• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.437-442
• /
• 2005

This paper deals with the measurement and analysis of radio characteristic of 424 MHz for using the automation of transmission and supply of electric power, ana automatic meter reading(AMR). Normally radio propagation characteristic is the base of system design, performance evaluation and choice of position of the base station in wireless communication. It is the most accurate way to design a base station through practical measurements, but it costs much time, money and engineers. So, we developed 424 MHz short range wave propagation model for AMR service.

• 대한전자공학회논문지TC
• /
• 제46권10호
• /
• pp.57-62
• /
• 2009

본 논문은 방사선 피폭량을 실시간으로 산출하기 위해 무선전력 전송용 13.56MHz의 안테나 설계를 위한 안테나 회로의 최적화 및 수치적 해석을 연구하였다. 리더기(Reader)에서 테크(Tag)로 무선으로 전력을 전송하기 위해서 안테나 주파수 대역 중 13.56MHz는 유도 전류를 이용한 루프 안테나에 많이 이용하고 있다. 본 논문은 전자유도 방식의 원리를 이용해 안테나 LC 공진을 위한 수치적 계산을 통해 L과 C 값을 산출하여 실제 측정치와의 값과 비교하였다. 또한 안테나 회로의 최적화 튜닝 및 안테나 포트의 매칭을 위해 공진(Resonance)용 캐패시터를 가변하여 스코프로 안테나 코일으 양단의 전압이 최고시점을 관측하여 공진점을 찾아 보았다. 이러한 실험은 무선으로 전력을 공급 받을 수 있는 무선전력 전송 시스템에 응용되어 매우 유용하게 활용될 것으로 기대된다.

• Journal of electromagnetic engineering and science
• /
• 제19권1호
• /
• pp.48-55
• /
• 2019

Unmanned aerial vehicles (UAVs) using communications, sensors, and navigation equipment will play a key role in future warfare. Currently, UAVs are monitored to prevent misfire and accidents, and the conventional method adopted uses wires for data transmission and power supply. The repeated connection and disconnection of cables increases maintenance time and harms the connector. For convenience and stability, a wireless power transfer system to power UAVs is needed. Unlike other wireless power transfer (WPT) applications, the size of the receiving coils must be small, so that the WPT systems can be embedded inside space-limited UAVs. The small size reduces the coupling coefficient and transfer efficiency between the transmitting and the receiving coils. In this study, we propose a toroidal-shaped coil for a WPT system for UAVs with high coupling coefficient with minimum space requirements. For validation, conventional coils and the proposed toroidal-shaped coil were used and their coupling coefficient and power transfer efficiency were compared using simulated and measured results. The simulated and measured results were strongly correlated, confirming that the proposed WPT system significantly improved efficiency with negligible change in the space requirement.

• 한국산학기술학회논문지
• /
• 제21권4호
• /
• pp.268-275
• /
• 2020

국내 산악 지역 자연공원에서는 자연 환경과 주변 조망을 보존하기 위해 전차선의 설치가 불가하다. 따라서 산악 트램은 무가선으로 운행되어야 한다. 이를 위해 본 연구에서는 차량의 추진 배터리에 전기를 공급할 수 있는 지상 집중식 급전장치를 개발하고 동작 및 기능 시험을 실시하여 성능을 검증하였다. 개발한 지상 집중식 급전장치는 검수고 또는 정거장의 한 지점에 고정 설치되어 있으며, 차량의 대차가 진입하여 정차하면 스프링 장력으로 암과 집전 슈를 올려 대차 하부에 있는 차량측 집전 바와 접촉하고, 전기를 흘려 배터리에 전력을 공급한다. 지상 집중식이므로 차량 지붕 위의 집전장치와 전차선이 필요 없게 되고, 산악트램은 무가선 상태로 운행을 할 수 있다. 정거장이나 검수고에서 움직이지 않고 정지한 상태에서 집전하므로, 이선이나 아크 발생이 없다. 집전 슈의 마모나 손상을 초래할 수 있는 가동 접촉면이 사라지게 되므로 집전장치 수명이 연장되는 장점이 있다. 시험 결과에 따르면, 절연저항은 기준치인 10㏁ 이상이었고, 전류 335A를 1시간 동안 일정하게 공급하여도 이상 발열이 없음을 확인하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(3)
• /
• pp.153-156
• /
• 2000

In this paper, we developed an outdoor augmented reality system which has remote real scenes acquisition ability. The real scenes acquisition system consists of Image acquisition system, tracking system, wireless data transceiver and power supply. The tracking system consists of Tans Vector and RT-20 which measures a position and attitude of the CCD camera that attached to the remote control helicopter. Wireless data transceiver system is utilized for data transmission of remote system that of attitude, position information, and real scenes data that acquired by the CCD camera. Maximum propelling power of remote control helicopter is 15Kg, so we used 7.2V li-ion cell as a power supply for system minimize. As the results of experiment, the developing system presented application possibility of remote information acquisition system such as construction simulation & estimation, broadcasting, tour guide.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.468-479
• /
• 2016

고압 전선 등에 장착된 시스템에 전원을 공급하기 위해서는 절연 이격 거리 이상의 거리에 무선으로 수십 Watt 급의 전력을 보낼 수 있는 시스템이 필요하다. 이러한 무선 전력 전송 시스템은 대개 코일의 크기가 10cm 이상의 대형이다. 본 연구에서는 이처럼 대형 코일을 Printed circuit board를 이용해 제작할 경우 발생하는 손실 발생원 들을 분석하고 그 중 가장 주요한 손실원인이 Dielectric loss 라는 것을 밝혔다. 또한 이 dielectric loss를 최소화 하기 위해서 PCB의 재질 선정 방법 및 Distributed tuning capacitor method를 제시해 $40cm{\times}40cm$ 크기의 4턴 및 5턴 코일의 설계 방법을 제시했고, 실험을 통해 Quality factor를 300 이상으로 만들 수 있음을 보였다.

• 한국전기전자재료학회논문지
• /
• 제29권12호
• /
• pp.769-775
• /
• 2016

Characteristics of a wireless sensor powered by the IDE (interdigitated electrode) embedded piezoelectric cantilever generator were analyzed in order to evaluate its potential for use in wireless sensor applications. The IDE embedded piezoelectric cantilever was designed and fabricated to have a self-resonance frequency of 126 Hz and acceleration of 1.57 G, respectively, for the mechanical resonance with a practical conveyor system in a thermal-power plant. It produced maximum output power of 2.81 mW under the resistive load of $160{\Omega}$ at 126 Hz. The wireless sensor module is electrically connected to a rectifier capacitor with capacity of 0.68 farad and 3.8 V for power supply by the piezoelectric cantilever generator. The unloaded capacitor could be charged as a rate of approximately $365{\mu}V/s$ while the capacitor exhibited that of 0.997 mV/min. during communication under low duty cycle of 0.2%. Therefore, it is considered that the fabricated IDE embedded piezoelectric cantilever generator can be used for wireless sensor applications.

• 한국기계가공학회지
• /
• 제19권8호
• /
• pp.73-80
• /
• 2020

The 3D printing of electronics has been a major application topics in additive manufacturing technology for a decade. In this paper, wireless power transfer (WPT) technology for 3D electronics is studied to supply electric power to its inner circuit. The principle of WPT is that electric power is induced at the recipient antenna coil under an alternating magnetic field. Importantly, the efficiency of WPT does rely on the design of the antenna coil shape. In 3D printed electronics, a flat antenna that can be placed on the printed plane within a layer of a 3D printed part is used, but provided a different antenna response compared to that of a conventional PCB antenna for NFC. This paper investigates the WPT response characteristics of a WPT antenna for 3D printed electronics associated with changes in its design elements. The effects of changing the antenna curvature and the gap between the wires were analyzed through experimental tests.

• Journal of KIEE
• /
• 제10권1호
• /
• pp.35-42
• /
• 2000

An equivalent load sharing control based on the frequency and voltage droop concept for parallel operation of two three-phase Uninterruptible Power Supply (UPS) systems with no control interconnection lines is presented in this paper. First of all, due to the use of active power and reactive power as control variables, the characteristics of output powers according to amplitude and phase differences between output voltages of two UPS systems are analyzed. Secondly, simulation results under different line impedance demonstrate the feasibility of the wireless parallel operation control. Finally, experiments are presented to verify the theoretical discussion with two three-phase 20kVA UPS systems employed TMS320C32, a kind of real time digital signal processor (DSP).

• International journal of advanced smart convergence
• /
• 제3권2호
• /
• pp.14-17
• /
• 2014

Precision agriculture relies on information technology, whose precondition is providing real-time and accurate information. It depends on various kinds of advanced sensors, such as environmental temperature and humidity, wind speed, light intensity, and other types of sensors. Currently, it is a hot topic how to collect accurate information, the main raw data for agricultural experts, monitored by these sensors timely. Most existing work in WSNs addresses their fundamental challenges, including power supply, limited memory, processing power and communication bandwidth and focuses entirely on their operating system and networking protocol design and implementation. However, it is not easy to find the self-localization capability of wireless sensor networks. Because of constraints on the cost and size of sensors, energy consumption, implementation environment and the deployment of sensors, most sensors do not know their locations. This paper provides maximum likelihood estimators for sensor location estimation when observations are time-of arrival (TOA) range measurement.