• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.424-424
• /
• 2008

Dye-sensitized Solar Cell (DSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The electric potential distribution in DSCs has played a major role in the operation of such cells. Models based on a built-in electric field which sets the upper limit for the open circuit voltage(Voc) and/or the possibility of a Schottky barrier at the interface between the mesoporous wide band gap semiconductor and the transparent conducting substrate have been presented. $TiO_2$ thin films were deposited on the FTO substrate by Nd:YAG Pulsed Laser Deposition(PLD) at room temperature and post-deposition annealing at $500^{\circ}C$ in flowing $O_2$ atmosphere for 1 hour. The structural properties of $TiO_2$ thin films have investigated by X-ray diffraction(XRD) and atomic force microscope(AFM). Thickness of $TiO_2$ thin films were controlled deference deposition time and measurement by scanning electron microscope(SEM). Then we manufactured a DSC unit cells and I-V and efficiency were tested using solar simulator.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.4
• /
• pp.376-390
• /
• 2001

Alveolar bone changes after immediate loading on implants up to one year were observed by means of standard intraoral X-ray measurement which were taken at 3 month intervals. At the same time, bone density changes were observed according to digital subtraction method which is a becoming a more and more promising diagnostic tool for implants. Following results were obtained ; 1. There was no significant difference in the amount of alveolar bone loss implant type, sex and implant diameter, but there was difference according to case selection. In fully bone anchored prostheses cases, bone loss was $1.16{\pm}0.15m$ whereas, in partial edentulous cases, it was $1.84{\pm}0.08mm$. 2. Alveolar bone loss after immediate loading showed a higher degree of bone loss than after submerged loading in the initial three months. But there were no significant difference at the 12th month. 3. According to the one year bone density change observation at the alveolar bone surrounding the implant, significant change was observed vertically, whereas no significant change could observed horizontally. According to the above mentioned results, we can conclude that immediate loading of implants results in a higher degree of alveolar bone loss in one year than submerged loading. But since alveolar bone loss rate decreases to a reasonable rate after the initial 3 months of rapid bone loss, immediate loading of implants seems to be an acceptable treatment modality for patients with good bone conditions. Fully bone anchored cases showed an favorable outcome, but partial edentulous cases showed more bony resorption. So this cases considered in case selections. Bone density changes observation in the study was performed for only one year therefore a more longitudinal observation may be studied.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1541-1550
• /
• 1997

Since the ceramic/metal joint material is made at a high temperature, the residual stress develops when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of Si$_3$N$_4$STS304 joints quantitatively and to compare the strength of joints. The difference of residual stress is measured when repeated thermal cycl is loaded, under the conditions of the practical use of the ceramic/metal joint. The residual stress increases at 1 cycle of thermal load but decreases in 3 cycles to 10 cycles of thermal load. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a result, it is known that the stress of joint decreases as the number of thermal cycle increases.

• The Journal of Korean Physical Therapy
• /
• v.26 no.2
• /
• pp.56-61
• /
• 2014

Purpose: The aim of this study was to investigate relationship between the angle of the first metatarsophalangeal joint (1st MPJ) and the dimensions of the abductor hallucis; dorso-plantar (DP) thickness, medio-lateral (ML) width, and cross-sectional area (CSA), in subjects with and without hallux valgus. Methods: Sixty feet, mean (SD) age of 22.5 (2.1) years old, were included in this study (hallux valgus = 30; control = 30). An X-ray device was used for measurement of the angle of the 1st MPJ, and an ultrasound system was used for determination of mean (SD) DP thickness, ML width, and CSA of the abductor hallucis muscle in each foot from three trials. Results: The results showed the DP thickness, ML width, and CSA of the abductor hallucis did not differ significantly between subjects with and without hallux valgus. In addition, the correlations between the angle of the 1st MPJ and DP thickness, ML width, and CSA of the abductor hallucis showed poor correlation (Pearson r=-0.09, -0.20, and -0.18, respectively). Conclusion: Based on these findings, we speculate that morphological changes to the abductor hallucis muscle cannot be representative of the angle of the 1st MPJ, and also cannot be used in differentiation between subjects with and without hallux valgus.

• The Korean Journal of Food And Nutrition
• /
• v.20 no.4
• /
• pp.450-459
• /
• 2007

This study was performed to assess the relationships between bone mineral density(BMD), anthropometric measurements, and maternal factors in postmenopausal women. The anthropometric measurements were taken by a trained practitioner, and the maternal factors of the 85 subjects in Chungnam were acquired by an interview questionaire. The BMDs of the lumbar $spines(L_2-L_4)$, femoral necks(FN), ward's triangles(WT), and trochanters(TR) were measured by dual energy X-ray absorptiometry(DEXA). The BMDs(T-score) for $L_2-L_4$, FN, and WT were 0.996 $g/cm^2$(-1.601), 0.697 $g/cm^2(-1.657)$, and 0.793 $g/cm^2(-1.512)$ respectively, which were assessed as osteopenia by the T-score ; TR was noma1 at 0.718 $g/cm^2(-0.675)$. The 85 subjects in Chungnam were divided into three groups according to their BMD measurements for $L_2-L_4$ and FN, assessed by the T-score. The percentages in the osteoporosis, osteopenia, and normal groups were 32.9%, 42.4, and 24.7%, respectively. The average age was significantly the highest in the osteoporosis group than in the other two osteopenia and normal group(p<0.001). The subjects' BMDs were positively correlated with weight, height, BMI, waist, WHR, OBR and hip circumference, and negatively correlated with the age, duration time after menopause, lactation, the age of last delivery, menarche age, and number of children. The average age at menopause was 48.8. The osteoporosis group's average age at menopause was lower than those of the other groups. However, the BMD of the lumbar spine positively correlated with duration time after menopause and the BMD of the femoral neck with lactation, last delivery, menarch age, number of children. Therefore, researches are needed to find out the effective way to minimize the effect of age and other physiological conditions on the decrease of bone mass density.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.2
• /
• pp.121-129
• /
• 1996

The solubility of Ti in Al matrix was determined by X-ray diffraction method on two different mechanical alloying systems, i.e Al+$Al_3Ti$ and Al+Ti alloys. Starting powder compositions of two systems were chosen for final volume fraction of $Al_3Ti$ phase being 25%. The solubility of Ti in ${\alpha}$-Al was estimated by the lattice parameter measurement of Al. For Al+$Al_3Ti$ mixture, it appeared that some of $Al_3Ti$ particles decomposed during milling and maximum solubility of Ti in Al was about 0.99%. The majority of $Al_3Ti$ particles were dispersed uniformly in Al matrix, having approximate size of 100~200 nm. On the other hand, higher Ti solubility of 1.24 wt.% was found in Al+Ti system, with starting composition of Al+10 wt.%Ti. After 15 hours of milling, Ti phase was identified as 20 nm sized particles embedded in Al matrix. The annealing of mechanically alloyed powders from Al+$Al_3Ti$ and Al+10 wt.%Ti systems was followed in the temperature range of 200 to $600^{\circ}C$ to study thermal stability of supersaturated solution of Al(Ti). After annealing, the lattice parameter of Al reverted back to that of pure Al, and the peak intensity ratio of $Al_3Ti$/Al was increased more than the original value before annealing. These results suggest that Ti dissolve into alpha-Al solutions during milling, and by annealing, $Do_{22}-Al_3Ti$ phase forms from Al(Ti) solution.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.24-34
• /
• 1992

Recent studies dealing with the fundamental understanding and applications of bimetallic catalysts are discussed. Bimetallic catalysts have had a major industrial impact, specifically for the reforming of petroleum naphtha, for the hydrogen reduction of carbon monoxide, and for the three way catalytic converter system. The action of the bimetallic catalysts in these reactions may be interpreted in terms of ensembles, electronic influences and surface structure. Various combinations of metal pairs have been considered in order to evaluate the role played by the added metals. For catalyst selectivity control, the possibility of surface enrichment of one element has been recognised. More generally, the influence of preparative variables on the formation of supported catalysts has been clarified, In particular by temperature programmed reduction (TPR). Information on the structure of bimetallic catalysts has been obtained with chemical probes, such as chemisorption and reaction rate measurement and physical probes, such as extended X-ray absorption fine structure (EXAFS), scanning transmission electron microscopy (STEM) and Xe-NMR.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.212-218
• /
• 2013

A transfer method of neutron radiography was developed to measure the size of the end plug and a gap of an intact K102L-2, the irradiated fuel of a ballooned K174L-3, a ballooned and ruptured K98L-3. A typical irradiation time of 25 min. was determined to obtain a film density of between 2 and 3 of SR X-ray film with neutrons of $1.5{\times}10^{11}n{\cdot}cm^{-2}$. To validate and calibrate the results, a RISO fuel standard sample, Cd plate and ASTM-BPI/SI were used. An activated latent image formed in the $100{\mu}m$ Dy foil was subsequently transferred in a dark room for more than 8 hours to the SR film which is a maximum of three half-lives. Due to the L/D ratio an unsharpness of $9.82-14{\mu}m$ and a magnification of 1.0003 were given. After digitizing an image of SR film, the ballooning gap of the plug was discernible by an H/V filter of image processing. The gap size of the ballooned element, K174L-3, is equal to or greater than 1.2 mm. The development of a transfer method played a pivotal role in developing high burn-up of Wolsung and PWR nuclear fuel type.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.202-202
• /
• 1999

The Polyethylene (PE), Polystyrene (PS) and Polytetrafluoroethylene (PTFE) surface modification was investigated by hydrogen io assisted reaction (H-IAR) in oxygen environment. The IAR is a kind of surface modification techniques using ion beam irradiation in reactive gas environment. The energy of hydrogen ion beam was fixed at 1keV, io dose was varied from 5$\times$1014 to 1$\times$1017 ions/$\textrm{cm}^2$, and amount of oxygen blowing gas was fixed 4ml/min. Wettability was measured by water contact angles measurement, and the surface functionality was analyzed by x-ray photoelectron spectroscopy. The contact angle of water on PE modified by argon ion beam only decrease from 95$^{\circ}$ to 52$^{\circ}$, and surface energy was not changed significantly. But, the contact angle using hydrogen ion beam with flowing 4ml/min oxygen stiffly decreased to 8$^{\circ}$ and surface energy to 65 ergs/cm. In case of PS, the contact angle and surface energy changes were similar results of PE, but the contact angle of PTEE samples decreased with ion dose up to 1$\times$1015 ions/$\textrm{cm}^2$, increased at higher dose, and finally increased to the extent that no wetting was appeared at 1$\times$1017 ions/$\textrm{cm}^2$. These results must be due to the hydrogen ion beam that cleans the surface removing the impurities on polymer surfaces, then hydrogen ion beam was activated with C-H bonding to make some functional groups in order to react with the oxygen gases. Finally, unstable polymer surface can be changed from hydrophobic to hydrophilic formation such as C-O and C=O that were confirmed by the XPS analysis, conclusionally, the ion assisted reaction is very effective tools to attach reactive ion species to form functional groups on C-C bond chains of PE, PS and PTFE.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.59-65
• /
• 2001

Epoxy/$BaTiO_3$composite capacitor films with excellent stability at room temperature, uniform thickness, and electrical properties over a large area ware successfully fabricated. The composite capacitor films with good film formation capability and easy process ability were made from epoxy resin developed for ACF as a matrix and two kinds of $BaTiO_3$powders as fillers to increase the dielectric constant of the composite film. The crystal structure of the powders and its effects on dielectric constant of the films were investigated by X-ray diffraction (XRD). And the optimum amount of dispersant, phosphate ester, was determined by viscosity measurement of suspension. DSC and dielectric property tests were conducted to decide the right curing temperature and the optimum amount of the curing agent. As a result, the capacitors of 7 $\mu \textrm{m}$ thick film with 10 nF/$\textrm{cm}^2$ and low leakage current were successfully demonstrated.