• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.889-895
• /
• 2011

PMLSM is structurally simple and it have a lot of merits such high speed, high thrust force etc., but cogging force by slot-teeth structure of armature and cogging force by outlet edge effect occurs. This is the cause of thrust force ripple and generate the noise and vibration. Therefore, in this paper we proposed installation of an auxiliary pole to mover of the PMLSM in order to decrease cogging force by the outlet edge which came necessarily into being discontinuous arrangement of the armature. Also, outlet edge cogging force designed a form of the auxiliary pole which the minimum became, and we compared a outlet edge cogging force characteristic along a winding method of an armature as we used 2-D of finite element analysis.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.352-356
• /
• 2013

Recently, the stationary discontinuous armature, Permanent Magnet Linear Synchronous Motor (PM-LSM), was suggested as a driving source for long-distance transportation system. However, as these motors arrange armatures discontinuously, an edge occurs thereby leading to a cogging force. This works as a factor that hinders the acceleration and deceleration that takes place when movers enter into and eject from armatures. Therefore, in this study, the installation of auxiliary teeth on the edge of the armature of PM-LSM is suggested in order to reduce the cogging force caused by the edge when the armature is placed in a discontinuous arrangement. Auxiliary teeth are optimally designed by a 2-D numerical analysis using the finite element method was performed to generate the optimum design of the auxiliary teeth. The validity of the study was confirmed through the comparison of the cogging force induced at the edge in respect to the design parameter using the basic model.

• Journal of Digital Convergence
• /
• v.11 no.1
• /
• pp.13-25
• /
• 2013

After studying FSMA 24, We found that the insolvency rule of financial institutions in FSMA consists of eight provisions: 1) voluntary arrangement, 2) administration order, 3) receiverships, 4) voluntary winding up, 5) winding up by the court, 6) bankruptcy, 7) provisions against debt avoidance, and 8) supplemental provisions in insurance cases. Insolvency provisions in FSMA explain powers and accountabilities of FSA in relation to these insolvency proceedings. Although there are some differences in proceedings, provisions entitle FSA the same status as creditors to petition the court, with a right to participate in related meetings and to be notified of any matters involving insolvency proceedings. The differences and implications between U.K.'s FSMA and Korean regulations are related to the insolvency rule of financial institutions. First, in FSMA, FSA has a comprehensive power to manage insolvency proceedings of financial institutions in a centralized way. However, Korean regulations have special laws to regulate insolvency in a decentralized way. The offices executing those laws are the Financial Services Committee, the Financial Supervisory Service, and the Financial Deposit Insurance Corporation. This characteristic results from an accelerated legislation procedures related to financial reform in 1997 Korean financial crisis. Second, FSA contains special provisions on continuation of contracts of long-term insurance considering the characteristics of insurance industry related to insolvency of financial institution. However, Korean insolvency rules applied to financial institutions do not consider industrial differences and the characteristics of financial contracts, so need to be supplemented in the future.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.12
• /
• pp.700-708
• /
• 2004

Flux-reversal machine (FRM) is a new doubly-salient stator-permanent magnet (PM) machine with flux linkage reversal in the stator concentrated windings. It can operate in both motoring and generating modes. In this paper, a novel design technique to improve the performance of FRM is proposed. Proposed techniques have a new stator winding and a magnet arrangement method. The stator and rotor shape with a concave type and a flux barrier are also proposed. According to the experimental results, it is shown that the proposed FRM have an improved performance.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.892-893
• /
• 2015

This paper deals with a characteristic that varies the number of magnetic pole in permanent magnet (PM) motor in order to reduce energy consumption. The pole changing memory motor (PCMM) can change the number of magnetic poles and produce two types of torque. When the motor operates with eight poles, it produces a magnetic torque at low rotational speeds. When the motor changes to four poles, it produces both magnetic torque and reluctance torque at high speeds. The paper explain the principle and basic characteristics of the motor by using a finite element method magnetic-field analysis, which consists of a PM magnetized by a pulse d-axis current of the armature winding. The results of our experiment show that the proposed motor reduces core loss by 10% and 55% under no-load and load conditions, and doubles the speed range of the motor.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.238-240
• /
• 1998

This paper deals with the design of a disk-type motor excited by permanent magnets. The main flux is oriented in the axial direction, yielding a pan cake type arrangement. the outer diameter is about 65mm, inner diameter is about 30mm, the axial length about 15mm. For reduce axial length and high efficiency, motor winding have been etched copper plate. After the introduction, the motor design is explained and characteristic of axial flux permanent magnet motor have been investigated. A prototype AFPM motor have been assembled and driving power supply are made. A characteristic of magnetical and electrical and characteristic are investigated.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1122-1132
• /
• 2019

In this paper, aiming at high-voltage applications, transformer windings schemes of multiple-output two-transistor flyback converters are investigated, which are mainly based on the stray capacitances effect. First, based on a transformer model including equivalent stray capacitors, the operational principle of the converter is presented, and the main influence of its stay capacitors is determined. Second, the windings structures of the transformer are analyzed and designed based on the stray capacitances effect. Third, the windings arrangements of the transformer are analyzed and designed through a coupling analysis of the secondary windings and a stray capacitance analysis between the primary and secondary windings. Finally, the analysis and design conclusions are verified by experimental results obtained from a 60W laboratory prototype of a multiple-output two-transistor flyback converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.157-164
• /
• 2022

This study proposes an enhanced quadruple-Active-Bridge (QAB) converter that can solve power coupling problems. By adopting a multiple winding transformer, the equivalent circuit of a conventional QAB converter has power couplings between arbitrary output ports. This coupling is an unintended power relationship that complicates the regulation of output voltage of the multiple ports. The proposed converter can carry out power decoupling by changing the arrangement of the coupling inductor. Power transfer equations for the proposed converter and its operating principles are analyzed in detail. The power coupling caused by the transformer's leakage inductance is verified by using a proposed coupling factor that presents the relationship between inductance ratio and coupling power. In addition, the decoupling power control performance of the proposed converter is verified by simulation and a 3 kW prototype converter.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.1067-1072
• /
• 2012

Recently, linear motors have been widely researched and have been increasingly used in various industrial applications. Especially, permanent magnet linear synchronous motors(PMLSMs) have been getting the spotlight in the transportation system. A PMLSM is structurally simple and has a lot of merits such as high speed, high thrust force, etc. However, in case of a long stator system which arranges armature to the full length of transportation lines, a PMLSM has some disadvantages such as the material cost increase and long manufacturing time. Hence, in order to overcome these problems, the PMLSM with stationary discontinuous armature structure and concentrated windings was proposed. However, this method occurs undesirable cogging force by outlet edge effect. The cogging force causes thrust force ripples and generates noise and vibration. Therefore, in this paper, we proposed installation method of auxiliary pole PMLSM with concentrated winding applying bifurcating in order to reduce cogging force by the outlet edge when the armature is placed in a discontinuous arrangement. Also, we have examined characteristics of outlet edge cogging force using 2-D finite element analysis(FEA).

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.86-89
• /
• 2002

In this paper, the design of a IMVA single-phase high temperature superconducting(HTS) power transformer with BSCCO-2223 HTS tapes is presented. The rated voltages of each sides of the transformer are 22.9 ㎸ and 6.6 ㎸, respectively The winding of 1MVA HTS transformer is consisted of double pancake type HTS windings, which have advantages of insulation and distribution of high voltage, and are cooled by subcooled liquid nitrogen of 65K. Four HTS tapes were wound in parallel for the windings of low voltage side and the four parallel conductors are transposed. The design of 1MVA HTS transformer, a shell type core made of laminated silicon steel plate is chosen, and the core is separated with the windings by a cryostat with a room temperature bore. The cryostat made of non-magnetic and non-conducting material and a liquid nitrogen sub-cooling system is designed in order to maintain the coolant's temperature of 65K. For electromagnetic analysis of 1MVA HTS transformer, a finite element method of an axis of symmetry is used. The maximum perpendicular component of magnetic flux density of pancake windings is about 0.15T. And through analyzing the magnetic field distribution, an optimal winding arrangement of 1MVA HTS transformer is obtained.