• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.350-355
• /
• 2003

This paper presents results of vibration analysis of a end-winding of large generator for fossil power plant. A finite element analysis using a commercial S/W is performed to calculate alternating electromagnetic forces, mainly of 120㎐ in 60㎐ machines, acting on the end-winding, and then to calculate forced response of the end-winding under electromagnetic forces. Also, this paper presents analytical and experimental modal analysis results of generator end-winding to validate FE model. We calculated forced response of end-winding on 120㎐, double rotating frequency. These results will be used to evaluate structural reliability of end-winding and applied to update model.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.478-482
• /
• 2015

This paper describes the torque calculation of Flux Switching Motor using Winding Function Theory. First of all, the optimized new Flux Switching Motor was proposed to minimize the torque ripple. The simulation results by the Winding Function Theory were compared with those from Finite Element Analysis. The revised Flux Switching Motor and experimental setup were manufactured. The simulation result by the Winding Function Theory was compared with that of the experiment. The comparison validated the analysis method of the Flux Switching Motor by Winding Function Theory.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.826-831
• /
• 2001

Electromagnetic forces generate vibrations in the end-winding of large generators. A finite element analysis using a commercial S/W is performed to calculate electromagnetic force of end-winding in two pole generator for 500 MW fossil power plant. Also, this paper presents analytical and experimental modal analysis results of generator end- winding. Using validated FE model, 3D electromagnetic model which computes the forces on the end-winding is coupled with a 3D mechanical model which calculates the dynamic displacement and stress under electromagnetic forces. These results will be used to evaluate reliability of end-winding and applied to update model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.54-62
• /
• 2014

This study deals with the design and characteristics analysis on a linear synchronous motor (LSM) with a long stator and phase concentrated winding (PCW) to apply for a propulsion system such as a roller coaster for leisure facilities. First of all, the required propulsion force of LSM is computed and its design with double sided permanent magnets (PMs) and a phase concentrated winding is processed. The phase concentrated winding is composed of a module with each A, B, and C phase unlike an conventional concentrated winding (CW). It has an advantage of the installation and manufacture, compared to the conventional concentrated winding in the propulsion system for leisure facilities that have a long acceleration area and stator configuration placed on rail continuously. Thus, the design for the propulsion system and characteristics comparison between the phase concentrated winding and concentrated winding are carried out in this paper. Also, the analysis on dynamic characteristics is conducted to confirm the performance at operation.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.54 no.1
• /
• pp.15-19
• /
• 2005

This paper analyzed the power loss characteristics according to winding thickness and winding method of high frequency transformer. Power loss was analyzed by PExprt using FEM tool. The ferrite core model for analysis be used the EE10 type of TDK cop.. Transformer model objected flyback transformer type applied to flyback converter/inverter. Therefore, analysis results of loss were obtained from inner parameters of DC, AC resistance, leakage inductance, copper loss, core loss, and temperature etc.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.59-66
• /
• 2011

This work treat the modeling and simulation of non-linear dynamic behavior of a web winding process during traction. We designate by a winding process any system applying the cycles of unwinding, transport, treatment, and winding to various flat products. This system knows several constraints, such as the thermal effects caused by the frictions, and the mechanical effects provoked by metal elongation, that generates dysfunctions due to the influence of the process conditions. Several controllers are considered, including Proportional-integral (PI) and Backstepping control. This paper presents the study of Backstepping controls strategy of the winding system. Our winding system is simulated in MATLAB SIMULINK environment, the results obtained illustrate the efficiency of the proposed control with no overshoot, and the rising time is improved with good disturbances rejections comparing with the classical control law.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.463-474
• /
• 2019

This paper presents the effect of winding configuration on the kVA rating of a wye-connected autotransformer applied to a 12-pulse rectifier. To describe the winding configuration of the wye-connected autotransformer, position and proportional parameters are defined and their quantitative relation is calculated. The voltages across and currents through the windings are measured under different winding connections. Consequently, a relation between the kVA rating and position parameter is established in accordance with the analysis, and the optimal winding configuration is obtained on the basis of this relation. A wye-connected autotransformer with the least equivalent kVA rating and simplest winding configuration is designed and applied to the 12-pulse rectifier. Simulations and experiments are conducted to validate the theoretical analysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.776-780
• /
• 2011

This paper is concerned with winding design in capacitor-run single phase motor. Winding design in single phase induction motor is more complicated than that in three phase induction motor, because of using concentric winding in the single phase. Various winding designs are possible, and accordingly layout of the slot is calculated by formula. And then accurate design of winding is available. Using the design process in this paper, we can get the base model with slot layout and turns of windings of 1.12 kW single phase induction motor, and it is verified by finite element analysis. In this paper, winding design and winding layout of single-phase induction motor using concentric winding are suggested.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.5
• /
• pp.730-735
• /
• 2012

This paper presents a method to design the waveform of a back electromotive force (back EMF) of an axial flux permanent magnet (AFPM) motor using printed circuit board (PCB) windings. When the magnetization distribution of permanent magnet (PM) is given, the magnetic field in the air gap region is calculated by the quasi three dimensional (3D) space harmonic analysis (SHA) method. Once the flux density distribution in the winding region is determined, the required shape of the back EMF can be obtained by adjusting the winding distribution. This can be done by modifying the distance between patterns of PCB to control the harmonics in the winding distribution. The proposed method is verified by finite element analysis (FEA) results and it shows the usefulness of the method in eliminating a specific harmonic component in the back EMF waveform of a motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.7
• /
• pp.26-31
• /
• 2011

In this paper, torque characteristics analysis of Synchronous Reluctance Motor with the cylindrical rotor type by winding function theory(WFT) is described. The stator is same as one of the induction motor. From the d-axis, q-axis flux density distribution, to calculate self and mutual inductances needed to calculate the torque of the machine by using winding function theory the new equivalent geometry of rotor was proposed. D-axis, q-axis flux densities, self inductance and torque characteristics were obtained. From the comparison with results of finite element analysis the proposed method was verified.