• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.521-524
• /
• 2006

Recently, densified pollet fuel from wood biomass is widely used at North America and Europe as a regenerable and clean carbon neutral bioenergy. High-pressure compaction of sawdust of several species of wood to form a densified fuel was studied. Calorific and elemental analysis were carried out to assess pellet fuels Hot-press process was adopted for compact ion of sawdust and compaction was performed under prescribed condition. Densified fuels were evaluated by its oven-dry density and fines after 5-minute shaking test. The target density and fines of densified fuels were over $1.2g/cm^3$ and below 0.5%, respectively. When the press-temperature is over $60^{\circ}C$ densified fuels with density over $1.2g/cm^3$ and with fines below 0.5% can be produced. And the pressure over $1000kgf/cm^2$ was effect ive for this production.

• Environmental Engineering Research
• /
• 제22권3호
• /
• pp.320-328
• /
• 2017

This paper describes the non-isothermal pyrolysis of wood pellet and saw dust, and their blends with bituminous coal. The blends showed the distinct, two peaks in thermogravimetric curves, and the first peak came from the biomass pyrolysis and the second one came from the coal pyrolysis. The interaction in the blend was evaluated in terms of the maximum rate of weight loss, characteristic temperatures, char yields, and the calculated and experimental thermogravimetric curves. The activation energies and frequency factors for the blends were obtained with the multi-stage, Coats and Redfern method. The respective activation energies of 73 and 67 kJ/mol and the frequency factors of 725,100 and $65,262min^{-1}$ were obtained for the present wood pellet and saw dust samples. The thermogravimetric study shows that there is no significant interaction between the present biomass and coal in the blends, and the pyrolysis behavior can be described with the additive rule.

• Journal of the Korean Wood Science and Technology
• /
• 제45권4호
• /
• pp.382-398
• /
• 2017

This study was conducted to identify the potential of Quercus mongolica (QUM), Pinus densiflora (PID) and Pinus rigida (PIR) as a raw material for pellet production. Larix kaempferi (LAK), which has mostly been used for pellet production in Korea, was also used as a control. All specimens contained very minimal amounts of sulfur and chlorine. Ash content of LAK was the lowest, followed by PID, PIR and QUM. For the size distribution, the mass fraction between 0.42 mm and 0.25 mm was the highest in PIR. Most fuel characteristics of the produced wood pellets improved with the use of 12% moisture content (MC) particles and the increase of the ratio of length to diameter of a hole in flat-die (L/D ratio). When the MC, bulk density and durability of QUM, PID, PIR and LAK pellets was compared with the standards of the KFRI and ISO, the use of wood particles of 12% MC and flat-die with an L/D ratio of 5.00 for PID particles are suitable for high-quality pellets in the aspects of all fuel characteristics. For PIR and QUM, further work is needed to seek the optimum conditions for the production of high-quality and durable pellets.

• 한국기후변화학회지
• /
• 제6권1호
• /
• pp.41-47
• /
• 2015

This study was carried out simulating domestic utilization conditions of a wood pellet stove and a wood pellet boiler in order to determine emission factors (EFs) of macro-pollutants, i.e., carbon monoxide, nitrogen oxides, sulfur oxides, ammonia, particulate matters (total suspended particulate, $PM_{10}$, $PM_{2.5}$, black carbon) and trace pollutants (i.e., ten different volatile organic compounds). The composite pollutants EFs for the pellet stove were: for TSP 4.58 g/kg, for $PM_{10}$ 3.35 g/kg, for $PM_{2.5}$ 2.48 g/kg, CO 119.23 g/kg, NO 14.40 g/kg, $SO_2$ 0.17 g/kg, TVOC 37.73 g/kg, $NH_3$ 0.02 g/kg and emissions were similar to the pellet boiler appliance: for TSP 4.73 g/kg, for $PM_{10}$ 3.41 g/kg, for $PM_{2.5}$ 2.63 g/kg, CO 161.51 g/kg, NO 13.67 g/kg, $SO_2$ 0.19 g/kg, TVOC 45.22 g/kg, $NH_3$ 0.02 g/kg.

• Journal of the Korean Wood Science and Technology
• /
• 제51권5호
• /
• pp.381-391
• /
• 2023

Densification is a technique used to improve biomass quality in wood pellet manufacturing and torrefaction treatment. In this study, the effects of torrefaction on the quality of Calliandra wood pellets were investigated, and pellets of Calliandra wood (Calliandra calothyrsus) and bark were evaluated. The study was conducted using a completely randomized design with two treatment factors, namely torrefaction temperature (250℃ and 300℃) and torrefaction duration (30, 45, and 60 min). The results showed that the interaction between temperature and torrefaction duration significantly affected the compressive strength, proximate value, and calorific value of the torrefied Calliandra wood pellets. An increase in the temperature and torrefaction duration decreased the compressive strength, moisture content, volatile matter content, and ash content of the torrefied Calliandra wood pellets. Conversely, the calorific value of Calliandra wood pellets increased with increasing temperature and torrefaction duration. The best-quality Calliandra wood pellets were produced at a torrefaction temperature and duration of 300℃ and 60 min, respectively. In terms of important quality parameters, ash content of 0.90% and calorific value of 6,303.80 cal/g were observed, which complied with the quality standards of Indonesian National Standard 8675:2018 and Deutsche Industrie Norm 51731.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.30-36
• /
• 2006

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a batch type fluidized-bed to investigate the drying characteristics of sawdust as a raw material for bio-fuel. The minimum fluidization air velocity was increased as particle size was increased. It took about 21 minutes and 8 minutes to dry 0.08 m-deep bed of particles with average particle size of 1.3 mm from 100% to 10% moisture content at air temperature of $20^{\circ}C$ and $50^{\circ}C$, respectively.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.503-511
• /
• 2018

There have been many studies of combustion in the circulating fluidized bed. However, little study is available for combustion of wood pellet together fed with wood chip. The mixed ratio of two fuels is an useful information when thermal power company would receive the Renewable Energy Portfolio Standard (RPS) from government. In this study, the combustion behavior and kinetics of such biomass fuels are evaluated using fluidized bed reactor and thermogravimetric analyzers. The mixing ratio of wood chip relative to wood pellet was varied at different temperatures. The results show that a combustion reactivity changed significantly at the wood chip mixing ratio of 40%, particularly at low temperature condition.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.35-41
• /
• 2014

The wood pellet, which is one of the woody biomass energy, has very high economic efficiency and combustion efficiency during their combustion. The existing pellet burner have many problems such as low combustion efficiency, flame stabilization, ash problem and ignition time etc. We developed cyclonic wood pellet burner aim to 20,000kcal/hr boiler and measured temperature profiles and exhaust gases in order to investigate the flame stability and optimum combustion condition at any air flow conditions. As results, we confirmed the reappearance and the isotropy of the experimental results in the burner. At the first air flow inlet condition of excess air ratio ${\alpha}=0.02$, second air flow $490{\ell}/min$ had the best combustion condition when pellet supplied 30g. This result means that we need much air supply only for the swirling of second air flow. So we tested various second air flux at first air excess air ratio ${\alpha}=0.7$ condition. At this condition, we could find out that we don't need much second air and total air flux compared to the former condition. We will continuously test this work of air flow distribution, and swirl effect of first air flow, and ash elimination.

• Journal of the Korean Wood Science and Technology
• /
• 제39권3호
• /
• pp.258-268
• /
• 2011

본 연구는 낙엽송과 백합나무 톱밥을 이용한 펠릿의 제조 과정에서 톱밥의 크기 및 함수율, 펠릿제조 온도 및 성형시간이 펠릿의 내구성에 미치는 영향을 알아보기 위하여 수행하였다. 수종별 내구성의 비교에서 낙엽송 펠릿의 내구성이 백합나무 펠릿보다 높았으며, 낙엽송 펠릿의 경우 18 mesh (1.00 mm) 이상 크기의 톱밥으로 제조한 펠릿이 8~18 mesh (1.00~2.38 mm)의 톱밥으로 제조한 펠릿보다 내구성이 높았다. 펠릿제조 온도를 높이고 펠릿 성형시간을 연장함에 따라 펠릿의 내구성은 증가하였으며, 톱밥의 함수율이 올라감에 따라 펠릿의 내구성은 향상되는 것으로 나타났다. 한편, 본 연구에서 제조된 낙엽송 및 백합나무 펠릿은 대조구로 사용된 산림조합 및 일도에서 제조한 목재 펠릿보다 내구성은 낮았으나, 대부분의 낙엽송 펠릿은 국립산림과학원에서 고시한 목재펠릿의 내구성 1등급 기준(97.5%)을 만족하였으며, 백합나무 펠릿은 3등급 기준(95%)을 모두 상회하였다. 전자현미경을 이용한 펠릿의 관찰에서 펠릿제조 온도를 높이고 펠릿 성형시간을 연장함에 따라 펠릿내에서 톱밥 간의 거리가 감소하고, 특히 $180^{\circ}C$의 온도에서 3분의 성형시간으로 제조한 펠릿의 경우 대조구 시편과 크게 차이가 없는 것을 육안으로 확인할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제51권1호
• /
• pp.23-37
• /
• 2023

One type of biomass that has promising potential for bio pellet production is spent coffee grounds (SCGs). However, previous studies have shown that SCGs in bio pellets cause a lot of smoke. Therefore, they need to be mixed with a material that has a higher calorific value to produce better quality pellets. One material that can be used is pine wood because it has a natural resin content that can increase the calorific value. The aim of this study was to examine the quality of bio pellets produced with SCGs and pine wood charcoal at different particle sizes. The charcoal was ground using either a hammer mill (HM) or a ball mill (BM). Pine wood charcoal was mixed with SCGs at ratios of SCGs to pine wood charcoal of 4:6 and 6:4 by weight, respectively, and the adhesive used a tapioca with a composition ratio 5% of the raw material. The bio pellets were produced using a manual pellet press. The quality of the bio pellets was assessed based on Indonesian National Standard (SNI) 8021-2014, and the physical observations include flame length, burning rate, and compressive strength. The average water content, ash content, and calorific value of the bio pellets were in accordance with SNI 8021-2014, but the density and ash content values were below the standard values. The BM variation of bio pellets had a higher compressive strength than the HM variation, and the 4:6 BM variation had the longest burning time compared with 4:6 HM.