• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.479-486
• /
• 2019

The fully digital active array radar uses a wide beam for effective mission performance within a limited time. This paper presents a convex optimization algorithm that adjusts only the phase of an array element. First, the algorithm applies a semidefinite relaxation technique to relax the constraint and convert it to a convex set. Then, the constraint is set so that the amplitude is fixed to some extent and the phase is variable. Finally, the optimization is performed to minimize the sum of the eigenvalues obtained through eigenvalue decomposition. Compared to the application results of the existing genetic algorithm, the proposed algorithm is more effective in wide beam design for a fully digital active array radar.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.279-287
• /
• 2002

In this paper, a symmetric microwave lens to steer wide angle and to operate at broad band frequency range for a linear phased array transmitter was designed. To get accurate beam steering performance far a linear phased array transmitter, uniform amplitude transmission characteristics of microwave lens was focused. The measured result for the insertion loss deviation between Input and output ports of microstrip lens with 8 beam ports and 8 array ports was $\pm$3.1 ㏈ over 6~18 ㎓ band, which was very uniform characteristics. Using 8 elements linear array antenna, it was confirmed the radiation beam could be steered over $\pm$60$^{\circ}$ in azimuth. And the measured lens performance data and multi-beam steering pattern were presented.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.12
• /
• pp.1632-1638
• /
• 2020

In this paper, we investigate a multi-beam satellite communication system where multiple terminals transmit information signals to the gateway via a satellite. The satellite is equipped with phased array antennas to form multiple spot beams of which bandwidths are not identically allocated. We formulate an optimization problem to maximize fairness of beam bandwidth allocation. In order to solve the problem, we propose two heuristic algorithms; iterative beam bandwidth allocation (IBBA) and request ratio-based beam bandwidth allocation (RRBBA) algorithms. The IBBA algorithm iteratively equalizes the ratio of allocated bandwidth of each beam to their resource request while the RRBBA algorithm allocates beam bandwidth calculated from the ratio. Simulation results show that the IBBA algorithm has close fairness performance to the optimum while the RRBBA algorithm has less performance than the IBBA algorithm at the price of reduced computational complexity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.2
• /
• pp.46-55
• /
• 2002

The key component to accomplish the WDM all optical network is an Arrayed Waveguide Grating(AWG) wavelength filter Numerical analysis is necessary for design and analysis of optical components like AWG wavelength filter. Beam Propagation Method(BPM) is the most widely-used method. In this paper, we analyze the difference between the paraxial BPM and the WA-BPM when they are applied to the analysis of InP/InGaAsP/InP AWG wavelength filter. The paraxial BPM is based on paraxial approximation, and the WA-BPM is based on the low order Pade approximant. The side lobe level(SLL) and insertion loss calculated from both methods are compared. The high order Pade approximant will to used to more accurate design and analysis of AWG.

• Imaging Science in Dentistry
• /
• v.48 no.3
• /
• pp.191-199
• /
• 2018

Purpose: This study classified alveolar arch forms and evaluated differences in alveolar bone thickness among arch forms in the anterior esthetic region using cone-beam computed tomography (CBCT) images. Materials and Methods: Axial views of 113 CBCT images were assessed at the level of 3 mm below the cementoenamel junction (CEJ) of the right and left canines. The root center points of teeth in the anterior esthetic region were used as reference points. Arch forms were classified according to their transverse dimensions and the intercanine width-to-depth ratio. The buccolingual alveolar bone thickness of each tooth was measured at 3 mm below the CEJ and at the mid-root level. Differences in the mean thicknesses among arch forms were analyzed. Results: Anterior maxillary arches could be classified as long narrow, short medium, long medium, and long wide arches. Significant differences in buccolingual alveolar bone thickness among the arch groups were found at both levels. The long wide arches presented the greatest bone thickness, followed by the long medium arches, while the long narrow and short medium arches were the thinnest. Conclusion: Arch forms were classified as long narrow, short medium, long medium, and long wide. The buccolingual alveolar bone thickness exhibited significant differences among the arch forms.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.417-423
• /
• 2004

In order to obtain wide-beam characteristics and variable resonant frequency of a ultrasonic transducer for the array source, an electrode of transverse mode piezoelectric vibrator is divided, and an electronic inductance is connected to the divided electrodes. The electronic inductance is made by GIC (General Impedance Converter) circuit. Because the GIC circuit is made of OP-Amps and other passive elements, the value of the inductance can be selected easily. As the results, the electronic inductance is variable in the range from 0.2 mH to 1.2 mH. Using the inductance, the resonance frequency of the transducer can be changed in the range from 73 kHz to 86 kHz. In the directivity of the transducer, it is confirmed that the beam width of the transducer is wider than $80^{\circ}$ at -3 dB in water.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.130-138
• /
• 2023

In this study, experimental and analytical studies were conducted on the structural performance of permanent steel formed wide beams in construction stage. Four specimens were fabricated with different rib spacings of the side steel formwork and fixing plate depths, and experimental tests were performed to investigate the effects of variables on the structural performance. Also, an finite element analysis model of the steel permanent formwork wide beam was proposed based on the test results. Using the proposed model, parametric studies were performed with variables including rib spacing of the bottom and side steel formwork, spacing, depth, and thickness of the fixing plate to derive optimized details. Furthermore, an artificial neural network model was developed to easily estimate the deformation of the steel permanent formwork wide beam with various details.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.912-918
• /
• 2001

This paper presents a performance analysis of experimental observations of a uplink smart antenna system operating in a wide-band CDMA environment designed for a WLL (Wireless Local Loop) system. The numerical results shown in this paper have been obtained from practical experiments using commercially developed mobile terminals. The beam pattern provided by the weight vector and the resultant BER (Bit Error Rate) are observed in both indoor and outdoor signal environments. From the experimental observations, it is concluded that the proposed smart antenna system provides significant improvements in receiving both indoor and outdoor signal environments.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.7-12
• /
• 2016

This paper proposes a metal contact RF MEMS switch which utilizes a see-saw mechanism to acquire a switching action. The switch was built on a quartz substrate and involves vertical deflection of the beam under an applied actuation voltage of 5.46 volts over a signal line. The see-saw mechanism relieves much of the operation voltage required to actuate the switch. The switch has a stiff beam eliminating any stray mechanical forces. The switch has an excellent isolation of −90.9 dB (compared to − 58 dB in conventional designs ), the insertion of −0.2 dB, and a wide bandwidth of 88 GHz (compared to 40 GHz in conventional design ) making the switch suitable for wide band applications.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.1
• /
• pp.107-113
• /
• 1993

Sidescan sonar uses the fan type beam which has horizontally narrow and vertically somewhat wide beam pattern. To construct such a beam we will use an array of transducers. In case of using single transducer it must have a high frequency to have the fan type beam, but in case of using an array it must have to be high frequency. We are planning to use 30 kHz transducers for our sidescan sonar under development. This paper shows ways of designing a narrow beam for the sidescan sonar system by illustrating various shapes of the beam patterns.