• Carbon letters
• /
• v.26
• /
• pp.107-111
• /
• 2018

• 연구논문집
• /
• s.29
• /
• pp.111-121
• /
• 1999

Weft insertion and Beating mechanism which weaves fabric with completion the pattern of warp yarn and weft yarn in the high speed rapier loom is driven by cam operating method. This mechanism has 4 cams on the coaxial line for driving. These cams form a pair by two. and perform a conjugate motion with each other. By this reason, it is necessary for two pairs to realize the synchronized motion through exact and optimal design. From this viewpoint, to analysis the whole cams' movement and to realize the high speed of rapier loom, I tried to develop the computer aided simulation program. In this study, I would like to introduce the simulation program about above-mentioned 4 kinds of cam mechanism which can display the profiles of 2 pairs of cam mechanism not to speak of mutual relationships of their movement on the monitor.

• Textile Coloration and Finishing
• /
• v.13 no.2
• /
• pp.49-49
• /
• 2001

Interlace texturing is very useful method to make compound yarns for new synthetic fabrics. In this study, we make the compound yarns for peach skin fabric by interlace texturing method. This study surveys relationship between physical properties of interlace textured yarns and process conditions such as air pressure, yarn tension and take-up speed. Nip density, tensile properties and multi-step shrinkage of the various specimens were discussed with process conditions.

• Textile Coloration and Finishing
• /
• v.9 no.4
• /
• pp.7-19
• /
• 1997

The purpose of the study was to investigate the shrinkage and creep behavior of PET filaments which were prepared at various spinning speeds(3,300, 4,000, 5,000, 6,000, and 7,000m/min) and anneal($120^{\circ}$, 30min & $150^{\circ}$, 40min). In order to determine the shrinkage and creep behavior with the crystallinity change, PET filaments were treated with low(12$0^{\circ}C$, 30min) and high($150^{\circ}$, 40min) temperature conditions with hot air dryer under the constant tension. The results of the study were as follows: as the spinning speed increased, the degree of shrinkage and elongation of the sample treated by wet condition decreased. The sample with 0.01g/d of load under various spinning speeds showed shrinkage behavior and highest shrinkage ratio at $76^{\circ}$ which was Tg of PET. The degree of shrinkage and elongation of the treated sample was less than those of the untreated sample by wet treatment. Especially, there was less degree of shrinkage and elongation of the sample treated by higher temperature condition. In 3,300m/min of spinning speed the draw ratio of undrawn yarn of a mixture of a-axis orientation and c-axis orientation was 2.0, which is similar to the value of the traditional drawn yarn. Finally, there was a big range of shrinkage and elongation by wet treatment in 3,300 m/min of spinning speed.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.1
• /
• pp.27-33
• /
• 1999

Effects of spinning speed and draw ratio on structure and mechanical properties of PP filament. A The crystalline structure and mechanical properties of uniaxially deformed polypropylene filament has been examined by XRD, birefringence, UTM and density method. Uniaxially deformed PP filament was prepared of various spinning speeds (300, 600, 900m/min.) and draw ratio(x2, x3, x4). From the results of these studies, it found the following facts. Firstly, it was found that the crystallinity and crystallite size (110plane) of the samples were increased with increasing of spinning speed and draw ratio, especially, it was rapidly increased between as spun yarn and 2 times draw ratio. Secondly, birefringence value was increased with increasing of spinning speed and draw ratio. The mechanical properties of initial modulus, tensile strength were increased with increasing of spinning speed and draw ratio also, but the degree of elongation decreased as spinning speed and draw ratio.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.1
• /
• pp.114-120
• /
• 2017

In recent years, applications of high speed rotating bodies have diversified. It is necessary for a device rotating at high speed to be balanced to minimize vibration. It is necessary to reduce the unbalancing factor to evenly wind the yarn. In this study, we also attempted to devise a technique to minimize the unbalance that occurs while assembling the components of spindles and to simplify the balancing procedure in the field. To balance the spindle, the vibration of the rotating spindle was measured using a laser displacement meter. We also performed balancing using the influence coefficient method by considering the phase.

• Textile Coloration and Finishing
• /
• v.16 no.6
• /
• pp.35-43
• /
• 2004

This study surveys the physical properties of ATY produced with FDY and POY. ATY is made with 70d Nylon FDY and 80d Nylon POY using AIKI air jet texturing machines, respectively. The processing parameters such as air pressure and yam speed are varied, and air pressure is varied ranging with 8.5bar, l0.5bar and 1l.5bar, and yarn speed is varied ranging with 400m/mim, 450m/mim, and 500m/min. The various physical properties of ATY made by POY and FDY denier, wet shrinkage, dry shrinkage, tensile properties, thermal stress and instability are measured and discussed with air pressure and yam speed. The shrinkage simulation of ATY is performed for analysing the process shrinkage on the dyeing and finishing processes.

• Macromolecular Research
• /
• v.17 no.6
• /
• pp.378-387
• /
• 2009

This research compared three methods for producing and processing nanocomposite polypropylene filament yarns with permanent antimicrobial efficiency. The three methods used to mix antimicrobial agents based on silver nano particles with PP were as follows: 1) mixing of PP powder and inorganic nanocomposite filler with the appropriate concentration using a twin-screw extruder and preparing granules, 2) method 1 with a singlerather than twin-screw extruder, and 3) producing the masterbatch by a twin-screw extruder and blending it with PP in the melt spinning process. All pure polypropylene samples and other combined samples had an acceptable spinnability at the spinning temperature of $240^{\circ}C$ and take-up speed of 2,000 m/min. After producing as-spun filament yarns by a pilot plant, melt spinning machine, the samples were drawn, textured and finally weft knitted. The physical and structural properties (e.g., linear density, tenacity, breaking elongation, initial modulus, rupture work, shrinkage and crystallinity) of the as-spun and drawn yarns with constant and variable draw ratios (the variable draw ratio was used to gain a constant breaking elongation of 50%) were investigated and compared, while DSC, SEM and FTIR techniques were used to characterize the samples. Finally, the antibacterial efficiency of the knitted samples was evaluated. The experimental results revealed that the crystallinity reduction of the as-spun yarn obtained from method 1 (5%) was more than that of method 2 (3%), while the crystallinity of the modified as-spun yarns obtained with method 3 remained unchanged compared to pure yarn. However, the drawing procedure compensated for this difference. By applying methods 2 and 3, the drawing generally improved the tenacity and modulus of the modified fibers, whereas method 1 degraded the constant draw ratio. Although the biostatic efficiency of the nanocomposite yarns was excellent with all three methods, the modified fabrics obtained from methods 1 and 2 showed a higher bioactivity.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.10
• /
• pp.5023-5038
• /
• 2017

Big data is an emerging technology which deals with wide range of data sets with sizes beyond the ability to work with software tools which is commonly used for processing of data. When we consider a huge network, we have to process a large amount of network information generated, which consists of both normal and abnormal activity logs in large volume of multi-dimensional data. Intrusion Detection System (IDS) is required to monitor the network and to detect the malicious nodes and activities in the network. Massive amount of data makes it difficult to detect threats and attacks. Sequential Pattern mining may be used to identify the patterns of malicious activities which have been an emerging popular trend due to the consideration of quantities, profits and time orders of item. Here we propose a sequential pattern mining algorithm with fuzzy logic feature selection and fuzzy weighted support for huge volumes of network logs to be implemented in Apache Hadoop YARN, which solves the problem of speed and time constraints. Fuzzy logic feature selection selects important features from the feature set. Fuzzy weighted supports provide weights to the inputs and avoid multiple scans. In our simulation we use the attack log from NS-2 MANET environment and compare the proposed algorithm with the state-of-the-art sequential Pattern Mining algorithm, SPADE and Support Vector Machine with Hadoop environment.

• 연구논문집
• /
• s.22
• /
• pp.75-83
• /
• 1992

The beating motion of a high speed shuttleless loom is driven by cams. Two cams become one system and their shaft laid across each other. Moreover, the shape of the cams is very complex and requires high precision for successful weft insertion and good interlacing with warp yarn. The iterative contact method is developed for use in design and analysis of the driving mechanism of a disk type cam with oscillating roller follower. The optimum design is performed by utilizing a CAD program, DISKCAM. The 8th order polynomial is selected to interpolate the desired shape trajectory of the cam, the optimal shape of the cams is defined based on the demension of the follower. The kinematic motion of the beating cam mechanism is investigated. The phase angle is determined to achive harmonious cam motions