• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.1
• /
• pp.413-419
• /
• 2011

Diagnosis X-ray equipment localized at 1950's but it is developed suddenly at 1960's with demand together. Manufacture of Diagnostic X-ray equipment is controled by the KS regulation and the Ministry of Health and Welfare because of hazardous element etc. exposure by radiation. Most of diagnostic X-ray equipment ware single phase and three phase full-wave rectification but from 1980's it transforms it was exchanged in inverter type X-ray equipment. Inverter type X-ray equipment produces approximately 50~80% more average photon intensity then single phase full-wave rectification and the accuracy is high. But from a clinic it dose not use because expensive therefor the efficiency improvement of single phase full-wave rectification is necessary. We produced single phase full-wave rectification X-ray equipment control unit, high tension transformer, filament heating transformer, rectification circuit, high tension cable and others and evaluated efficiency, in result which is excellent compare with Rule of Safety Management and KS regulation.

• The Journal of the Korea Contents Association
• /
• v.10 no.9
• /
• pp.267-275
• /
• 2010

Quality management of an x-ray unit drastically differs according to the type of establishment of medical institutions. Many primary medical institutions have it, but they do not pay much attention to quality management. In the study, Gyeongbuk area has been divided into four zones from January 4, 2010 to September 3, 2010, and four places were designated by city. Among medical institutions located at a total of 16 sites, the target was 8 places with X-ray emission equipment 10 years or more in use as well as 8 places with X-ray emission equipment less than 10 years in use. The 5 essential items of quality control were tested. In the test that checked for equipment it was found that sites with X-ray emission equipment 10 years or more in use didn't have ground connection (6.25%) while all of them passed the current leak test. In the exposure dose reproducibility test 4 sites with X-ray emission equipment 10 years or more in use (25%) and 1 site with X-ray emission equipment less than 10 years in use didn't pass the test. In the KVp accuracy test 5 sites with X-ray emission equipment 10 years or more in use (31.25%) and 2 sites with X-ray emission equipment less than 10 years in use (12.5%) didn't pass the test. In the tube current and tube current amount test 3 sites with X-ray emission equipment 10 years or more in use (18.75%) and 1 site with less than 10 years in use (6.25%) didn't pass the test. According to the findings of the present research, quality control at medical institutions with X-ray equipment 10 years or more in use was poorer than medical institutions with X-ray equipment less than 10 years in use. In this regard, administrative and technical measures need to be taken as soon as possible. In addition, owners of medical clinics or unit managers need to raise awareness, and it is necessary to revise a regular test cycle every year or every two years if they have old equipment or if the equipment is not used on a frequent basis. And it is also important to provide regular educational programs for quality management.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.77-78
• /
• 2013

진단용 X선 투시촬영장치는 고전압발생장치를 필요로 하며, 이에 대용량 전원설비를 갖춘 X선 고전압 발생장치의 개발이 요구되고 있다. X선 투시촬영장치는 단시간 고출력의 촬영과 장시간 저출력의 투시가 가능해야 하므로 고용량의 상용 AC 전원을 사용해야 한다. 이에 본 논문에서는 EDLC를 에너지 저장장치로 사용하여 저용량의 AC전원만으로 투시 및 촬영이 가능한 X선 투시촬영장치용 고전압발생장치를 제안한다. 에너지 저장장치를 기반으로 한 32[kW]급의 X선 투시촬영장치용 고전압발생장치를 구성하고 시뮬레이션 통하여 제안한 고전압발생장치의 효용성을 입증한다.

• Journal of dental hygiene science
• /
• v.15 no.3
• /
• pp.254-258
• /
• 2015

To compare the stationary dental X-ray generator and the portable dental X-ray generator and to understand spatial radiation dose depended on locations by measuring spatial radiation dose of the portable dental X-ray generator. The researchers used an Ionization chamber to measure spatial radiation dose which was generated while applying X-ray radiation to real bone skull phantom with both portable and stationary dental X-ray generator. There were 4 measurement locations which were immediate anterior, right, left and posterior. Distance of measurement was 50 cm in every location and the recorded result is an average of two applications of X-ray radiation to the maxillary molar area under the condition of 70 kVp, 3 mA, 0.1 sec. Average spatial radiation dose of portable X-ray generator was $37.51{\mu}Sv$, much higher than that of stationary X-ray generator which was $10.77{\mu}Sv$ (p<0.001). The result of the spatial radiation dose of the portable X-ray generator showed a huge difference depending on types of units which varied from $17.77{\mu}Sv$ to $68.90{\mu}Sv$ (p<0.05), also depending on the measurement location, immediate anterior resulted in the highest radiation dose of $54.14{\mu}Sv$ and immediate right was the lowest of $13.60{\mu}Sv$. Immediate left and posterior, however, resulted in similar radiation dose which were $42.12{\mu}Sv$, $40.18{\mu}Sv$ (p<0.01). With this result, we claim that usage of portable dental X-ray generator should be restricted to patients who can't move and exposure to radiation should be minimized by wearing lead-apron.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.263.1-263.1
• /
• 2013

탄소나노튜브(CNT)를 이용한 초소형 X선 튜브는 근접 암치료, 비파괴 X선 영상 장치, 휴대용 X선 분광계 등에서 X선 발생소스로 많이 연구되고 있다. 2극형 CNT 에미터의 경우 구조가 단순하여 초소형 X선 튜브에 쉽게 장착할 수 있지만 아노드의 전압과 전류가 연동되기 때문에 튜브의 조작성이 제한적이다. 3극형은 상대적으로 복잡한 구조이고, CNT에서 방출된 전자가 게이트 전극으로 흐르는 누설 전류 그리고 절연체와 충돌하여 차징을 발생시킬 수 있기 때문에 직경이 좁은 초소형 X선 튜브에 구현하기가 쉽지 않다. 하지만 초소형 X선 튜브를 다양한 X선 장치에 응용하기 위해서는 아노드 전압과 전류의 독립된 조작이 가능한 3극형 CNT 에미터가 반드시 구현되어야 한다. 본 발표에서는 전자빔의 아노드 집속을 강화하고 절연체에서의 차징을 줄이는 포커싱 기능의 게이트(FFG) 구조를 제안하였고. 이를 적용하여 초소형 X선 튜브들을 제작하고, 분석하였다. FFG 구조가 성공적으로 적용된 초소형 X선 튜브는 게이트 누설 전류 없이 뛰어난 전류 및 X선 방출 특성을 보였다. 이와는 달리, 몇몇 초소형 X선 튜브들에서는 게이트 누설 전류가 나타났고, 아노드 전압에 의한 게이트 전압 상승이 발생하여 불안정한 구동 특성을 보였다. 초소형 X선 튜브를 밀봉하지 않고 진공 챔버에서 실험한 결과, 유도된 게이트 전압은 상당한 시간이 흐르거나 진공챔버에 공기를 주입하고 다시 진공상태로 만들면 유도전압이 제거되는 것을 볼 수 있었다. 결론적으로 CNT에서 방출된 전자빔이 정상궤도를 벗어나 게이트 누설전류와 차징에 의한 게이트 유도전압을 발생시키면 초소형 X선 튜브가 불안정한 구동을 하고, 결국 튜브의 심각한 결함으로 나타나게 된다. 즉, 게이트 누설 전류와 유도된 게이트 전압은 3극형 CNT 에미터가 장착된 초소형 X선 튜브의 디자인과 제작에 있어서 성공 기준이 될 수 있다.

• Progress in Medical Physics
• /
• v.13 no.3
• /
• pp.169-175
• /
• 2002

The purpose of this study is to verify the usefulness of X-ray simulator which uses a visible light source for further study. We developed a small experimental equipment which is composed of three main components - source, localizer and detector. Cartesian coordinate was set in 3D space, and the position of target was assumed the origin of the coordinate. The light from the source passes directly through the target, and projection image is formed on the screen, which can be taken with the digital camera. Since projection images were acquired behind the screen, they were flipped over right and left. By examining the characters of visual light source and equipments, it could be concluded that developed system was useful for experimental purpose.

• Journal of the Korean Society of Radiology
• /
• v.9 no.3
• /
• pp.131-137
• /
• 2015

The purpose of this study is to warm up the conventional X-ray table by inventing and design for X-ray table with an attached heating device using less unloaded X-ray, CNT (carbon nano tube) heating element. Configuration of the product design for adhesive carbon heating element X-ray is composed of a conventional X-ray table, carbon nano tube planar heating element, an electrode line, flame resisting protective film, and the bottom film. Characteristics and advantages of this invented product is to provide gentle feeling, the sense of security, and eliminating anxiety to the patient wearing a patient gown and feel the cool air while receiving the test. Thus we are strongly recommend to use this device in the clinical situation.

• Journal of radiological science and technology
• /
• v.27 no.4
• /
• pp.23-29
• /
• 2004

The application of analytical model(Archer et al. 1983) to shielding calculations in diagnostic radiology combined with measurements of the broad beam transmission properties of lead, steel, concrete, and plate glass for x-ray tube potential of 60-140 kVp using an x-ray inverter generator and total initial beam filtration sufficient to provide half-valve layer representative of those found in common practice and required by regulatory agencies. Our transmission measurements and numerical fits to the mathematical model of broad beam transmission(Archer et al. 1983) will assist medical or health physicist faced with the task of designing protective barriers for medical diagnostic x-ray facilities.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.108.1-108.1
• /
• 2014

제품의 고성능 사양을 위해 초미소 크기(Nano Size)의 구조를 갖는 제품들이 일상에서 자주 등장한다. 대표 제품은 주변에서 쉽게 접할 수 있는 전자제품의 반도체 칩이다. 반도체 칩 소자 구조는 크기를 줄이는 것 외에도 적층을 통해 소자의 집적도를 높이는 방향으로 진화를 하고 있다. 복잡한 구조로 인해 발생되는 여러 반도체 결함 중에 TSV 결함은 현재 진화하는 반도체 칩의 구조를 대변하는 대표 결함이다. 이 결함을 효율적으로 검출하고 다루기 위해서는 초미소 크기(Nano Size)의 결함을 비파괴적인 방법으로 가시화하고 분석하는 장비가 필요하다. X-ray 시스템은 이러한 요구를 해결하는 훌룡한 한 방법이다. 이 논문에서는 X-ray 시스템의 구성 및 위의 TSV 결함을 검출하고 분석하기 위한 시스템의 특징에 대해 설명을 한다. X-ray 시스템은 크게 X선을 발생시키는 X선튜브와 대상 물체를 투과한 X선을 영상화하는 디텍터, 대상물체의 영상화를 위해 물체를 적절하게 구동시키는 이동장치로 구성되어 있다. 초미소크기(Nano Size)의 결함 검출을 위해서는 X선 튜브, 디텍터, 이동장치에 요구되는 사양의 복잡도, 정밀도는 이러한 시스템의 개발을 어렵게 만든다. 이 논문에서는 이러한 시스템을 개발 시에 시스템 핵심 요소의 특징을 분석한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.762-763
• /
• 2010

The X-ray device used for medical treatment is classified into fixed type that is used by installing at the location with the stable power supply and mobile type that can be taken by moving the X-ray device to the location where a patient is. Mobile X-ray device which is typically used in the mobile type of X-ray can be used very usefully beyond the space restriction. However, due to its difficulty to generate high-voltage, it is mainly applied to take hand and foot shootings which only need low output power. In this study, by designing and producing the large volume of mobile X-ray device which doesn't have the limitations on diagnostic areas of the body, the operating characteristics of device according to the loading change was identified.