• 제28권5호
• /
• pp.39-51
• /
• 2014

This paper deals with design of a direct-coupled, small-scaled permanent magnet generator (PMG) for wind power application. First, this paper determines rated power and speed of the PMG from measured characteristics of wind turbines. Second, we derive analytical solutions for the open-circuit field in order to determine optimum magnet thickness and pole pitch/arc ratio. Third, on the basis of open circuit field solutions, stator magnetic circuit including slot opening, teeth width and yoke thickness is designed. And then, a diameter of stator coil which agree with a required current density is calculated, and its turns are determined from the area of slot considering winding packing factor. Finally, finite element (FE) method is employed in analyzing the details of the designed PMG and, test results such as back-emf measurements are given to confirm the design.

• 조명전기설비학회논문지
• /
• 제28권2호
• /
• pp.48-53
• /
• 2014

The shield effect of 4 layered shield case was investigated in this paper. The material of the case was non-oriented SiFe sheet with a thickness of 0.5mm. The size of the case was 100mm wide, 100mm high and 300mm long. Relative permeability of SiFe sheet was needed to calculate shield effect. It was obtained from the measurement by a ferrite yoke and from the calculation by eddy current FEM analysis. Three configurations were used to connect both ends of SiFe sheet. First one is a connection by double-welded butt. Second one is to put the sheet the same material above the confronted both ends of the sheet to avoid a leakage magnetic flux. The last one is ideally without any connection. The shield effect of the second one agreed well with the last one and showed the shield effect of -40dB.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.1021-1025
• /
• 2002

There have been many researches performed on the formability of axisymmetric or rectangular cup shapes in the deep drawing processes. But non-axisymmetric deep drawing processes rely upon empirical knowledge of experts in most cases. Especially, there have been few researches for multi-stage elliptical deep drawing processes. In this study, formability and thickness distributions of elliptical yoke products were predicted by using finite element analysis. The results of the analysis were compared with those of experiments for validity.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1232-1240
• /
• 2002

Recently, linear motors are applied to many small precision products. Thus high generating power with small size is required of it. In order to increase the motor efficiency, the design variables need to be optimized. In this study, Vector Fields FEM software, OPERA-3d, was used for simulating linear motor. The thrust and magnetic flux density at the air-gap center were simulated and compared with the experimental results. Taguchi method was applied to investigate the effects of each variables. As a result, the thickness of conductor and magnet was important for the thrust but the thickness of the yoke. The temperature of the conductor was determined by finding the thermal conductivity that was determined by experimentation. Correlation equation relating to the thrust and temperature was proposed by Latin square and Least Square method. The optimum design variables were determined by correlation equation, and compared with simulation results. According to this analysis, thrust force of linear motor was improved about 7% comparing with conventional model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1043-1044
• /
• 2011

This paper discusses the electromagnetic and mechanical design considerations to improve the design accuracy and power to mass ratio of multi-stack axial flux permanent magnet synchronous generator (AFPMSG). Design accuracy of multi-stack AFPMSG for direct drive wind turbine application is improved by considering magnetic flux leakages and fringing effect. FEM structural analysis is utilized to increase power to mass ratio of three-stack AFPMSG by reducing the rotor yoke thickness considering magnetic and centrifugal forces and Von Mises stress distribution.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.819-821
• /
• 2001

This paper describes a characteristics of MFL according to the position of Hall sensor Magnetic Flux Leakage(MFL) Method is used to detect surface defect in ferromagnetic plate. A plate has a surface defect and magnetizing equipment are producted to perform Non-Destructive Testing(NDT) using MFL. The SM 45C carbon steel plate is adopted to this experiment. there is a artifical defect with a twice of thickness and a half of depth of plate. Magnetizing equipment is composed of yoke made by layer-built of silicon sheet steel, NdFeB magnetic and iron brushes. Detecting defect is performed by MFL NDT using Hall sensor. It is shown that magnetic flux detected by Hall sensor is affected according to the position of Hall sensor through MFL experiment and numerical analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.760-761
• /
• 2008

This paper deals with the core loss as well as torque characteristics according to the change of stator shape in an interior permanent magnet synchronous motor (IPMSM). The finite element method and functional core loss data obtained by the steinmetz equation are used in order to estimate the core loss. To minimize the core loss caused by the shape of tooth tip, slot-area and volume of permanent magnet, those are all the same in each model. In the end, the ratio between tooth width and yoke thickness to minimize the core loss in the IPMSM is presented in this paper.

• 한국방재안전학회논문집
• /
• 제11권2호
• /
• pp.53-60
• /
• 2018

본 연구에서는 강판에 발생한 국부적인 손상의 진단을 위해 강자성의 연속체 구조물에 적합한 비파괴진단 기법인 누설자속 기법을 적용하였다. 강판시편의 두께 변화에 따른 누설자속 기반 진단 기법의 민감도를 분석하기 위해 각각 다른 두께를 가지는 몇 가지의 강판시편을 준비하였고, 각각의 시편에 3가지 깊이의 인공결함을 가공하였다. 홀센서와 자화요크를 이용하여 일정한 자화밀도를 가지는 누설자속 센서헤드를 제작하여 강판시편으로부터 누설자속 신호를 계측하였다. 센서헤드로부터 수집된 자속신호의 품질향상을 위해 일련의 신호처리 과정을 거쳤으며, 각 손상지점으로부터 계측된 누설자속 신호의 확인을 통해 국부손상 감지의 가능성을 확인하였다. 강판두께에 따른 누설자속 기법의 손상감지 민감도의 분석을 위해 각각 다른 두께의 강판시편으로부터 검출된 MFL 신호에서 P-P value를 정량적으로 추출하였고 그 값을 비교 분석 하였다.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.728-734
• /
• 2000

An asymmetric actuator can be used to reduce the distance between the reflective mirror and objective lens of a small optical disk drive for use in the notebook-sized personal computer data storage devices. However, this asymmetric actuator is very sensitive to the subsidiary resonance which is caused by its rigid body motion. In this paper, an analytical approach using a simple lumped parameter system model is presented with a physical insight to investigate why the subsidiary resonance occurs. The finite element method is used to figure out the force and torque characteristics of the asymmetric actuator which are essential to understand the subsidiary vibration characteristics. The frequency responses are presented to examine how the subsidiary resonance is altered for various situations of having different thickness of a yoke and permanent magnet and of having a different magnet circuit. Finally, the design guidelines to avoid the subsidiary resonance will be presented.

• 반도체디스플레이기술학회지
• /
• 제11권2호
• /
• pp.1-6
• /
• 2012

In this study, a high performance rotary magnet type magnetron source for roll-to-roll sputter system has been developed. We analyzed the density of magnetic field as a function of size variation of the magnet which are in the center and edge of the target. The target efficiency showed the best result when the width of center magnet, the width of edge magnet, the angle of edge magnet, and the rotation angle of Yoke are 20mm, 10mm, $56^{\circ}$, and $16^{\circ}$, respectively. On the basis of the results of magnet array, Roll-to Roll magnetron source was fabricated and tested. The uniformity of the film thickness and that of the sheet resistance was ${\pm}1.62%$ and ${\pm}4.13%$, and the resistivity was $2.79{\times}10^{-3}W{\cdot}cm$.