• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.2
• /
• pp.128-136
• /
• 2006

The present study examined the effects of micro leading-edge flaps on the vortex characteristic changes of a double-delta wing through pressure measurements of the wing upper surface and PIV measurements of the wing-leeward flow region. The experimental data were collected and analyzed while changing the deflection angle of the leading-edge flaps to investigate the feasibility of using micro leading-edge flaps as flow control devices. The test results revealed that the leading edge modification could greatly alter the vortex flow pattern and the wing surface pressure of the delta wing, which suggested that the leading-edge flaps could be used as an effective device for the control of delta-wing vortex flow.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.1
• /
• pp.55-65
• /
• 2017

Underwater torpedo has control fin with very low aspect ratio due to launching from limited size of cylindrical torpedo tube. If the aspect ratio of control fin of underwater vehicle is very low three-dimensional flow around control fin largely reduces control forces. In this study, the end plate was applied to reduce the three-dimensional flow effects of partially movable control fin of underwater vehicle. Through numerical simulations the flow field around control fin was examined with and without end plate for different flap angles. The pressure, vorticity, lift and torque on the control fin were analyzed and compared to experiments. The comparison have shown a reasonable agreement between numerical and experimental results and the effect of end plate on a low aspect ratio control fin. When the end plate was attached to the movable control fin, the lift increased and the actuator shaft torque did not significantly change. As this means less consumption of the actuator shaft torque compared to the control fin that has the same control force, the inner actuator capacity can be reduced and energy consumption can be saved. Considering this, it is expected to be effectively applied to the control fin design of underwater vehicles such as torpedoes.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.353-359
• /
• 2019

In this study, a aerodynamic loads prediction to design a deploying device of folded fin was introduced. In general, resultant flow conditions around the fin are used to obtain deploying moments and required energy. However, when it comes to the air vehicles launched from a mobile platform, more specific flow conditions can be provided. With the conditions, the design criteria can be calculated more realistically. In this study, therefore, aerodynamic moments induced by aerodynamic loads and energy required in deployment were calculated using wind-over-deck(WOD) velocity, combination of a platform velocity and a wind velocity. For the calculation, wind tunnel test was conducted on various angle of attack, side slip angles, and folding angles. It was found that the aerodynamic moments and the energy required in deployment using the non-uniform flow due to the velocity components were less than those using the uniform flow without the components.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.113-120
• /
• 2011

Fins are widely used for roll stabilization of passenger ferries and high performance naval ships, among others. The Coanda effect is noticeable when a jet stream is applied tangentially to a curved wing surface since the jet can augment the lift by increasing the circulation. The Coanda effect has been found useful in various fields of aerodynamics and speculated to have practical applicability in marine hydrodynamics where various control surfaces are used to control motions of ships and the other offshore structures. In the present study, numerical computations have been performed to find proper jet momentum coefficients $C_j$ and trailing edge shapes suitable for the application of the Coanda effect to a stabilizer fin. The results show that the lift coefficient of the modified Coanda fin at the zero angle of attack ${\alpha}$ identically coincides with that of the original fin at ${\alpha}\;=\;25^{\circ}$ when Coanda jet is supplied at the rate of $C_j$ = 0.1. It is also shown that a fixed type fin stabilizer utilizing the Coanda effect can be implemented without changing the fin angle to actively control the motions of ships and the other offshore structures.

• Journal of the Korean Society of Visualization
• /
• v.5 no.2
• /
• pp.20-25
• /
• 2007

The geometry of a commercial passenger airplane is realized based on a Boeing 747-400 model through the photographic scanning and reverse engineering. The each element consisting of the plane such as fuselage, wing, vertical fin, stabilizer and engines, is individually generated and then the whole body is assembled by the photomodeler. The maximum error in the realized airplane is about 1.4% comparing with the real one. The three-dimensional inviscid steady compressible governing equations are solved in the unstructured tetrahedron grid system, and in a finite volume method using STAR-CD when the airplane flies at the cruise condition. The pressure distribution on the surface and the wing-tip vortices are visualized, and in addition to the aerodynamics coefficients, lift and drag are estimated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.295-305
• /
• 2005

To improve the aerodynamic effciency of TR-E2, a new configuration so called TR-E2Sl was introduced. TR-2251 is composed of different wing airfoil section and T-tail shape compared with TR-E2. Wind tunnel test for TR-EBS1 had been performed by changing the incidence angles of wing and deflection angles of control surfaces such as elevator and rudder. Also the on/off effect of ventral fin attached underneath of AFT fuselage was tested. Test result showed that variations of wing incidence angle did not cause any severe differences in aerodynamic characteristics. Longitudinal and directional characteristics of TR-E2S1 show stable for the pitch and yaw motions. However, the lateral stability of TR-E2S1 is not stable for a certain control surface deflection.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.8
• /
• pp.975-983
• /
• 2011

A microfin on a heated surface and its effects of the heat transfer has been investigated. The thickness of the fin is about 8 micrometer to allow the flexible up-down motion of the fin. Two-way complete FSI (Fluid-Structure Interaction) method has been applied for the analysis. Firstly, the deformation of a microfin due to the pulsating flow is evaluated using structure analysis. The flow and temperature patterns are predicted by CFD (Computational Fluid Dynamics) method. At each time step, using the pressure force and temperature distribution from CFD, the deformation of the wing is evaluated by FEM. Also in order to estimate the resonance probability, the natural frequency of the wing structure is calculated by modal analysis. The proposed numerical procedure was validated through experiment using a single fin. Through this work, we show that the increase of 40% in heat transfer capacity using the microfin has been compared with that of flat plate case.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.53 no.1
• /
• pp.83-89
• /
• 2020

This study provides a detailed morphological description of larvae obtained from Urocampus nanus and Syngnathus schlegeli male brood fish over 20 days of culture in the laboratory. In both species, mating takes place when several males each spread their brood pouch like a wing to attract a female's attention. When the female begins to swim upward, the males follow her and receive her eggs in their brood pouches. Newborn larvae of U. nanus and S. schlegeli had already completed formation of dorsal and caudal fin rays, but not of pectoral fin rays. Pectoral fin rays were completely formed 15 days after release in S. schlegeli and 20 days after release in U. nanus. The ratio of caudal fin length to standard length increased until 8 days and decreased thereafter in S. schlegeli, while in U. nanus this ratio declined continuously after hatching. The larvae of the two species were very similar in external morphology, but well distinguished by the number of dorsal fin rays (15-16 in U. nanus vs. 39-43 in S. schlegeli), the presence of a membrane under the tail (absent in U. nanus vs. present in S. schlegeli), and the presence of melanophores in the dorsal fin (present in U. nanus vs. absent in S. schlegeli). Based on this study, U. nanus appears to be evolutionally more similar to pipefish than to seahorse.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.5
• /
• pp.625-636
• /
• 2019

Recently, research on projectiles with wings for precision guidance is actively underway. In this study, we analyzed how the tail fins attached to the projectile affect the base drag. Aerodynamic analysis was performed with RANS(Reynolds Averaged Navier-Stokes) equations using FLUENT, a commercial CFD(Computational Fluid Dynamics) code. Through the aerodynamic analysis, the base drag characteristics of the projectile by parameters (number, length, thickness, position, shape of tail fin) were investigated. The results of this study are expected to be applicable to aerodynamic design of tail fins mounted on projectiles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.579-585
• /
• 2019

Increasing the detection probability of underwater targets necessitates securing the towing stability of the active towed SONAR. In this paper, to confirm the effects of tail wing fin on towing attitude and towing stability, two scale model experiments and one sea trials were conducted and the results were analyzed. The scale model tests measured the towing behavior of each of the tail fin shapes according to towing speed in a towing tank. The shape of the tail fin used in the scale model test was tested with an I-type tail fine and four Y-type tail fins, totaling five tail fins of the two kinds. The first scale model test confirmed that the Y-type tail fin was superior to the I-type tail fin in towing attitude and towing stability. The second scale model test confirmed the characteristics of the vertical tail fin height increase and the lower horizontal tail fin inclination angle application shape based on the Y-type tail fin. The shape of the application of the lower horizontal tail fin inclination angle showed the best performance. In order to verify the results of the scale model test, a full size model was constructed, sea trials were performed, and the towing attitude was measured. The results were similar to those of the scale model test.