• Journal of Magnetics
• /
• 제13권2호
• /
• pp.70-75
• /
• 2008

In this study, a MOKE (Magneto-optical Kerr effect) measurement method for magnetic nanostructures is proposed. Theoretically, the MOKE signal enhancement can be predicted and confirmed when an anti-reflection coated substrate is used. Since MOKE is a ratio of reflectivity and the difference between the reflectivities for two magnetic states, when the reflectivity of the substrate part is reduced by employing an anti-reflection coated substrate, MOKE signal enhancement can be achieved. The enhancement is confirmed by simple numerical MOKE calculations. When the reflectivity of an anti-reflection coated substrate is 0.7%, the calculated MOKE signal is about 79% of its bulk values for the 100-nm wide Fe nanowire with a 1500-nm radius laser beam. It was found that, for various numerical calculations, a larger MOKE signal is obtained relative to a smaller substrate reflectivity.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.253-258
• /
• 2000

Recently, the area of design optimization, especially structural optimization, has been and to be a continuous active area of research. And the design optimizations of port facilities have been achieved by many other civil engineers. But the design optimization of port facilities were limited to the design optimization of the breasting dolphin. This paper invested the design optimization of mooring pier and the foundations of mooring pier was suggested considering the convenience of repair and reinforcement work. The mooring pier devised with prestressed precast concrete panel and rigid frame welded wide flange beam to steel pipe pile. To accomplish the design optimization of mooring pier, the Augmented Lagrangian Multiplier Method(ALM) of ADS(Garret N. Vanderplaats) optimization routine, BFGS method as optimizer and Golden Section Method as one dimensional search were utilized. As a result, thirty percent of material cost for construction was reduced by design optimization. The tensile stress of concrete panel and bottom flage was critical constraints under service load. So, using high strength concrete and steel will be economical. And lots of initial values must be invested to accomplish the design optimization in design procedures.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.162.6-162
• /
• 2001

Confocal scanning microscopy (CSM) is an important instrument in a wide variety of imaging applications because of its ability to provide three-dimensional images of thick, volume specimens. The mechanism for two-dimensional beam scanning and optical sectioning has an important roe in CSM as the three-dimensional profiler. This optical sectioning property arises from the use of a point detector, which serves to attenuate the signals from out-of-focus. The intensity profile for the open loop scanning should be matched with its response for the standard. The non-linearity can be minimized with the optical sectioning or the optical probe of the closed loop control. This paper shows the mathematical expression of the light such as the extinction curve in the optical fields of system using AO deflector, the axial/lateral response experimentally when the error sources change, and the methods of optical sectioning. Thorough design of optical sectioner is crucial to the success of CSM in the field ...

• 한국공작기계학회논문집
• /
• 제11권1호
• /
• pp.52-60
• /
• 2002

The purpose of this research is to study the vibration and acoustic pressure radiation from a thin isotropic flat plate stiffened by a rectangular array of beams, and excited by a time harmonic point force. These constructions on aircraft and ship structures are often subjected to fiequency dependent pressure fluctuations and forces. Forces from the these excitations induce structural vibrations in a wide range of fiequencies, which may cause such things as acoustic fatigue and internal cabin noise in the aircraft. It is thus important that the response characteristics and vibration modes of such periodic structures be horn. From this theoretical model, the sound pressure levels(SPL) in a semi-infinite fluid(water) bounded by the plate with the variation in the locations of an external time harmonic point farce on the plate can be calculated efficiently using three numerical tools such as the Gauss-jordan method the LU decomposition method md the IMSL numerical package.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.568-574
• /
• 2004

On-line phase tracking of an extrinsic Fabry-Perot interferometer (EFPI) and experimental vibration control of a composite beam with a sensing-patch are investigated. We propose a sensing-patch for the compensation of the interferometric non-linearity. In this paper, a sensing-patch that comprises an EFPI and a piezo ceramic(PZT) is fabricated and the characteristics of the sensing-patch are experimentally investigated. A simple and practical logic is applied for the real-time tracking of optical phase of an interferometer. Experimental results show that the proposed sensing-patch does not have the non-linear behavior of conventional EFPI and hysteresis of piezoelectric material. Moreover, it has good strain resolution and wide dynamic sensing range. Finally, the vibration control with the developed sensing-patch has been performed using Fuzzy logic controller, and the possibility of sensing-patch as a sensoriactuator is considered.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1939-1944
• /
• 2000

Different test methods were used to measure and compare the loss factor of a steel beam. They are free vibration logarithmic decay method, half-power bandwidth method using narrow-band analysis, wide-band analysis method with inverse FFT. In these tests, specimens are clamped at one end. Free vibration method and half-power bandwidth method gave good results. Effect of vibration pick-ups were tested. We also tried center excitation method but could not obtain loss factor.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.173-173
• /
• 1999

The initial growth mode of Nb on Ag(110) in sub-monolayer region is studied using Scanning Tunneling microscopy. E-beam evaporated Nb is deposited onto the substrate at RT, and STM measurements are carried out at RT and 78K. With Nb being immiscible in bulk Ag, 3D islands formation begins at early stage and no particular ordered structure is found. At very low coverages, however, many interesting phenomena are observed in association with Nb clusters. Small Nb clusters as deposited displays very strong size dependence against atom-manipulation by the STM tip. In addition, the apparent corrugation of clusters below the critical size exhibits dramatic dependence on the imaging bias, disappearing completely over a wide range of the bias. Possible physical mechanism responsible for such behavior will be discussed.

• 천문학회보
• /
• 제42권1호
• /
• pp.57.1-57.1
• /
• 2017

As an upgrade we report the current ASTE ultra-wideband corrugated horn design. The length of the feedhorn gets shortened from 12.5 mm to 11 mm, and it shows better side lobe level at the far-field patterns compared with the previous design. We looked into possible quasi-optical solution to match the feedhorn beam to the optics of the current ASTE telescope, starting from frequency-independent solution using two ellipsoidal mirrors to which wideband performance of the feedhorn naturally fits. We used a commercial physical optics package (GRASP) with an user-defined optimizer to give physical constraints to evaluated optical designs for highest efficiency.

• 제어로봇시스템학회논문지
• /
• 제4권6호
• /
• pp.747-752
• /
• 1998

Ultrasonic sensors have been widely used to recognize the working environment for a mobile robot. However, their intrinsic problems, such as specular reflection, wide beam angle, and slow propagation velocity, require an excessive number of sensors to be integrated for achieving the sensing goal. This paper proposes a new measurement scheme which uses only two sets of ultrasonic sensors to determine the location and the type of a target surface. By measuring the time difference between the returned signals from the target surface, which are generated by two transmitters with 1 ㎳ difference, it classifies the type and determines the size of the target surface. Since the proposed sensor system uses only two sets of ultrasonic sensors to recognize and localize the target surface, it significantly simplifies the sensing system and reduces the signal processing time so that the working environment can be recognized in real time.

• 전자공학회논문지A
• /
• 제31A권9호
• /
• pp.114-120
• /
• 1994

We have been successfully fabricated the low nois HEMT device with AlGaAs and GaAs structure. The epitazial layer with n-type AlgaAs and undoped GaAs was grown by molecular beam epitaxy(MBE) system. Ohmic resistivity of the ource and drain contact is below 5${\times}10^{6}{\Omega}{\cdot}cm^{2}$ by the rapid thermal annealing (RTA) process. The ideality factor of the Schottky gate is below 1.6 and the gate material was Ti/Pt/Au. The HEMTs with 0.25$\mu$m-long and 200$\mu$m-wide gates have exhibited a noise figure of 0.65dB with associated gain of 9dB at 12GHz, and a transconductance of 208mS/mm.