• Journal of Welding and Joining
• /
• v.10 no.3
• /
• pp.1-12
• /
• 1992

A literature review was conducted to survey informations available on the welding metallurgy of aluminum alloys and its effect on fusion weldability, especially on solidification cracking and pore formation. Solidification cracking behavior of Al weld is a complicate matter as compared to other high alloys, where a relatively simple Fe-X(most detrimental elements S, P, B, Si, etc) binary diagram can be successfully applicable. Both additive and synergistic effects of elements should be considered together. A same element play a different role from system to system. Porosity, caused by hydrogen contamination of the weld is one of the most troublesome welding problems. The primary sources of hydrogen are believed to be an absorbed moisture on the filler metal or base metal and in the shielding gas. It is extremely important that reliable quality-control procedures be employed to eliminate all possible sources of hydrogen contamination. Selection of proper process and parameters is sometimes more important than controlling of alloying elements in order to make a defect-free weld.

• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.62-68
• /
• 2016

Laser welding has superior characteristic such as low distortion, high welding speed, easy automation and real time control. But it is easy to occur weld defects such as porosity, crater, humping bead in the area of welding start and end. These weld defects can be suppressed by applying the wave shape control. In this study CW fiber laser was used for welding of $0.5mm^t$ pure titanium. Penetration properties were evaluated with the time of slope up and down. After then the bead shape was observed, and the maximum depth and the area of crater were measured. The bead shape of welding start area changed to be sharp with increase of slope up time and non-weld area of welding start increased. The crater and humping bead were suppressed with slope down time. The cooling rate of crater area was understood through measure of the hardness. Also, The distribution tendency of alloying elements was observed by EPMA and EDS. When wave shape control didn't applied to weld, the hardness of end weld increased due to rapid cooling rate and the hardness of rear part in the crater was higher than that of fore part. On the other hand, when the wave shape control was used for end weld, the increase of hardness in the end weld couldn't be found due to gradual cooling rate.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.5
• /
• pp.135-143
• /
• 2000

The vision system is easy to use the exclusive use as a independent computer system but it is not much popularization by reason of expensive and difficult to adapt to the various fields, because it is easy to the existed computer system, the price is cheap and also it can use to the various measurement purpose which user wanted and programed. The measurement method of the vehicle axle casing nut welding part is that measure the value of the welding part to adapt the actual operation program from using the ratio between the actual length of the standard specimen and the length of image, to measure the ratio between the actual product and the camera image. A defect is found by the assembled visual inspection system. The inspection algorithm which estimates the quality of welded product is developed and also, the software program which processes the automatic test function of the inspection system. We make the foundation of the inspection automatic system and we will help to apply other welding machine.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.23-31
• /
• 1997

The results of high speed photography, acoustic emission detection and plasma UV radiation intensity measurement during CO2 laser welding of stainless steel 304 are presented. Video images with high spatial and temporal resolution allowed to observe the melt dynamics and keyhole evolution. The existence of a high speed melt flow which originated from the part of weld pool and flowed along the sides wall of keyhole was confirmed by the slag motion on the weld pool. the characteristic frequencies of flow instability and keyhole fluctuations at different welding speed were measured and compared with the results of Fourier analyses of temporal acoustic emission (AE) and light emission (LE) spectra. The experimental results were compared with the newly developed numerical model of keyhole dynamics. (The model is based on the assumption that the propagation of front part of keyhole into material is due to the melt ejection driven by laser induced surface evaporation.) The calculations predict that a high speed melt flow is induced at the front part of keyhole when the sample travel speed exceeds several 10mm/s. The numerical analysis also shows the hump formation on the front keyhole wall surface. Experimentally observed melt behavior and transformation of the AE and LE spectra with variation of welding speed are qualitatively in good agreement with the model predictions.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.55-59
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.21-23
• /
• 2003

• Proceedings of the KWS Conference
• /
• 1992.10a
• /
• pp.210-212
• /
• 1992

• Journal of Welding and Joining
• /
• v.23 no.3
• /
• pp.47-53
• /
• 2005

Longitudinal deformation is produced by fillet welding during the fabrication of built-up beams and decreases productivity and quality because it needs an extra correcting process. The deformation is caused by welding moment, which is the value multiplied the welding shrinking farce by the distance from the neutral axis. This welding moment can be offset by generating a moment in the same magnitude and in an opposite direction by induction heating. The location and quantity of the induction heating are decided via experiments and simple equations. This study, first, clarifies the creation mechanism of the longitudinal deformation with FEM analysis. Then, we presents the preventive method of this deformation by induction heating basing on the mechanism and verifies its validity through analysis and experiments.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.185-188
• /
• 2006

The sea water pipe of engine room in all kinds of ships is being surrounded with severe corrosive environment. Therefore it's leakage part due to corrosion is inevitably prevented by various welding method. In this case corrosion property of welded zone may be considerably different by each welding materials. In this study corrosion resistance of the welded zone of sea water pipe with some welding materials such as shielded metal arc welding materials, inert gas arc welding materials was investigated with electrochemical method.

• Laser Solutions
• /
• v.13 no.4
• /
• pp.14-20
• /
• 2010

Robot path generation and laser welding technology for manufacturing automotive body are studied. Laser welding and industrial robot systems are used with the robot based laser welding system. The laser system used in this study is 1.6kW Fiber laser, while the robot system is 6 axes Industrial robot (payload: 130kg). The robot based laser welding system is equipped with laser scanner system for remote laser welding. The laser source, robot and laser scanner system are used to increase the processing speed and to improve the process efficiency. The welding joints of steel plate are butt and lapped joints. The quality test of the laser welding are through the observation the shape of bead on plate and cross-section of welding part. The 3 dimensional laser welding for non-linear pipe welding line is performed. This paper introduces the robot based laser welding system to resolve the limited welding speed and accuracy of the conventional spot welding system.