• Journal of the Korean Wood Science and Technology
• /
• v.23 no.2
• /
• pp.77-82
• /
• 1995

With the aim to utilize pine wood(Pinus densiflora Sieb. et Zucc.) as an interior building materials, such as flooring material, monoethylene glycol(MEG) resin solution was impregnated into greenwood. Specimens of three different qualities, that is, normal wood, resinous wood and compression wood, were prepared. Distribution of resin element(phosphorus) in MEG resin solution-impregnated woods and preservative effectiveness against brown rot fungi(Tyromyces palustris and Serpula lacrymans) of these woods were investigated. The results were as follows: 1. The concentration of phosphorus into cell walls of resinous wood and compression wood was lower compared to that of normal wood. This shows that the quality of wood has an influence on the penetration of MEG resin solution into the wood. It was shown from a leaching test that MEG resin could be leached out easily from the cell walls. 2. The resinous wood and compression wood, even without MEG resin solution impregnation had high decay resistance. For normal wood, significant improvement of preservative effectiveness was observed after impregnation of MEG resin solution. It was shown that MEG resin was leached out from the woods after leaching test, resulting in the reduction of preservative effectiveness. From this result, suitability of MEG resin solution-impregnated woods as an interior materials was recognized.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.2
• /
• pp.172-178
• /
• 2011

Three different finger-jointed lumbers which have different geometric features and adhesives were manufactured and studied in this study. Larch and pitch pine lumbers with and without preservative treatment were used. Bending MOE was measured as the preliminary investigation for grouping the specimen. After the finger, bending MOE of two wood species without preservative treatment shows over 97% property of the control group. The tensile modulus also shows almost same property after the finger joint. And it is found out that the preservative treatment induce little effect on bending and tensile MOE. Based on this result, high performance of examined finger-jointed lumber can be found out. However, tensile strength decreased around 20% which would be induced by the crack along the root of the finger which is formed near the edge during manufacturing stage. And finger-jointed lumber with preservative treatment even shows higher decrement of the tensile strength with higher wooden part failure mode.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.497-510
• /
• 2018

In this study, the decay resistance of larch wood, which was heat treated by superheated steam, was evaluated by the field decay test. During the field decay test of 12 months, non-treated wood has been severely damaged by termite, however, no visible damage has occurred in the preservative-treated wood and superheated steam heat-treated wood. Results of field decay test showed approximately 5% mass loss of the non-treated wood and the preservative-treated wood, and approximately 1% mass loss of the superheated steam heat-treated wood. After the field decay test for 12 months, the residual amount of preservatives remaining in the preservative-treated wood was lower than that before the field decay test. It was considered that the preservative was partially eluted during the field decay test, and the mass loss of the preservative-treated wood was thought to be similar to that of the non-treated wood. Through this study and additional long-term monitoring test, superheated steam heat treatment can be considered to be an environmental-friendly method to enhance the decay resistance of wood against rot fungi and/or insect without chemical treatment such as preservative injection.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.521-530
• /
• 2011

Nowadays, market demand of structural Glulam is growing and diversifying. The durability of Glulam should be significantly considered when they are intended to apply for out-door use such as timber bridge and pergola. This study was aimed to develop the manufacturing process of preservative treated structural Glulam using domestic softwood species. 10 m long structural Glulam were manufactured from domestic pitch pine logs with CuAz-3 preservative treatment. At each manufacturing process, the production yield was evaluated. Finally, bending tests were performed to verify the structural performance of manufactured Glulam. From the results, it was shown that the preservative treatment process hardly influenced on the production yield. But domestic pitch pine was proved to not be suitable for making the preservative treated Glulam due to the large difference of preservative permeability between sapwood and heartwood.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.15-22
• /
• 1992

This study was performed to investigate the corrosion of metal fasteners in waterborne preservative-treated wood. Of all the metal tested, steel exhibited the greatest amount of corrosion across all preservatives and exposure conditions whereas stainless steel was totally inert. Galvanized steel corroded at a much lower rate compared to steel and the corrosion of brass was negligible. Among the preservatives, CCA-Type B was the most corrosive system tested. The sequence for the average corrosivity across all metals was: CCA-type B>CCA-Type C${\geq}$ACC${\geq}$CCA-Type A. Across all metals and retentions the salt formulations were more corrosive than the oxide and the corrosion was increased with the increse in the amount of preservative loadings. The amount of corrosion was also increased with the increase in exposure relative humidity (RH) across all metals and presevatives However, at the 60% RH exposure condition, the corrosion of metals was very negligible. Consequently, it can be concluded that across all metals oxide-type preservatives should be used to prevent the corrosion problem of metal fasteners in contact with treated wood and the use of steel nail preservative-treated wood should be avoided without distinction of end-use location, i.e., exterior or interior, and the use of stainless steel or at least brass nail in damp exterior condition was strongly recommended.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.34-40
• /
• 2014

The effect of neonicochid type wood preservatives on adhesive properties of resorcinol-formaldehyde resin for laminated wood manufacture was examined. By the previous studies, it was verified that the neonicochid type preservative has a high termite-proofing and anti-mold effectiveness. Commercial ACQ (ammoniacal copper quaternary compounds) and CUAZ (copper azol compounds) were used as comparison preservatives of effects on adhesive properties. The wood specimens used japanese red pine (Pinus densifrora) after application with preservatives and then bonded with resorcinol-formaldehyde resin. Adhesive properties were evaluated by shearing strength of adhesive bond and wood failure to dry condition or after accelerated aging test. Of all laminated woods, the wood specimens spread with ACQ or CUAZ showed the lowest shearing strength of adhesive bond. We estimated that the decrease of shearing strength was caused by copper in the ACQ or CUAZ preservatives. On the application of the neonicochid type preservatives, the wood specimens showed the highest shearing strength even after accelerated aging test. From these results, it is concluded that the copper-free neonicochid type preservative not affected the curing of resorcinol-formaldehyde resin.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.3
• /
• pp.212-227
• /
• 2012

Current research trends in wood preservatives for enhancing durability was reviewed. Due to leaching of recent Copper-Based Preservatives commonly used as chemicals for pressure treatment; they have been a growing concern, especially in improving the fixation of the copper as alkyl ammonium quat. and azol in wood and preventing the leaching of active ingredients. With the appearance of emulsion type chemicals using micronized and nano-sized wood preservatives, researchs on characteristics of Copper-Based Preservatives regarding penetration and fixation in wood are debatable. Moreover, unlike the case of CCA, the recent alkyl ammonium quat. and azol bear a serious threat in the decrease of antimicrobial effectiveness against wood destroying fungi with copper tolerance. Therefore, development and research of co-biocide is needed.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.3
• /
• pp.253-259
• /
• 2018

To determine the depth of preservative penetration in ACQ treated wood, the degree of penetration of Cu was measured. In this study, we developed a DDAC coloring method to investigate the penetration depth of DDAC, which is one of the active ingredient of ACQ, into wood. The following conclusions were obtained. The DDAC component reacts with a 2', 7'-dichlorofluorescein indicator and results in a deep orange color. This orange coloring reaction appears not only in DDAC solutions but also in ACQ treated wood tissues in which DDAC is present. It is possible to visually verify that DDAC has better wood penetration than Cu in the spruce, which is an refractory wood species, by the DDAC coloring method developed this study. In addition to the results, it is necessary to investigate the difference in penetration of Cu and DDAC for other wood species with poor preservative penetration.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.4
• /
• pp.491-498
• /
• 2014

In order to obtain basic data for concentration control of alkaline copper quat (ACQ) solution in wood preservative treatment, this study investigates the change of concentration and adsorption of treating solution and active ingredient, copper oxide (CuO) and didecyldimethyl ammonium chloride (DDAC), in the process of recycling of ACQ solution. Japanese larch (Larix leptolepis), Douglas-fir (Psedotsuga menziesii) and Radiata pine (Pinus radiata) were treated with ACQ solution. The active ingredient concentration of ACQ solution was decreased continuously with increase of recycling. There are differences between extent of concentration decrease of Cu (as CuO) and DDAC. DDAC was decreased more quickly and to a higher degree than Cu for all recycling. The extent of DDAC concentration decrease was remarkable than that of Cu for wood species. The amount of DDAC adsorbed into wood decreased with the increase of ACQ solution recycling, but adsorption of Cu was little difference regardless of recycling. The adsorption of Cu into wood increased as DDAC concentration decrease by recycling of ACQ solution. This is likely due to decrease of DDAC competition with Cu for the same reaction site in wood.

• Journal of the Korea Furniture Society
• /
• v.19 no.5
• /
• pp.358-364
• /
• 2008

Wood-inorganic material composite (WIC) was prepared by impregnating wood with copper sulfate ($CuSO_4\;5H_2O$) solution and by immersed wood in sodium carbonate($Na_2CO_3$) solution in order to introduce insoluble copper compounds {copper carbonate hydroxide, $CuCO_3\;Cu(OH)_2$} into the wood to give fungicidal effects in treated-wood. The weight percent gains (WPGs) of treated wood reached maximum value by impregnation of 20% copper sulfate solution and immersion in about 15% sodium carbonate solution for 24 hrs. Inorganic substances were present mainly in the lumina and cross-field pitting of tracheides. These substances were proved to be the insoluble copper carbonate hydroxide against water by the energy dispersive X-ray analyzer in conjunction with a scanning electron microscope (SEM-EDXA). The treated specimens showed high preservative effectiveness because the weight losses were hardly occurred by the fungi degradation test.