• Journal of the Korean Wood Science and Technology
• /
• v.22 no.2
• /
• pp.61-70
• /
• 1994

This study was executed to find the applicability of press drying of tree disk by investigating the shrinkage and drying defect and to form appropriate model by comparing the actual moisture content(MC) and internal temperature in respect of drying time with calculated values based computer simulation to which was applied finite difference method. In press drying disk, heating period, constant drying rate period maintained plateau temperature at 100$^{\circ}C$ and falling drying rate period were significantly distinguished. Actual MC and internal temperature were analogous to those calculated at comparing points. Heat transfer model formed by Fourier's law using specific heat of moist wood and conduction coefficient considering fractional volume of each element of wood cell wall, bound water, free water and air showed applicability as basic data to developing heat expansion, shrinkage and drying stress during press drying. Also mass transfer model formed by Fick's diffusion law using water vapor diffusion coefficient showed applicability. Longitudinal shrinkage was developed by pressure of hot press and tangential shrinkage was restrained by hygrothermal recovery. The heart check, surface check and ring failure were occurred differently in species, but V-shaped crack didn't develop.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.24-30
• /
• 1981

This experiment was carried out to determine the drying time from green to oven dry and estimate the moisture content of wood, such as red lauan (Shorea Spp.), Douglas fir (Pseudotsuga menziesii), Birch (Betula platyphylla), and oak (Quercus aliena), at various thickness, paralleled to fiber, of specimen for M.C. by oven dry method (100-105$^{\circ}C$). The results obtained are summarized as follows: 1. The drying time from green to oven dry decreases as the thickness of specimen for M.C. becomes to be thined, and that time at 10mm thickness are 14 hrs, for birch wood and 24 hrs, for oak wood. 2. The relative formulae between thickness (X) of specimen for M.C. and drying lime (Y) from 12% to oven dry are showed in Fig. 3. 3. The M.C. based on the weight of specimen for M.C. at t% can be obtained from the formula (2), and the drying time to 1% are shorter than that time to oven dry by approximately three times.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.5
• /
• pp.456-465
• /
• 2013

Log cross sections of yellow poplar were dried in a radio frequency vacuum (RFV) dryer under alternating vacuum and release (AVR) process. The average moisture content (MC), temperature and vapor pressure at the volumetric center were monitored as functions of time. Three different log thicknesses (33, 60 and 75mm) were tested. The results show that the AVR process caused an increase in the drying rate when the moisture content was above fiber saturation point (FSP, about 30% MC) but that it had an inverse effect on the drying rate when the MC was below FSP. The effect of the AVR process on the drying rate decreased, and the severity of heart checks increased, with the increase in the thickness of the specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.101-111
• /
• 2014

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaining (BR) and bark-remaining-coating (BRC) treatments on the air circulating oven-drying characteristics of Japanese larch hollowed round-post was evaluated. The drying times of the hollowed round-posts for control, VD, HCO and BR specimens were 72, 168, 204 and 240 hours, respectively, from the initial MC to about 8% MC, which was recommended as the indoor in-use MC. The temperature in the hole of the VD specimen was lower than that of wood and the difference between air temperature in the hole and wood temperature became large during drying period. The vapor pressure of air in the hole was higher than that of inside wood for all specimens except VD specimen. The surface checks on all specimens were observed in increasing order of BR, BRC, UC, HCO and VD specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.2
• /
• pp.23-30
• /
• 1992

An experimental external external collector type, solar dehumidification dryer was retrofitted with a simple computer-based control system. Solar, solar-dehumidification, and air-drying of 3cm-thick douglas-fir were carried out to investigate the drying-conditions and characteristics of this system, and to analyze the energy efficiencies of each drying met hods in summer. The drying rate of solar-dehumidification was 12%/day, which was about 2 times and 3 times faster than that of solar-and air-drying, respectively. The amount of diurnal temperature fluctuation inside the solar-dryer was greatly reduced and the energy efficiency was enhanced from 25% to 60% by the dehumidifier.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.5-14
• /
• 1992

Experimental external collector type solar lumber dryer of $1m^3$ of maximum capacity with $1.6m^3$ of collector area was designed and constructed. The seasonal performance of solar dryer, including air-conditions, energy efficiency, and drying characteristics of 3cm-thick red pine and douglas-fir lumber was investigated. Also, the economic analysis was carried out. Annual average solar drying rate was about 2 times faster than air-drying rate with no significant difference in the amount of drying defects. But in initial drying stage air-drying rate in winter was much faster and those in spring and autumn were slightly slower than solar drying rate in each season. Annual average energy efficiency of solar-dryer and-collector was 25% and 57%, respectively. Fuel savings were over 50% at 15% of energy inflation rate and the payback period was estimated as 6.10 years at 30% of energy inflation rate.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.3
• /
• pp.1-8
• /
• 1998

Western redcedar timber, 26 by 26cm in cross section and by 200cm long, was dried in a laboratory radio-frequency/vacuum kiln under 65torr of ambient pressure and a fixed frequency of 6.78MHz for the potential rapidly dry large timber. All process data were collected and saved in a computer through a data acquisition system. The temperature in the middle of timber was higher than temperature at the quarter point of timber length and thickness. Temperature gradients developed in the longitudinal and transverse direction of timber. The pressure in the middle of timber was higher than pressure at the quarter point of timber length. The pressure in the middle of timber was lower in the early stage of drying, and higher in the latter stage of drying than pressure at the quarter point of timber thickness. Power density was very highest during heating period and then gradually decreased. The drying curve was approximately linear and the total drying time was 27 hours from an initial moisture content(MC) of 48.6 percent to a final Me of 19.2 percent with only a few mild internal checks in the middle location of timber.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.2
• /
• pp.20-28
• /
• 2008

This study was carried out to provide the so-called circumferential slicing method for investigating radial distributions of the tangential strains and of moisture contents within the log cross section (LC) of Kalopanax pictus during indoor drying it. While the heartwood showed an almost uniform moisture content distribution in the range of about 50~55% in case of the green wood, it has gradually decreased toward the outer side, showing about 19% of moisture content difference from the innermost slice. Although the moisture gradient along the radial direction has gradually become gentle as drying progresses, the sapwood of the outer side represented the moisture contents below the fiber saturation point after 24 hours of drying while the heartwood in the inner part showed the moisture contents higher than the fiber saturation point. The pith side was laid under the tensile stress after 24 hours of drying, and then gradually decreasing toward the bark side, and showed the distribution being switched again to the tensile stress on the bark side. As the drying has progressed, this trend got more intensified, and finally showed the U-shaped distribution model after 48 hours of drying. The circumferential slice test is considered to be suitable in quantitatively determining the tangential strains and moisture content within a LC.

• Journal of the Korea Furniture Society
• /
• v.27 no.1
• /
• pp.43-48
• /
• 2016

PEG (Polyethylene glycol) impregnation in wood reduces the occurrence of checking during kiln drying. The volumetric shrinkages of wood PEG impregnated by pressure (PEG-P) or soaking (PEG-S) methods, and oven-dried by vent (VD) or air-tight (AD) methods were measured and compared with the controls. The average oven-dry weight of PEG impregnated specimens was larger than that of the controls by 3.6 g, but was not influenced by the drying methods. The average of the total volumetric shrinkage of PEG-P-VD specimens was the least (2.3%), while that of CON-S-AD specimens was the largest (28.9%). Within a drying method the total volumetric shrinkage of the control was the largest followed by PEG-S and PEG-P specimens, which implied that residual PEG in wood restrained its shrinkage during drying.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.726-735
• /
• 2016

This study was carried out to evaluate the high-temperature drying characteristics of douglas-fir, hemlock, and radiata pine square timber with dimensions of thickness 15 cm and 18 cm. As a result, radiata pine showed the lowest final moisture content followed by douglas-fir and hemlock without reference to the timber size. Moreover, when the longitudinal kerfing is processed, the final moisture content was lower than control. The kerfing treatment was effective to decreasing the twist of radiata pine and hemlock. When douglas-fir is processed to the shape like the edge-grained timber that does not include the pith, the decrease of drying defect was possible.