• Journal of the Korea Institute of Building Construction
• /
• v.11 no.2
• /
• pp.162-170
• /
• 2011

As the result of implementing a treated material test and durability test after quickly drying S.P.F. species, a type of softwood structural material, within a short period time, soaking it in liquid phosphate flame proof agent for an hour, microwave heating it, and compressing it from 3.8cm to 1cm, when setting the appropriate heating time of microwave heating at 7 minutes at 5kW, it is observed that it satisfies the target water content (4~5%). It is shown that in a water content measurement of the wood that is compressed after being softened by soaking in the flame proof agent, drying and heating at 3kW for 9 minutes, all specimens satisfied 12~14%, the appropriate water content for exterior wood. Also, it is shown that in terms of the flame performance obtained through a flame resistance treatment of the compressed wood and a treated material test, the specimen soaked in flame proof agent for 30 minutes was the most excellent, and that the performance test result of the compressed wood in all areas, such as nail withdrawal resistance, compression, bending strength, and shearing strength, were all improved in their mechanical features to twice to three times better performances.

• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.1049-1055
• /
• 2012

The fiber mat catalytic burner that uses infrared radiative heat obtained by flameless catalytic combustion was manufactured and tested to investigate its combustion characteristics. About 9 to 17% of combustion heat was released by sensible heat during the premixed catalytic combustion depend on combustion condition. To find out radiation intensity with distance between catalytic burner and sample, the equation that calculate the receiving surface of radiative energy under the fiber mat catalytic burner was driven. This equation was well correlated with the drying rate of melamine. The drying experiments were carried out to the melamine, wood chip and agricultural pallet by using the fiber mat catalytic burner and the energy efficiency was calculated from drying rate of them. The energy efficiency of the fiber mat catalytic burner reaches to 79% in maximum for drying of the wood chip.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.22-40
• /
• 2015

Cellulose fibers is one of the most abundant in nature. It has many distinctive features: abundant in nature, biodegradable, non-toxic, eco-friendly, sustainable, easy to fabricate, hydrophilic, and cost-effective. Cellulose fibers, known as pulp, is produced from cellulose-containing materials by the pulping process. As the raw material, wood has been most commonly used while recycled pulp has been also used to some degree. Thus, pulp usually refers to wood pulp. Generally, the pulp and paper industry is regarded as the commodity market where the cost should be much more important than the quality. It also belongs to a mature market where the growth is slow, or even in decline. Accordingly, technological development has been rather stagnant for the industry. Recently, however, the pulp and paper industry has faced very serious challenges. First, due to digital technology, there has been a steady decline in the need for pulp and paper products. The digital industry has continuously replaced printed products such as books, newspapers, and magazines. Second, there has been a trend initiated by developed countries to limit the use of wood as the raw material for the sake of environmental protection. This forces the industry to find a more efficient use of wood pulp as well as finding alternative, non-wood sources. Third, as an individual becomes wealthier and more conscious of health-care, the quality of a product becomes more important than the cost. Thus, a paradigm shift is needed from the cost-conscientious to the quality conscientious. The objective of this article is to review the technologies aimed at engineering cellulose fibers for producing high-value added paper products.

• Journal of Environmental Science International
• /
• v.17 no.12
• /
• pp.1381-1390
• /
• 2008

Emission characteristics of volatile organic compounds (VOCs) were investigated in the flue gas emitted from wood drying process for plywood manufacturing. The moisture content of raw timber was average 48%, and its density was $831.55kg/m^3$. But the moisture content of dried wood is needed less than around 10%, thus the moisture contents of flue gas should be remarkably high(about 18.2 V/V%). Therefore, the vapor in flue gas is equivalent to 320 ton-vapor/day when 1100 ton-wood/day is treated in the wood drying process. The temperature of flue gas ranges from $140^{\circ}C\;to\;150^{\circ}C$ in each dryer stack with exception of the input site of wood(about $110^{\circ}C$). The velocity of flue gas in each stack ranges from 1.7 to 9.7m/sec. In order to assess the concentrations and attribution rate of odorous compounds, it was analyzed about 40 VOCs in the flue gases. It was found that the major odorous compounds were 8 compounds, and the concentrations of major VOCs(ppm) were as follows; benzene: $0.054{\sim}0.052$, toluene: $1.011{\sim}2.547$, ethylbenzene: $0.472{\sim}2.023$, m,p-xylene: $0.504{\sim}3.245$, styrene: $0.015{\sim}0.148$, o-xylene : $0.271{\sim}1.097$, ethanol: $11.2{\sim}32.5$, ${\alpha}$-pinene: $0.908{\sim}10.578$, ${\beta}$-pinene: $0.982{\sim}14.278$. The attribution rate of terpenes (${\alpha}$-pinene, ${\beta}$-pinene) was about 60.56%, and that of aromatics and alcohols was about 22.77%, and 16.67%, respectively. It is suggested that the adequate control device should be used to control both the water soluble and non-soluble compounds because both compounds were mixed in flue gas.

• Journal of the Korean Wood Science and Technology
• /
• v.4 no.1
• /
• pp.48-53
• /
• 1976

This Study was carried out to investigate the course of air-drying and drying defects of red pine (Pinus densiflora S. et Z.) and Italian poplar (Populus eurameriana I-476) boards 1,2 and 3cm thick in the flat pile. The results are as follows. 1. Air-drying curves for red pine and Italian poplar boards were same as figure 1 and 2. These moisture contents were lower in July and August during seasoning periods. 2. Air drying time of red pine board required to dry 15 percent moisture content in one week for 1 cm board, five weeks for 2 cm board and six weeks for 3cm board respectively. In case of Italian poplar boards, in one week for 1 cm board, four weeks for 2 cm and five weeks for 3 cm board. The thickness of board influenced the time for air drying. 3. Drying defects such as checking, warping and staining happened badly in pine than in Italian poplar boards. Especially, checking was severe in thicker board and warping in thinner board.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.3
• /
• pp.61-66
• /
• 1993

24mm-thick specimens from three species of plantation-grown softwood were press dried under two platen pressures of 1.75kgf/$cm^2$ and 3.50kgf/$cm^2$ to obtain drying information regarding to drying rate, thickness shrinkage and drying defects. The influence of platen pressure on drying fare in range of moisture content (30 to 10 percent) increased for pitch pine and larch, but reduced for korean white pine at higher pressure. Thickness shrinkage was increased at the higher pressure, and estimated thickness shrinkage at final MC of 10 percent became unrealistically greater for specimens containing higher final moisture content under the great influence of compressive strain. The effects of pressure on the amount of surface checks and honeycombing were different from species used. These species should have applied lower temperature than 177$^{\circ}C$ in this study to reduce surface checks and honeycombing.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.6
• /
• pp.512-520
• /
• 2011

This study was preformed to investigate the characteristics of the green drying system for utilizing heat wasted during carbonization process. The green drying system utilizing waste heat is one of environment-friendly equipments because it needs no other energies from fossil fuel and etc. In this study, waste heat from three kilns was collected by stainless connection pipe, and in the green drying system the temperature and humidity was hardly changed. Charcoal charecteristics as fixed carbon, refining degree, hardness, pH, calorific value, and charcoal yield were analyzed to investigate kiln performance due to installation of green drying system. As a result, the green dry system installation hardly affected the characteristics of charcoal. In conclusion, the green drying system can be applied to maximize the profit of the farm household income and contribute to reduce fossil energy.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2001

Red pine (Pinus densiflora), white pine (Pinus koraiensis), larch (Larix leptolepis) and Western hemlock (Tsuga heterophylla) lumber were vacuum-press dried under three drying schedules to investigate current moisture contents (MC), drying rates and drying time factors related to five lumber thicknesses of 3, 5, 7, 9 and 11cm. Current MC could be estimated by drying factors such as lumber thickness, initial Me and drying time. Average drying rate from 30% to 15% Me was the highest for Western hemlock below fiber satuartion point, red pine, white pine and larch in the order of their magnitude. Drying rate curvilinearly decreased as lumber thickness increased. Drying time factor curvilinearly increased as lumber thickness increased.

• Journal of Biosystems Engineering
• /
• v.29 no.3
• /
• pp.261-266
• /
• 2004

This study was Performed to classify the acoustic emission(AE) signal due to surface cracking and moisture movement in the flat-sawn boards of oak(Quercus Variablilis) during drying using the principal component analysis(PCA) and artificial neural network(ANN). To reduce the multicollinearity among AE parameters such as peak amplitude, ring-down count event duration, ring-down count divided by event duration, energy, rise time, and peak amplitude divided by rise time and to extract the significant AE parameters, correlation analysis was performed. Over 96 of the variance of AE parameters could be accounted for by the first and second principal components. An ANN analysis was successfully used to classify the Af signals into two patterns. The ANN classifier based on PCA appeared to be a promising tool to classify the AE signals from wood drying.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.1
• /
• pp.47-57
• /
• 2024

Solar energy is one of the most promising options for renewable energy and biomass is one of them. One of the main biomass sources, sugarcane bagasse, is produced annually in more than hundreds of nations worldwide exceeding 4.25 billion tons. To dry a 900-mm deep fixed bed of wet sugarcane bagasse, a solar air heater with a collector area of 2 m² was installed. Between October 10^th to 19^th in Gwangju, South Korea, a 9-day drying period, the solar collector received a total of 496,145 kJ of solar radiation. During this time, 54.5 kg of water was extracted from 133 kg of wet sugarcane bagasse (average green moisture content of 47.6%_w.b.). The estimated net heat from the evaporation of water removed during the dying period accounted for approximately 27% of the total solar radiation on the solar collector.