• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.231-237
• /
• 2015

The pin-gear drive is a special form of fixed-axle gear mechanism. A large wheel with cylindrical pin teeth is called a pinwheel. As pinwheels are rounded, they have a simple structure, easy processing, low cost, and easy overhaul compared with general gears. They are also suitable for low-speed, heavy-duty mechanical transmission and for occasions with more dust, poor lubrication, etc. This paper introduces a novel slewing ring bearing with an external pinwheel gear set (e-PGS). First, we consider the exact cam pinion profile of the e-PGS with the introduction of a profile shift. Then, the contact stresses are investigated to determine the characteristics of the surface fatigue by varying the shape design parameters. The results show that the contact stresses of the e-PGS can be lowered significantly by increasing the profile shift coefficient.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.819-826
• /
• 2000

This study was performed to develop a measurement system of tractor field performance for plow and rotary operations. Measurement system for tractor consisted of torque sensors to measure torque of drive axles and PTO axle, speed sensors to measure rotational speed of drive axles and engine, microcomputer to control data logger, and data logger as I/O interface system. The measurement system was installed on four-wheel-drive tractor. Four-element full-bridge type strain gages were used for torque measurement of drive axles and optical encoders were used to measure speeds of drive axles and engine. Slip rings were mounted on the rotational axles. Signals from sensors were inputted to data logger that was controlled by microcomputer with parallel communication. Sensors were calibrated before the field tests. Regression equations were found on completion of the calibrations. The field experiment was performed at paddy fields and uplands. Rotary and plow were used when the tractor was operated in the field. Travelling speeds of the tractor were 1.9 km/h, 2.7 km/h, 3.7 km/h, 5.5 km/h, 8.2 km/h, and 11.8 km/h. Operating depths of implements were maintained approximately 20cm during the tests. Torque data of drive axles were different at each location during plow and rotary operations. Results showed that torque of rear axles were greater than those of front axles. Total torque were 6860 - 11064 Nm at the upland and 7360 - 14190 Nm at the paddy field for plow operations. It was found that torque at the paddy field were about 20% greater than those at the upland for plow operations. Torque data showed that rotary operations required less power than plow operation at the paddy field and the upland. Torque measurements at each axle for rotary operations were only 8 - 16% of plow operations in the upland and 15 - 20% in the paddy field.

• 한국도로학회논문집
• /
• 제11권4호
• /
• pp.69-78
• /
• 2009

경부고속도로 건설을 기점으로 급격한 경제성장을 이룬 우리나라 고속도로는 현재 신규도로의 건설사업 물량이 둔화되면서 기존의 도로망을 효율적으로 활용하고 최적의 공용성 유지가 필요한 시점이 되었다. 최적의 공용성 확보를 위해 교통하중을 가장 적극적으로 통제하는 방법은 과적단속이다. 본 연구에서는 과적단속의 효율화를 위해 고속축하중측정 시스템을 개발하고 이를 통해 국내 고속도로 과적화물차 행태 분석을 실시하며, 본 시스템을 활용한 과적단속시스템 개발 가능성에 대하여 검토하는 것을 목적으로 하였다. 본 연구에서 개발한 고속축하중측정 시스템은 차로당 2조의 루프센서와 2조의 축중센서, 2조의 원더링센서로 이루어져 있다. 특히 원더링센서는 차량의 좌우 타이어의 위치 판독이 가능하여 과적단속 시스템으로 활용시 차로의 이탈유무를 판독할 수 있으며, 윤거 측정 및 윤형식(단륜/복륜) 구분이 가능하여 차종을 구분함에 있어서 기존 차종분류 시스템보다 세분화된 분류가 가능하여 12종 차종분류시 오분류 비율이 매우 낮은 장점을 가지고 있다. 본 시스템에 대한 검증시험 결과 모든 시험조건의 전체평균오차가 축하중 15% 이내, 총하중 7% 이내로 나타났다. COST-323에서 제시하고 있는 WIM 등급기준에 따르면 사회기반시설 설계와 유지관리 및 평가목적으로 사용가능한 B(10) 등급으로 나타났으며, 과적이 가장 문제되는 5축 카고 화물차에 대한 분석결과는 축중량 오차 8%, 총중량 오차 5%로 단속가능 수준인 A(5)등급으로 나타났다. 고속도로의 차종별 중량분석 결과 12종 분류기준에서 5종, 6종, 7종, 12종 차량이 하중기준을 초과하는 비율이 가장 높게 나타났으며, 주로 가변축을 장착한 차량으로 축조작에 의한 축하중 과적비율이 매우 높게 나타나 이러한 차량에 대한 실효성 있는 과적단속기법이 필요한 것으로 판단된다. 도로교통분야에 있어서 차종별 교통량 자료는 도로의 계획과 건설, 유지관리, 교통류분석 및 도로행정에 필요한 기본 자료이며 각종 연구에 필요한 기초자료로 활용되어지는 필수적인 요소이다.

• 한국도로학회논문집
• /
• 제8권3호
• /
• pp.143-153
• /
• 2006

본 연구는 콘크리트 도로 포장에 복륜 단축, 복륜 복축, 복륜 삼축 등 복륜 다축 하중이 포장의 중앙부와 모서리부에 작용할 때 포장의 응력 분포 및 최대 응력의 차이를 분석하고 이러한 응력의 차이가 콘크리트 탄성계수, 슬래브 두께, 그리고 지반 탄성계수에 따라 어떠한 특성을 갖는지를 분석하기 위하여 수행되었다. 변환영역에서의 해석법을 이용하여 중앙부 하중에 의한 응력을 구하였으며 유한요소법을 이용하여 모서리부 하중에 의한 응력을 구하였다. 여러 가지 변수에 대하여 중앙부 하중에 의한 최대 응력과 모서리부 하중에 의한 최대 응력을 비교하였으며 이러한 최대 응력 비율을 예측할 수 있는 공식을 개발하였다. 이러한 공식을 이용하여 중앙부 하중에 의한 최대 응력에서 모서리부 하중에 의한 최대 응력을 예측하여 최대 응력 비율 예측 공식의 정확성을 검증하였다. 연구결과 중앙부와 모서리부 하중에 의한 콘크리트 포장의 최대 응력 변화 경향은 매우 비슷하였으며 종방향 상의 최대 응력 발생 위치는 일치하였다. 모서리부 하중에 의한 최대 응력을 중앙부 하중에 의한 최대 응력으로 나눈 최대 응력 비율은 하중 축 수가 많아질수록 감소하며, 콘크리트 탄성계수가 증가, 슬래브 두께가 증가, 지반 탄성 계수가 감소, 그리고 하중 접지압이 증가할수록 커지게 된다.

• 드라이브 ㆍ 컨트롤
• /
• 제19권4호
• /
• pp.19-28
• /
• 2022

This paper introduces an automatic steering system for straight traveling capable of being mounted on drivable agricultural machinery which user can handle it such as a tractor, a transplant, etc. The modular automatic steering device proposed in the paper is composed of RTK GNSS, IMU, HMI, hydraulic valve, and wheel sensor. The path generation method of the automatic steering system is obtained from two location information(latitude and longitude on each point) measured by GNSS in advance. From HMI, a straight path(AB line) can be created by connecting latitude and longitude on each point and the device makes the machine able to follow the path. During traveling along the reference path, it acquires the real time position data every sample time(0.1s), compares the reference with them and calculates the lateral deviation. The values of deviation are used to control the steering angle of the machine using hydraulic valve mounted on the axle of front wheel. In this paper, Pure Pursuit algorithm is applied used in autonomous vehicles frequently. For the analysis of traveling characteristics, field tests were executed about these conditions: velocity of 2, 3, 4km/h which is applied to general agricultural work and ground surface of solid(asphalt) and weak condition(soil) such as farmland. In the case of weak ground state, two experiments were executed about no-load(without work) and load(with work such as plowing). The maximum average deviations were presented 2.44cm, 7.32cm, and 11.34cm during traveling on three ground conditions : asphalt, soil without load and with load(plowing).

• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.33-48
• /
• 1977

Transporting agricultural products and the other material by the two-wheel-tractor (power-tiler)and trailer system may be one of its most widely used farming functions.The safety and hitching load for all the previaling performing conditions may be the general concern over the operation of the tiller-trailer system. In this study, a mathematical model to determine the static and dynamic forces excerting on the hitch point were developed . Based on the analysis of the model and the field measurements. the limiting hitching load and critical slope were analyzed. The results of the study are summarized as follows ; 1) The limit angle of slope land for the safety steering that two-wheel tractor-single axle trailer system was able to transport agricultural products was the direct angle (${\gamma}$) = 8 ; the cross angle$\beta$) 15 ; and it was decreased in accordance with the increase of carrying load ($W_4). 2) The critical velocity for safe operation in case of running on downward hill road was about 1.08m/sec. 3) The limiting carrying load for the safe steering was W$_4$=600kg. The degree of the safe steering for different braking methods was given in order as follows ; Simulataneous braking the tractor and trailer , braking the trailer only, and braking tractor only. 4) Among the three components of impact loads excerting on the hitch point, the component in the lateral direction ($P_{Vy}$) was near zero in spite of increase of hitching load ($W_4) , while the components in the other two mutually perpedicular directions ($P_{Vx}$ and ($P_{Vz}$) ) had larger values in horizontal plane than those in the slope lands. 5) Moment of forces on the lateral direction (M$y$) had the largest value among the three components of impact moment acting on the hitch point, however all the components were sharply increased in accordance with the increase of hitching loads ($W_4. Three components of the moment were the negative values.

• 한국철도학회논문집
• /
• 제17권1호
• /
• pp.28-34
• /
• 2014

본 논문에서는 레일형 초고속 열차의 개념 설계안을 제안하고 동역학 해석을 통해 주행 동특성을 예측하고자 한다. 초고속 열차에는 단일 윤축세트가 포함된 새로운 형태의 대차가 적용되었으며, 기존의 일체형 차축 대신 독립차륜이 적용되었다. 초고속 열차의 동특성을 파악하기 위하여 먼저, 차량에 대한 동역학 수치해석모델을 개발하고 고유치 해석을 통해 해석 모델의 기본적인 타당성을 검증하였다. 또한, 임계속도 해석을 통하여 기존 고속철도 HEMU-430X 차량에 비해 향상된 성능을 확인하였으며, 7000R 곡선선로에서 550km/h 주행해석을 통하여 횡압, 탈선계수 등을 예측하고 초고속 열차 개념 설계안의 적용 가능성을 파악하였다.

• Computers and Concrete
• /
• 제13권4호
• /
• pp.569-585
• /
• 2014

In this paper, a four-layer road structure consisting of an edge transverse crack is simulated using three-dimensional finite element method in order to capture the influence of a single-axle wheel load on the crack propagation through the asphalt concrete layer. Different positions of the vehicular load relative to the cracked area are considered in the analyses. Linear elastic fracture mechanics (LEFM) is used for investigating the effect of the traffic load on the behavior of a crack propagating within the asphalt concrete. The results obtained show that the crack front experiences all three modes of deformation i.e., mode I, mode II and mode III, and the corresponding stress intensity factors are highly affected by the crack geometry and the vehicle position. The results also show that for many loading situations, the contribution of shear deformation (due to mode II and mode III loading) is considerable.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.303-310
• /
• 2011

This paper is focused on development of models for measuring lateral and vertical track irregularities from corresponding accelerometers of an in-service high-speed train. Generally, the track irregularity was measured by a special railway inspection vehicle or system with contact or non-contact sensors. However, the sensors are very expensive and vulnerable to a harsh environment. Displacement estimation from an inertial measurement unit and its wave-band filtering was already developed in the previous study, and it was found that their results included not only the track irregularities but also other information such as phase delay of the applied filters, and suspension and conicity of the wheel. To identify the track irregularities from those results, a compensation filtering method was proposed. Each directional compensation filter was derived by using a system identification method with the estimated directional displacement as input and the corresponding track irregularities as output. In this paper, they are integrated into a model for each direction and applied to the measured lateral and vertical acceleration data from the axle-box and bogie of an in-service high-speed train. Their results are compared with the data from the track geometry measurement system. From the comparison, the proposed models are a useful tool for the measurement of the track irregularities using accelerometers of in-service high-speed trains.

• Elastomers and Composites
• /
• 제55권2호
• /
• pp.88-94
• /
• 2020

Automobile industry, along with the automobile steering system, is rapidly changing and developing. The constant velocity joint transmits power to the wheels of vehicles without changing their angular velocity based on the movement of the steering wheel. Moreover, it controls their movement to act as a buffer. In order to prevent the excessive increase in temperature caused by the movement of vehicles, boots are attached to the constant velocity joint and lubricant is injected into the boots. The boots maintain the lubrication and protect the constant velocity joint from sand, water, and so on. As the wheels of the vehicle rotate, the boots are acted upon by forces such as bending, compression, and tension. Additionally, self-contact occurs to boots. Therefore, their durability deteriorates over time. To prevent this problem, polychloroprene rubber was initially used however, it was replaced by thermoplastic polyester elastomers due to their excellent fatigue durability. In this study, the structural analysis of boots was conducted. The results showed the deformation patterns of the boots based on the translation and rotation of the constant velocity joint. Moreover, it confirmed the location that was vulnerable to deformation. This study can be used to potentially design high-quality constant velocity joint boots.