• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.47-50
• /
• 2006

High-speed machining is a very useful tool and one of the most effective rapid manufacturing processes. This study sought to produce various high-speed machining materials with excellent quality and dimensional accuracy. However, high-speed machining is not suitable for microscale thin-walled structures because the structure stiffness lacks the ability to resist the cutting force. This paper proposes a new method that is able to rapidly produce very thin-walled structures. This method consists of high-speed machining followed by filling. A strong work-holding force results from the solidification of the filling materials. Low-melting point metal alloys are used to minimize the thermal effects during phase changes and to hold the arbitrarily shaped thin-walled structures quickly during the high-speed machining. We demonstrate some applications, such as thin-walled cylinders and hemispherical shells, to verify the usefulness of this method and compare the analyzed dimensional accuracy of typical parts of the structures.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.55-61
• /
• 2004

Numerical simulations were conducted in a rectangular scramjet combustor with a cavity and/or a step in order to investigate their performances for flame-holding. Flow structures and OH radical profiles in the cavity and the step were calculated. The calculated results showed that the cavity generated a larger recirculation zone than the step that had the same depth. Additionally, the combustor with a cavity could make a large low-velocity area than the combustor with a step. The cavity performance was determined by its depth and length. The cavities with too large or too short length did not work effectively, and a certain aspect ratio showed high performance for flame-holding. There was a minimal depth under which the cavity did not work as flame-holder. The fuel injections upstream the cavity and inside the cavity were also tested to investigate the effects on the cavity performance. The result showed that the fuel injection inside the cavity reduced reaction areas and residence time. Therefore, the upstream injection was preferable to the inside injection.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.33 no.4
• /
• pp.84-90
• /
• 2022

Personal life and achievements are the process and result of a person's past, present, and future interacting with each other. In this regard, if one fully understands the life and background of the person who developed the theory of psychoanalysis, one can understand and use the theory more appropriately. The holding environment theory developed by Donald Woods Winnicott is useful for understanding the process by which infants grow healthy under the care of a mother who is good enough. In this paper, the background of the birth of the holding environment theory is reviewed based on Winnicott's developmental background and marital life. He grew up with a holding environment from good enough 'multiple mothers'. Born with excellent athletic ability and musical talent, he was more curious than anyone else and particularly active in discovering new things. After the unhappy first marriage, Claire Britton's second marriage was happy academically and personally. Claire was a fellow paediatric psychoanalyst who published Winnicott's research and theories after his death. Psychoanalysis or psychotherapy itself can be a holding environment, and the holding environment theory can be applied to various fields in the digital era.

• Journal of the Korean Society of Safety
• /
• v.26 no.3
• /
• pp.69-74
• /
• 2011

Despite most of tasks in manufacturing, construction and agriculture, etc., were currently mechanized and automated, manual materials handling still existed in atypical working condition. In case of manual materials handling, repetitive work, inappropriate working posture, excessive force, contact stress might cause overload, which could lead to work-related musculoskeletal disorders and low back pains. On this basis, the goal of this study is to reveal the effects of various lifting postures of trunk angles and lower extremity postures on maximum holding time(MHT). Twenty two subjects were recruited from a university population. The experiment was designed by a combination of three trunk angle ($0^{\circ}$, $20^{\circ}$, $60^{\circ}$) and three lower extremity postures(straight, bent, kneeling). Before experimental trials, subjects performed MVC(maximum voluntary contraction) exertions in three trunk angles ($0^{\circ}$, $20^{\circ}$, $60^{\circ}$) to calculate 30%MVC at designated postures. In each trial, they were required to hold the handheld load(30%MVC) for a designated posture as long as they could. The results of MVC by trunk angles were measured in $0^{\circ}$ > $20^{\circ}$ > $60^{\circ}$ orders, but those of MHT measured in $20^{\circ}$ > $0^{\circ}$ > $60^{\circ}$ orders. These results showed that straight posture is the ideal working posture in work exerted a strong force for a short time, but the ability to work might be improved in the trunk angle $20^{\circ}$ in work required 30%MVC for a long time. Also, results of MVC and MHT by lower extremity postures measured in straight > bent > kneeling orders.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.93-95
• /
• 2003

YBa$_2$Cu$_3$O$_{x}$ (Y123) single crystal was grown by TSMG (top seeded melt growth) method. Physical properties of Y123 single crystal were dependent on the shape and distribution of Y2BaCuOx (Y211) in it and on the oxygenation temperature and the holding time. In this work, It was investigated to an optimal oxygenation condition and a dependence of melting temperature and holding time on physical properties. The optimal oxygenation condition was found that it was heat-treated for 30 hours at 45$0^{\circ}C$, Also it was found that the critical current density and the size of Y211 were increased with the melting temperature and the holding time.e.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.202-207
• /
• 1993

A theoretical and experimental study is presented for the force holding control of a miniature robotic ringer which is driven by a pair of piezoelectric unimorph cells. In the theoretical analysis, one finger is modeled as a flexible cantilever with a tactile force sensor at the tip and the mate of the finger is a solid beam supposed with sufficient stiffness. Further, the force sensor is modeled by a one-degree-of-freedom, mass-spring system and the output of sensor is then described by the sensor stiffness multiplied by the relative displacement. The problem investigated in this paper is that two typical holding tasks of the human finger are picked up and applied to the robotic finger. One is the work holding a stationary object with a prescribed, time-varying force and the other one is to keep the contacted force constant even if the object is in motion. The simple PID feedback control scheme is used to control the minute gripping force of order 0.01 Newton. It is shown both experimentally and theoretically that the artificial finger with the piezoelectric actuator works well in the minute force holding of the tiny object.

• Journal of Power System Engineering
• /
• v.4 no.3
• /
• pp.81-85
• /
• 2000

The surface gloss of the injection molded part is one of the most significant point for evaluation the quality of products appearance. The effects of molding condition on the gloss of HIPS(High Impact Poly Styrene) molded part were investigated in this work. The measurements of gloss on the surface of molded part were carried out with different melt temperature, mold temperature, injection pressure and holding pressure. We observed the result of HIPS gloss compared with our's previous ABS study. The more melt and mold temperature increased, the brighter the gloss increase. Holding and injection pressure had little effect on the gloss. The gloss was effected in order of melt temperature, mold temperature, injection pressure, holding pressure.

• Korean Journal of Social Welfare
• /
• v.41
• /
• pp.93-118
• /
• 2000

The purpose of this study was to introduce major contents and examine the feminist social work practice. Feminist social work practice has never been introduced and applied to social work fields in Korea. By contrast, it has been developed and expanded in advanced Western countries. Feminist social work was emerged under the influence of worldwide Women's Movement on the end of 1960's. After the time, there were critics of existing social work practice by feminist, increase in interest of women's issues, development of principles and methods in feminist social work practice. Feminist social work practice brought, transformative change, application of gender perspectives to social work practice. Also, it offered the visions for 'integrative practice', accepted the alternative principles and methods, and enriched 'theory-practice'. As the result, feminist social work practice contributed to solving or alleviating the problems of many clients, especially women clients. These evidences suggest that feminist social work practice has the possibility of holding an position as a new alternative social work practice.

• Journal of the Korean Home Economics Association
• /
• v.36 no.9
• /
• pp.139-152
• /
• 1998

The purpose of this study was to examine interactive effects of gender idelogies on the amount of household work time and the perception of fairness in household work by the couples. The data were collected from 100 couples in Seoul and 142 in Taejon. The Major findings were as follows: Interactive effects of gender idelogies had an important role in explaining household work time and the perception of fairness by husbands. For men holding more egalitarian gender idelogies who were married to women being more egalitarian tend to perform more hours of household work. And husbands who had traditional gender ideologies percept relatively fair to the couples' division of household work. It was approved that wives had a primary role in the division of household work.