• Korean Chemical Engineering Research
• /
• v.58 no.2
• /
• pp.313-318
• /
• 2020

Bi₂WO₆ were successfully synthesized using EGME, GL, EG and water as solvents by a conventional hydrothermal method. They were characterized by XRD, DRS, BET and SEM and we also investigated the photocatalytic activity of these materials for the decomposition of Rhodamin B under visible light irradiation. The XRD results revealed the successful synthesis well-crystallized Bi₂WO₆ crystals with Aurivillius structure when EGME and EG are used as solvents. In addition, the well-crystallized Bi₂WO₆ crystals showed the flower-like structure. The Bi₂WO₆ catalysts prepared at 180 ℃ using EGME as a solvent showed the highest photocatalytic activity. The Bi₂WO₆ catalysts prepared at mole ratio of H₂O/EGME more than 50% showed high photocatalytic activity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.11-16
• /
• 2006

This paper reports the correlation between dielectric constant and degree of amorphism of the hybrid type SiOC thin films. SiOC thin films were deposited by high density plasma chemical vapor deposition using bistrimethyl- silylmethane(BTMSM,$H_{9}C_{3}-Si-CH_{2}-Si-C_{3}H_{9}$) and oxygen precursors with various flow rate ratio. As-deposited film and annealed films at $400^{\circ}C$ were analyzed by XRD. The SiOC thin films were amorphous from XRD patterns. For quantitative analysis, the diffraction pattern of the samples was transformed to radial distribution function by Fourier analysis, and then compared with each other. The degree of amorphism of annealed films was higher than that of as-deposited ones. The dielectric constant varied in accordance with flow rate ratio of precursors. The lowest dielectric constant was obtained from the as-deposited film which has the highest degree of amorphism after annealing.

• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.193-199
• /
• 2006

The catalytic oxidation of toluene over $-Al_2O_3$ supported copper-manganese oxide catalysts in the temperature range of $160-280^{\circ}C$ was investigated by employing a fixed bed flow reactor. The catalysts were characterized by BET, scanning electron microscopy (SEM), temperature-programmed reduction(TPR), temperature-programmed oxidation(TPO), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction(XRD) techniques. Catalytic oxidation of toluene was achieved at the below $280^{\circ}C$, and the optimal content of copper and manganese in the catalyst was found to be 15.0 wt％Cu-10.0 wt％Mn. From the TPR/TPO and XPS results, the redox peak of 15 Cu-10 Mn catalyst shifted to the lower temperature, and the binding energy was shifted to the higher binding energy. Furthermore, It is considered that $Cu_{1.5}Mn_{1.5}O_4$ is superior to Mn oxides and CuO in the role as active factor of catalysts from the XRD results and also catalytic activities are dependent on the redox ability and high oxidation state of catalysts.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1096-1101
• /
• 2003

Si -substituted hydroxyapatite has been prepared to obtain biomaterials having an improved biocompatibility. From FT-IR, XRD, and ICP analyses, it was confirmed that the single-phase of hydroxyapatite substituted by Si has formed. Si- substituted hydroxyapatite of up to 2 wt% for Si keeps its original structures intact for the sintering temperatures of up to 1200$^{\circ}C$. However, it is observed that the ion substitutions by the amount higher than the above ratios for the hydroxyapatite leads to destabilize original structures of the hydroxyapatite and to produce tricalcium phosphate and calcium phosphate silicate phases when the samples were sintered at 1l00$^{\circ}C$ or higher.

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.4
• /
• pp.227-234
• /
• 2018

In this work, we have prepared the reactive media with the pyrophyllite based using ceramic extrusion process. The characteristics of pyrophyllite were analyzed using XRD, XRF, DSC-TGA and Zeta-potential analysis. The study of pyrophyllite based ceramic reactive media were conducted under various roasting temperature (500 to $1,300^{\circ}C$) conditions. With increasing the roasting temperature, strength was increased but BET surface area was decreased. Thermally treated pyrophyllite were analyzed by means of weight loss and structural changes as detected by using XRD, DSC-TGA and SEM analysis. Pyrophyllite primarily transforms to pyrophyllite dehydroxylate after roasting at $1,000^{\circ}C$. Pyrophyllite dehydroxylate transforms to mullite and cristobalite at $1,300^{\circ}C$. This study demonstrates that pyrophyllite could be used as a reactive media for ceramic support layers from Permeable Reactive Barriers.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.573-580
• /
• 2008

In this paper, we estimated the effect of the siliceous filler's particle size on the performance of Ultra High Performance Concrete (UHPC). Filler's particle diameters considered in this paper were about 2, 4, 8, 14, $26{\mu}m$ and the performance was evaluated by testing fluidity in fresh concrete, compressive strength, ultimate strain, elastic modulus and flexural strength in hardened concrete. We also carried out XRD and MIP tests to analyze the relationship between the mechanical properties and microstructure. Test results showed that the smaller filler's particle size improves flowability and strength properties. MIP results revealed that the smaller size of filler decreased the porosity and thus increased the strength of UHPC. From XRD analysis, we could find out there were little influence of filler's particle size on chemical reactivity in UHPC.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.25-35
• /
• 2018

This study presents microstructural characteristics and strength properties of alkali-activated kaolin(K)-fly ash(FA) blends binders. The compressive strength, X-ray diffraction(XRD), thermogravimetric(TG) analysis and SEM/EDS were measured for hardened samples. The results were shown that all the samples had developed the compressive strength over time, regardless of replacement levels of K. It was found that when the amount of K increased, the strengths of samples decreased. In XRD result, no new crystalline phases were observed in all the hardened samples other than the crystalline components of raw FA and K, whereas TG analysis showed that N-A-S-H gel was formed as a reaction product in all the samples. Samples did not have the typical microstructure of dense, and there is little significant difference between the microstructures of the samples despite the differences in the strength testing results with replacement ratios of K. This study showed that the strength of sample was larger for lower Si/Al ratio of reaction product formed in sample. According to the correlation between Si/Al ratio and strength in this study, it is expected that if a chemical additive is used for lowering the Si/Al ratio of reaction product(i.e., increasing the $Al_2O_3$ solubility) in alkali-activated K-FA blends binders, strength improvement in K-FA blends binders could be achieved.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.35-41
• /
• 2011

In this study, the interface soaking effect in InAs/GaAs strained-layer superlattice (SLS) on crystalline phase modulation has been analyzed by the x-ray diffraction (XRD) curve. The strain variation induced by As and/or Sb soaking was determined by the separation angle between the substrate peak and the 0th-order superlattice satellite peak in the XRD spectra. Contrated that the As/InAs soaking arises minor GaAs-like interfacial layer, the Sb/GaSb soaking induces InSb-like one. The Fourier-transformed curves of the Pendellosung interference oscillation shows that the optimum soaking times of As/InAs and Sb/GaSb are 2 sec and 12 sec, at which the highest crystallineity has, respectively. An anomalous twin-peak phenomenon that a satellite peak splits into two peaks was observed in the SLS structure co-soaked by As and Sb at InAs${\rightarrow}$GaSb interfaces. We suggest that it may be resulted from coexistence of two kinds crystalline phases of InAsSb and GaAsSb due to intermixing of In${\leftrightarrow}$Ga and Sb${\leftrightarrow}$As.

• Economic and Environmental Geology
• /
• v.46 no.6
• /
• pp.477-484
• /
• 2013

In order to recover gold from iron-hydroxide in acid mine drainage, a lead-fire assay has been used. Acid mine drainage is generated from mining waste rocks, and iron-hydroxide precipitates from acid mine drainage, which severely contaminates the area surrounding the mine. Iron-hydroxide samples contain on average 520.29 mg/kg of Fe, 4,414.62 mg/kg sulfur, and 16.19 mg/kg Au. In an XRD analysis, quartz and goethite were observed along with the iron-hydroxide. Using a lead-fire assay, the recovery of pure gold was on average 0.174 g/ton from the iron-hydroxide, whereas the gold not recovered in the process was on average 1.37 mg/kg. This unrecovered gold was lost to the glass slag due to the galena and lead formation. The galena and lead in the glass slag was identified through XRD.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.188-192
• /
• 2016

In this work, the SiC powders were synthesized through the carbonized matter from the mixture of silica powder and rice husks. The SiC powders, obtained from the carbothermal reduction reaction of silica and carbonized rice husks, were investigated by XRD patterns, XPS, FE-SEM and FE-TEM. In the XRD patterns, the specimens showed clearly very high strong peak of (111) plane near $35^{\circ}$ as well as weak (220) and (311) peak respectively at approximately $60^{\circ}$ and $72^{\circ}$. Under Ar atmosphere, the power synthesized from the mixture (in case of mixing ratio, 6 : 4) of carbonized rice husks and silica showed mainly cubic SiC crystalline phase showing relatively lower ratio of hexagonal phase without residual carbon in XRD pattern. In the TEM analysis, the specimen, synthesized from carbonized rice husks and silica with mixing ratio of 6 : 4 under Ar atmosphere, showed relatively fine particles under $5{\mu}m$ and a crystalline SiC phase of (100) diffraction pattern.