• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.2102-2104
• /
• 2004

In this study, sheathless electrospray from PDMS/glass microchips with conducting metal emitter tip is described. A chip-based capillary electrophoresis/mass spectrometry (CE/MS) system has advantages of the CE separation and on-line electrospray detection of peptide solution. We have fabricated a new electrospray ionization(ESI) device composed of the metal emitter tip and CE separation channel monolithically in a glass microchip. The separation channel and metal emitter tip are fabricated using a glass wet etching and gold electro plating process, respectively. The fabricated micro electrospray chip was tested by spraying peptide sample for mass spectrometric analysis. Singlely-charged peak and doublely-charged peak of peptide were detected and further MS/MS fragmentation was performed in each peak. Direct comparisons with conventional glass or fused silica emitters showed very similar performance with respect to signal strength and stability.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.423-423
• /
• 2012

Recently, many researchers made progress in various studies improving the efficiency of dye-sensitized solar cell. In this paper, we used glass textured by wet-chemical etching process for improvement of photocurrent density in dye-sensitized solar cells. This is owing to increase coefficient of light utilization. Consequently, DSSC using the textured glass exhibit a Jsc of 9.49 mA/$cm^2$, a Voc of 0.73 V and a fill factor (FF) of 0.67 with an overall conversion efficiency of 4.64. This result showed increasing of 20% current density and 16% conversion efficiency using the textured glass. These results suggested that glass texturing was very effective in controlling the light-scattering properties into the photovoltaic cell.

• Progress in Superconductivity
• /
• 제11권1호
• /
• pp.72-77
• /
• 2009

Low temperature scanning laser microscopy (LTSLM) can be used for a two-dimensional display of bolometric response arising from the localized excitation of a sample by the focused laser beam. In this study, the distribution of critical temperature ($T_c$) and critical current density ($J_c$) in YBCO coated conductor were analyzed using LTSLM. For improving the temperature stability, we have modified the system into a double-shielding type. Through the modification, the temperature stability was successfully improved from ${\pm}10mK\;to\;{\pm}2mK$. The superconducting properties of YBCO coated conductors were measured for the sample of a narrow bridge type using wet etching process. The spatial non-uniformity of the ac voltage response, ${\delta}V(x)$, which is proportional to ${\partial}\rho(x,J_B)/{\partial}T$ in the transition temperature region could be observed and displayed in a two-dimensional image.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.289-292
• /
• 2009

본 연구에서는 감광유리를 이용한 PEM 마이크로 연료전지 바이폴라 플레이트의 제작 공정을 확립하고 성능 측정을 수행하였다. 감광유리는 무게가 가볍고 내화학성이 뛰어나며 제작이 용이하다. 비등방성 식각, 열 및 UV 접합, 그리고 금속 층 적층을 통한 MEMS 제작 공정이 확립되었다. 성능 측정 결과 활성화 영역에 은이 적층된 마이크로 연료전지의 성능이 그렇지 않은 것보다 우수하였으며 두 경우에서 측정된 마이크로 연료전지의 성능은 모두 국내외 마이크로 연료전지 연구 수준과 동등한 수준이었다.

• 마이크로전자및패키징학회지
• /
• 제27권3호
• /
• pp.9-19
• /
• 2020

기능성 나노박막을 손상 없이 목표기판으로 옮기는 전사 기술은 나노박막 기반의 차세대 응용 제품 개발을 위한 초석이다. 본 논문에서는 최근 나노박막 전사의 연구 동향을 박막-기판 계면의 박리 원리에 따라 습식 식각 전사, 전기화학적 박리, 기계식 전사 방법 세 가지로 분류하여 간단하게 살펴볼 것이다. 더 나아가, 손쉽고, 기판 재활용이 가능하며, 광범위한 적용 가능성을 가지고 있어 유망 기술로 간주되는 기계식 전사 방법에 대하여 파괴 역학적 관점에 초점을 맞추어 다룰 것이다. 마지막으로, 나노박막의 기계식 전사 방법의 기술 성숙도를 향상시키기 위한 향후 도전 과제와 방향성에 대하여 고찰하고자 한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.813-815
• /
• 2008

We prepared highly transparent and conductive Oxide/Metal/Oxide(OMO) multilayer by sputtering and developed wet etching process of OMO with a clear edge shape for the first time. The transmittance and sheet-resistance of the OMO are about 89% and $3.3\;{\Omega}/sq.$, respectively. We adopted OMO as a gate electrode of transparent TFT (TTFT) array and integrated OLED on top of the TTFT to result in high aperture ratio of bottom emission AM-OLED.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.91-94
• /
• 2007

마이크로 고체 추진제 추력기의 점화 시스템의 제작 및 점화 실험에 관한 연구 결과를 기술하겠다. 유리 박막 마이크로 백금 점화기는 일반적인 금속 박리 공정과 감광 유리 제작 공정을 이용하여 제작되었다. 백금 층의 두께는 $2000{\AA}$, 점화기 패턴의 폭은 $40{\mu}m$ 였다. 제작된 유리 박막의 두께는 $15{\mu}m$, 유리 박막의 지름은 1 mm 였다. HTPB/AP 추진제를 이용하여 점화 실험을 수행하였다. 12 V의 전압을 사용한 경우, 점화 지연 시간은 1.6 s 였으며 이 때의 점화 에너지는 1.4 J로 측정되었다.

• 반도체디스플레이기술학회지
• /
• 제10권1호
• /
• pp.91-94
• /
• 2011

This paper presents light transmission efficiency by optical adhesive thickness between MLA and aperture layer and by aperture hole size. The gap between MLA and Aperture layer is adjusted by the shim. The more optical adhesive thickness increases, the better light transmission efficiency increases up to a point. After that, the light transmission efficiency decreases because stray lights cannot transmit through the aperture layer owing to cut-off by aperture layer. And as a result of light transmission efficiency with changing aperture hole size, the light transmission efficiency is proportional to area of aperture hole. The more specified process is made, the better data and sample will be got.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1623-1624
• /
• 2006

It is a paper for design, manufacture and estimation of industry inkjet head. Simulations for Actuator, Ink flow and Ejection are executed for securing design ability. Relations between droplet and properties of ink are explained closely through simulation for nozzle. Actually, two silicon plates are made by dry and wet etching and directly bonded. PZT materials is attached on the bended ink flow part and cut to $540{\mu}m$ interval by dicing saw. Actuator was seen variation within 10% between simulation and actual head. Through the ejection estimation, it is shown that stabilized driving voltages change according to viscosity and surface tension of metal ink. Using the metal ink of viscosity of 4.8 cps and surface tension of 0.025 N/m, it is possible to eject the stable droplets with 5m/s, 20 pl, 5 kHz.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.326-329
• /
• 2005

As a flexible method to fabricate sub-micrometer patterns, Focused Ion Beam (FIB) instrument and Self-Assembled Monolayer (SAM) resist are introduced in this work. FIB instrument is known to be a very precise processing machine that is able to fabricate micro-scale structures or patterns, and SAM is known as a good etch resistance resist material. If SAM is applied as a resist in FIB processing fur fabricating nano-scale patterns, there will be much benefit. For instance, low energy ion beam is only needed for machining SAM material selectively, since ultra thin SAM is very sensitive to $Ga^+$ ion beam irradiation. Also, minimized beam spot radius (sub-tens nanometer) can be applied to FIB processing. With the ultimate goal of optimizing nano-scale pattern fabrication process, interaction between SAM coated specimen and $Ga^+$ ion dose during FIB processing was observed. From the experimental results, adequate ion dose for machining SAM material was identified.