• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권6호
• /
• pp.286-292
• /
• 2005

Terahertz wave is a kind of electromagnetic radiation whose frequency lies in 0.1THz $\~$10THz range. In this paper, generation and detection characteristics of terahertz (THz) radiation by photoconductive antenna (PCA) method has been described. Using modern integrated circuit techniques, micron-sized dipole antenna has been fabricated on a low-temperature grown GaAs (LT-GaAs) wafer. A mode-locked Ti:Sapphire femtosecond laser beam is guided and focused onto photoconductive antennas (emitter and detector) to generate and measure THz pulses. Ultra-wide band THz radiation with frequencies between 0.1 THz and 3 THz was observed. Terahertz field amplitude variation with antenna bias voltage, pump laser power, pump laser wavelength and probe laser power was investigated. As a primary application example. a live clover leaf was imaged with the terahertz radiation.

• 한국레이저가공학회지
• /
• 제11권2호
• /
• pp.15-19
• /
• 2008

Electron beam (EB) weldability of pure grade Nb sheet was studied. One of Nb sheets was as-annealed and the other was cold rolled. Microstructures, Vickers hardness, and transverse weld tensile test were carried out for the base metal, the heat affected zone (HAZ) and weld metal. In the case of the EB welds made using the annealed Nb sheeet, fine equiaxed grains and coarse grains were dominant at the base metal and the HAZ, respectively, and columnar grains were observed at the weld metal. For the EB welds made using the cold rolled Nb sheet, elongated grains in the rolling direction at the base metal, and the microstructures of the weld metal and the HAZ are similar to those of the EB welds made using the annealed Nb sheet, respectively. For both annealed and cold rolled Nb sheet, the width of the HAZs are unusually wide in spite of using high density heat source, i.e. electron beam, and the grain sizes of both HAZs are similar. When tensile test was carried out using the transverse weld specimens, the failure occurred at the HAZ for both EB welds made using Nb sheets annealed and cold rolled, respectively and the tensile strengths of both specimens were 161MPa. Vickers hardness of EB welds made using annealed Nb was 56-57 Hv at both base metal and weld metal, 52-53 Hv at the HAZ. On the other hand, Vickers hardness of EB welds made using cold rolled Nb was 97-99 Hv at the base metal, but the hardness values of weld metal were similar to those obtained at the weld metal of annealed Nb.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.981-983
• /
• 1998

In this paper, we present theoretical designs for a beam steering phased array antenna that uses a true time delay optical feeder. A variable true time delay is achieved by employing one tunable laser source and high dispersion fibers with different length. The wavelength tunable optical carrier propagation in a high-dipersion fiber realizes a true time delay, with the steering direction set by a single voltage controlling the wavelength. Beamsteering of a phased array antenna is obtained by controlling the tunable laser source. An employment of a high dispersion fiber response shows wide-band operation of beem steering antenna system.

• 대한인간공학회지
• /
• 제20권3호
• /
• pp.77-88
• /
• 2001

A three dimensional body scanner for anthropomentric measurement has been developed. In this study, the slit laser beam projection method followed by digital image processing was used to provide accurate spatial data with the typical optical triangulation method to overcome the many difficulties in traditional in accurate and time-consuming tactic measurement method using rulers and gauges. Compared with other commercialized scanners. this system can obtain a relatively wide range of data at a much lower cost by the specially designed scanning process such as the simultaneous acquisition of vertical and horizontal body cross-section profiles.

• ETRI Journal
• /
• 제36권2호
• /
• pp.232-241
• /
• 2014

A holographic display system with a 22-inch LCD panel is developed to provide a wide viewing angle and large holographic 3D image. It is realized by steering a narrow viewing window resulting from a very large pixel pitch compared to the wave length of the laser light. Point light sources and a lens array make it possible to arbitrarily control the position of the viewing window for a moving observer. The holographic display provides both eyes of the observer with a holographic 3D image using two vertically placed LCD panels and a beam splitter to support the holographic stereogram.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.477-478
• /
• 2006

Characteristics of InAs/GaAs quantum dot (QD) ridge laser diodes (LDs) are investigated for high-power $1.3\;{\mu}m$ applications. For QD ridge LDs with a $5-{\mu}m$-wide stripe and a 1-mm-long cavity, the emission wavelength of 1284.1 nm, the single-uncoated-facet CW output power as high as 90 mW, the external efficiency of 0.31 W/A and the threshold current density of $800\;mA/cm^2$ are obtained. The linewidth enhancement factor ($\alpha$-factor) is successfully measured to be between 0.4 and 0.6, which are about four times as small values with respect to conventional quantum well structure. It is possible that this result significantly reduce the filamentation of far-field profiles resulting in better beam quality for high power operation.

• 한국광학회지
• /
• 제19권3호
• /
• pp.182-186
• /
• 2008

프리즘 분광기는 굴절률 측정을 위한 표준 장치로, 대학교 실험실에서 사용되는 전형적인 실험 기구이지만, 정렬할 때 많은 주의가 요구되고 장치의 견고함에 비해 측정된 굴절률의 정확도는 떨어진다. 이러한 단점을 보완한 최대 최소 편향법은 회전 플랫폼과 길이 측정용 테이프로 저렴하게 장치가 구성되고 넓은 스크린을 활용하여 비교적 정확하게 굴절률을 측정할 수 있다. 본 연구에서는 한변이 26 mm인 속이 빈 등변 프리즘을 제작하여 글리세린($C_3H_5(OH)_2$), 사염화탄소($CCl_4$), 아닐린($C_6H_4NH_2$), 이황화탄소($CS_2$), 크실렌($C_6H_4(CH_3)_2$) 등의 액체를 채워, He-Ne 레이저의 파장 632.8 nm와 $YVO_4$ 레이저의 파장 532 nm에 대해 프리즘 분광기와 최대 최소법으로 이들 액체의 굴절률을 측정하였다. 측정결과 최대 최소법으로 얻어진 데이터가 프리즘분광기에 의해 얻어진 데이터보다 더 정확하고 정밀함을 확인하였다.

• 비파괴검사학회지
• /
• 제26권2호
• /
• pp.84-89
• /
• 2006

레이저 초음파 검사 장치는 레이저빔을 이용하여 초음파 신호를 발생시키고 측정하는 비접촉식 결함 검사 장치이다. 이 장치는 펄스 레이저빔을 이용하여 광대역 주파수 범위를 갖는 초음파 신호를 발생시키고 작은 점으로 집속된 측정용 레이저빔을 이용하여 초음파 신호를 측정하므로 우수한 측정 분해능을 제공한다. 본 논문에서는 레이저 초음파의 표면파를 이용하여 표면 결함의 깊이를 측정하는 기법에 대한 연구를 수행하였다. 표면 결함은 깊이가 깊어질수록 차단 주파수 값이 작아지는 저주파 통과 필터 역할을 한다. 그리고 결함을 통과한 초음파 신호의 중심 주파수 값은 결함의 깊이에 따라 반비례적으로 작아진다. 본 논문에서는 표면 결함의 정규화 된 전달함수를 구한 다음 주파수 감쇠 성분을 이용하여 표면 결함의 깊이 정보를 추출하였고 표면 결함을 통과한 레이저 초음파 신호의 중심 주파수 값을 이용하여 결함의 릴이 정보를 추출하였다. 제안된 표면 결함 깊이 측정 방법은 초음파의 진폭 변화에 의한 결함 깊이 측정법보다 더욱 정밀한 정보를 제공하였다.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.68-73
• /
• 2009

Recently, as titanium and titanium alloys are being increasingly used in wide areas, there are on-going researches to obtain high quality weld zone. In particular, growing interest is being drawn to laser welding, which involves low heat input and large aspect ratio in various welding processes and can facilitate shield in atmospheric condition compared with electron beam welding. The first report covered the analysis of embrittlement by the bead color of weld zone through quantitative analysis of oxygen and nitrogen and measurement of hardness as basic experiment to apply laser welding to titanium. Results indicated that the element that affect embrittlement the most was nitrogen, and as embrittlement and oxygenation go on, bead color changed to silver, gold, brown, blue and gray. This study performed butt welding of pure titanium and STS304 by using 1kW CW Nd:YAG laser, and to find out basic physical properties, evaluated welding performance by laser output, welding speed, root gap and misalignment etc, and examined mechanical properties through tensile stress and Erichsen test. The reason particles of pure titanium welded metal and HAZ are greater than STS304 is because they are pure metal and do not include many impure elements that work as nuclei in case of resolidification, thus becoming coarse columnar crystals eventually. In addition, the reason STS304 requires more energy during welding than pure titanium is because the particle size of base metal is smaller.

• Journal of electromagnetic engineering and science
• /
• 제10권1호
• /
• pp.18-24
• /
• 2010

A Ka-band microstrip array antenna for wide-range detection of moving targets is analyzed through a photonicassisted reactive-near-field characterization technique. The antenna array employs a 3-dB-tapered feed network to suppress the sidelobe level while retaining a wide azimuth beamwidth for a wide detection range. The relative nearelectric field patterns of the array and its 3-dB-tapered feed lines have been measured using an electro-optic fieldmapping technique for minimally invasive millimeter-wave sensing. A number of typical limitations on the technique, involving bandwidth, low signal-modulation depth, and high laser-induced noise in high-frequency applications, have been overcome by suppressing the carrier portion of the optical interrogation beam.