• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.33-39
• /
• 2015

Olmesartan affiliated to biopharmaceutics classification system class 2 is a poorly water soluble drug. For this reason, olmesartan showed a low bioavailability and a lot of difficulties in the process of designing the pharmaceutical formulation. We prepared the solid dispersions of olmesartan. We confirmed the dissolution rate of drug which was prepared by manufacturing. The pharmaceutical formulation of solid dispersions was designed by using PVP as water soluble polymer. We analyzed morphological feature of solid dispersion by employing a scanning electron microscope. Then, the crystalline property of solid dispersion was confirmed through X-ray diffraction and differential scanning calorimeter. Also, the chemical change of solid dispersion was confirmed by the Fourier transform infrared spectroscopy. In vitro dissolution test was used to analyze the dissolution rate of solid dispersion. The prepared solid dissolution olmesartan confirmed the dissolution rate in the pH 1.2. It was compared with olmetec and improved dissolution rate through solid dispersion.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.61-65
• /
• 2012

A $Li_2O-2SiO_2$ ($LS_2$) glass was investigated as a lithium-ion conducting oxide glass, which is applicable to a fast ionic conductor even at low temperature due to its high mechanical strength and chemical stability. The $Li_2O-2SiO_2$ glass is likely to be broken into small pieces when quenched; thus, it is difficult to fabricate a specifically sized sample. The production of properly sized glass samples is necessary for device applications. In this study, we applied spark plasma sintering (SPS) to fabricate $LS_2$ glass samples which have a particular size as well as high transparency. The sintered samples, $15mm\phi{\times}2mmT$ in size, ($LS_2$-s) were produced by SPS between $480^{\circ}C$ and $500^{\circ}C$ at 45MPa for 3~5mim, after which the thermal and dielectric properties of the $LS_2$-s samples were compared with those of quenched glass ($LS_2$-q) samples. Thermal behavior, crystalline structure, and electrical conductivity of both samples were analyzed by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and an impedance/gain-phase analyzer, respectively. The results showed that the $LS_2$-s had an amorphous structure, like the $LS_2$-q sample, and that both samples took on the lithium disilicate structure after the heat treatment at $800^{\circ}C$. We observed similar dielectric peaks in both of the samples between room temperature and $700^{\circ}C$. The DC activation energies of the $LS_2$-q and $LS_2$-s samples were $0.48{\pm}0.05eV$ and $0.66{\pm}0.04eV$, while the AC activation energies were $0.48{\pm}0.05eV$ and $0.68{\pm}0.04eV$, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.386-386
• /
• 2012

For white light emitting diode (LED) applications, it has been reported that Y3Al5O12:Ce3+ (YAG:Ce) in nano-sized phosphor performs better than it does in micro-sized particles. This is because nano-sized YAG:Ce can reduce internal light scattering when coated onto a blue LED surface. Recently, there have been many reports on the synthesis of nano-sized YAG particles using bottom-up method, such as co-precipitation method, sol-gel process, hydrothermal method, solvothermal method, and glycothermal method. However, there has been no report using top-down method. Top-down method has advantages than bottom-up method, such as large scale production and easy control of doping concentration and particle size. Therefore, in this study, nano-sized YAG:Ce phosphors were synthesized by a high energy beads milling process with varying beads size, milling time and milling steps. The beads milling process was performed by Laboratory Mill MINICER with ZrO2 beads. The phase identity and morphology of nano-sized YAG:Ce were characterized by X-ray powder diffraction (XRD) and field-emission scanning electron microscopy (FESEM), respectively. By controlling beads size, milling time and milling steps, we synthesized a size-tunable and uniform nano-sized YAG:Ce phosphors which average diameters were 100, 85 and 40 nm, respectively. After milling, there was no impurity and all of the peaks were in good agreement with YAG (JCPDS No. 33-0040). Luminescence and quantum efficiency (QE) of nano-sized YAG:Ce phosphors were measured by fluorescence spectrometer and QE measuring instrument, respectively. The synthesized YAG:Ce absorbed light efficiently in the visible region of 400-500 nm, and showed single broadband emission peaked at 550 nm with 50% of QE. As a result, by considering above results, high energy beads milling process could be a facile and reproducible synthesis method for nano-sized YAG:Ce phosphors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.251-251
• /
• 2016

For several decades, industrial processes consume a huge amount of raw water for various objects that consequently results in the generation of large amounts of wastewater. Wastewaters are consisting of complex mixture of different inorganic and organic compounds and some of them can be toxic, hazardous and hard to degrade. These effluents are mainly treated by conventional technologies such are aerobic and anaerobic treatment and chemical coagulation. But, these processes are not suitable for eliminating all hazardous chemical compounds form wastewater and generate a large amount of toxic sludge. Therefore, other processes have been studied and applied together with these techniques to enhance purification results. These include photocatalysis, absorption, advanced oxidation processes, and ozonation, but also have their own drawbacks. In recent years, electrochemical techniques have received attention as wastewater treatment process that could be show higher purification results. Among them, boron doped diamond (BDD) attract attention as electrochemical electrode due to good chemical and electrochemical stability, long lifetime and wide potential window that necessary properties for anode electrode. So, there are many researches about high quality BDD on Nb, Ta, W and Si substrates, but, their application in effluents treatment is not suitable due to high cost of metal and low conductivity of Si. To solve these problems, Ti has been candidate as substrate in consideration of cost and property. But there are adhesion issues that must be overcome to apply Ti as BDD substrate. Al, Cu, Ti and Nb thin films were deposited on Ti substrate to improve adhesion between substrate and BDD thin film. In this paper, BDD films were deposited by hot filament chemical vapor deposition (HF-CVD) method. Prior to deposition, cleaning processes were conducted in acetone, ethanol, and isopropyl alcohol (IPA) using sonification machine for 7 min, respectively. And metal layer with the thickness of 200 nm were deposited by DC magnetron sputtering (DCMS). To analyze microstructure X-ray diffraction (XRD, Bruker gads) and field emission scanning electron microscopy (FE-SEM, Hitachi) were used. It is confirmed that metal layer was effective to adhesion property and improved electrode property. Electrochemical measurements were carried out in a three electrode electrochemical cell containing a 0.5 % H2SO4 in deionized water. As a result, it is confirmed that metal inter layer heavily effect on BDD property by improving adhesion property due to suppressing formation of titanium carbide.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.267-274
• /
• 2006

Greenhouse gas reduction will be highlighted as the most pending question in the cement industry in future because the production of Portland cement not only consumes limestone, clay, coal, and electricity, but also release waste gases such as $CO_2,\;SO_3$, and NOX, which can contribute to the greenhouse effect and acid rain. To meet the increase of cement demand and simultaneously comply with the Kyoto Protocol, cement that gives less $CO_2$ discharge should be urgently developed. This study aims to manufacture non-sintering cement(NSC) by adding phosphogypsum(PG) and waste lime(WL) to granulated blast furnace slag(GBFS) as sulfate and alkali activators. This study also Investigates the hydration reaction of NSC through analysis of scanning electron microscopy(SEM), X-ray diffraction(XRD), differential thermal analysis(DTA), and pH. Results obtained from analysis of the hydrate have shown that the glassy films of GBFS are destroyed by the activation of alkali and sulfate, ions eluted from the inside of GBFS react with PG and produce ettringite, and consequently the remaining component in GBFS slowly produced C-5-H(I) gel. Here, PG is considered not only to play the role of simple activator, but also to work as a binder reacting with GBFS.

• Journal of Korea Soil Environment Society
• /
• v.5 no.2
• /
• pp.67-85
• /
• 2000

Fifty seven soil samples were collected from the paddy soil filled with tailings in the vicinity of the Seosung Pb-Zn mine. Those samples were analyzed for As, Cd, Co, Cr, Cu, Pb, and Zn in order to investigate heavy metal pollution levels in the paddy soil. Analyses of the soil samples were carried out using Inductively Coupled Plasma Atomic Emission Spectrometry(ICP-AES) . Paddy soils show pH range from 6.55 to 8.26. X-ray diffraction analyses of the paddy soil indicate that the soils consist predominantly ankerite, siderite, quartz, mica, and clay minerals with minor amounts of amphibole and chlorite. The mineral composition of the waste rocks consists of massive galena, sphalerite, and minor amounts of pyrite, arsenopyrite, chalcopyrite, calcite, siderite, Pb-sulfosalt, and marcasite. The paddy soils were significantly contaminated by heavy metals(average concentrations, As: 334.4 ppm, Cd: 37.6 ppm, Co: 15.7 ppm, Cu: 214.1 ppm, Pb: 4,612 ppm, and Zn: 4,468 ppm).

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.13-18
• /
• 2010

The present study was undertaken to investigate the characteristic of suspended matter in soils of Imha-Dam area by turbidity. Soil sampling was conducted at 5 points of Yeongyang (Turbid area) and 2 points of Cheongsong (Clean area). Experimental analysis was conducted using those samples. The pH of water in the soils at turbid area was higher than that of clean area. X-ray diffraction analysis showed that every sample consists in mainly quartz, illite and feldspar before precipitation. After precipitation for 3 days, the content of quartz and feldspar was decreased and the content of illite was increased at turbid area. The soil of Sinheung (St. 6) at clean area was analyzed only illite. SEM-EDS analysis showed the much content of $SiO_2$ as to every sample before precipitation, but $K_2O$, MgO, $Al_2O_3$, CaO and $Fe2O_3$ with illite was increased after precipitation for 3 days as to every sample. Experimental results exhibited that the major mineral of turbid water was illite at turbid area and clean area.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.250-254
• /
• 2011

We have synthesized bluish-green, highly-efficient $BaSi_2O_2N_2:Eu^{2+}$ and $(Ba,Sr)Si_2O_2N_2:Eu^{2+}$ phosphors through a conventional solid state reaction method using metal carbonate, $Si_3N_4$, and $Eu_2O_3$ as raw materials. The X-ray diffraction (XRD) pattern of these phosphors revealed that a $BaSi_2O_2N_2$ single phase was obtained. The excitation and emission spectra showed typical broadband excitation and emission resulting from the 5d to 4f transition of $Eu^{2+}$. These phosphors absorb blue light at around 450 nm and emit bluish-green luminescence, with a peak wavelength at around 495 nm. From the results of an experiment involving Eu concentration quenching, the relative PL intensity was reduced dramatically for Eu = 0.033. A small substitution of Sr in place of Ba increased the relative emission intensity of the phosphor. We prepared several white LEDs through a combination of $BaSi_2O_2N_2:Eu^{2+}$, YAG:$Ce^{3+}$, and silicone resin with a blue InGaN-based LED. In the case of only the YAG:$Ce^{3+}$-converted LED, the color rendering index was 73.4 and the efficiency was 127 lm/W. In contrast, in the YAG:$Ce^{3+}$ and $BaSi_2O_2N_2:Eu^{2+}$-converted LED, two distinct emission bands from InGaN (450 nm) and the two phosphors (475-750 nm) are observed, and combine to give a spectrum that appears white to the naked eye. The range of the color rendering index and the efficiency were 79.7-81.2 and 117-128 lm/W, respectively. The increased values of the color rendering index indicate that the two phosphor-converted LEDs have improved bluish-green emission compared to the YAG:Ce-converted LED. As such, the $BaSi_2O_2N_2:Eu^{2+}$ phosphor is applicable to white high-rendered LEDs for solid state lighting.

• KSBB Journal
• /
• v.24 no.6
• /
• pp.527-532
• /
• 2009

Lignocellulose represents a key sustainable source of biomass for transformation into biofuels and bio-based products. Unfortunately, lignocellulosic biomass is highly recalcitrant to biotransformation, both microbial and enzymatic, which limits its use and prevents. As a result, effective pretreatment strategies are necessary. The vast majority of pretreatment strategies have focused on achieving a reduction of lignin content. In this work, an ethanosolv pretreatment has been evaluated for extracting lignin from barley straw. 75% ethanol was used as a pretreatment solvent to extract lignin from barley straw. The influence on delignification of three independent variables are temperature, time, catalyst (1 M $H_2SO_4$) dose. The best pretreatment condition observed was $180^{\circ}C$, 120 min, 0.2% $H_2SO_4$ and delignification was 38%. A combined roasting and ethanosolv, 2-step pretreatment, was developed in order to improve the delignification. Roasting didn't increase the delignification but reduced the pretreatment time. X-ray diffraction results indicated that these physical changes enhance the enzymatic digestibility in the ethanosolv treated barley straw. The cellulose in the pretreated barley straw becomes more crystalline without undergoing ethanosolv.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.5
• /
• pp.478-482
• /
• 2001

This study was conducted to get a knowledge on food components of cuttle bone (CB) as a food resource. The yields and ash contents of CB were about $7.5\%$ on whole cuttle fish and about $90\%$ on dry basis, respectively, The contents of heavy metal might not invoke health risk in using food resource, The major mineral of CB was calcium as about $22\%$ in content. The yields, proximate compositions, heavy metal and mineral contents were not significantly different between domestic and imported CB. Judging from X-ray diffraction pattern, most of calcium in CB was present as a form of calcium carbonate (CC), and scanning electron micrograph showed irregular form. Buffering capacity of CB showed strongly at pH 7, and its pattern was the same as shown in that of CC, And CB solution showed a very high degree in turbidity comparing to that of CC solution. The solubility of CB was superior to that of CC, but inferior to those of calcium powders on the market, It was concluded from above results that CB could be effectively utilized as a calcium source.