• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.3
• /
• pp.81-88
• /
• 2002

The root joint in the welding structures are apt to failure by the stress concentration which is occurred by the external force. Therefore, in the safety and reliability of structure, the complete penetration joint welding which are obtained by the groove welding with edge preparation is generally required. Nevertheless, fillet T-joint welding without edge preparation is often carried out in the fields to reduce working time and consumption of welding electrode, however, this process is likely to produce inadequate joint penetration such as root gap. In this paper, the focus of research is to investigate distribution of welding residual stresses in the plate(or flange) and web of T-joint weld, and especially in the near of root gap notch that is due to incomplete joint penetration. For the analysis, we have chosen model of T-joint weld in the cases of single and multi-pass welding with submerged arc welding and analyzed model by using finite element programs considering the heat conduction and thermal elasto-plastic theory.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.35-42
• /
• 1969

Penetrations of arc welding electrades are different by changing welding conditions, welding speed of travel and current, even though quite same ones. Changing status of penetration is studied by changing welding speed of travel keeping welding current constant, at first, and by changing welding current keeping welding speed of travel which was obtained prior experiment constant, afterward. The F-100 4mm $\phi$ rods, E4301 class, which covering substance is mainly ilmenite and a domestic representative product of this class electrode, are used for this experiment. The Marquette's No.130 5/32"(4mm)$\phi$ rods, E6011 class, and No. 140 5/32"(4mm)$\phi$, E6013 class, which were produced in the United Stated, are used to compare penetration with F-100 at same welding conditions. The covering substance of Marquette's No. 130 rods is mainly cellulose, and belong to deep penetration arc welding electrodes, the covering material of another rods is titania, and a kind f shallow penetration rods. The result of this study is as follow : penetration of F-100, domestic ilmentite covering electrade, E4301 class, is between E6011 and E6013 of the United States products. At the lower range of welding current, penetration is closer to E6013 than E6011, at the higher range, closer to E6011 than another; and the value of penetration ranges $1.65{\sim}2.70mm$ for 4mm$\phi$ rods in the adequate current range. The changing status of penetration is showed by following experimental formula. $P=KE_v^{-\frac{2}{5}}1^{\frac{3}{2}}$

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1240-1247
• /
• 2008

Leakage trouble on the sea water pipeline in engine room is often resulted from a localized corrosion due to severe corrosive environment caused by both high speed and high pressure of sea water flowing through the inner pipe. In addition, when the ship is in stand-by or emergency condition, underwater welding to control the leakage of sea water from a hole of its pipe is very important in an industrial safety point of view. In this study possibility of underwater welding to control leakage of sea water and corrosion property of its welding zone were investigated with the electrochemical methods by parameters of welding methods and welding electrodes when underwater welding is achieved with a such case that sea water is being leaked out with a height at 50mm from a hole of $2.5mm{\emptyset}$ of test pipe. Corrosion resistance of weld metal zone is better than the base metal and its hardness is higher than that of the base metal. However corrosion potential of weld metal zone showed a negative value than that of the base metal, therefore weld metal zone is preferentially corroded rather than the base metal by performance of galvanic cell due to difference of corrosion potential between weld metal zone and base metal. Eventually it is suggested that leakage of sea water is successfully controlled by underwater welding,

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.88-93
• /
• 2021

SAW (Submerged Arc Welding) is often used for ship construction or welding pressure vessels and involves spraying a flux in a powder form to a welding site to a certain thickness and continuously supplying electrode wires therein. This welding method enables high current welding up to 1,500 to 3,000 A. Arc efficiency is higher than 95% and the technique allows clean work as it creates less welding fume, which is composed of fine metal oxide particles, and the arc beam is not exposed. In this study, SM490C-TMC thick plates were heterogeneously welded by SAW. Mechanical properties of welds were measured, and welds were assessed macroscopically and for adhering magnetic particles. The following conclusions were drawn. Bending tests showed no spots exploded on sample surfaces or any other defect, and plastic deformation testing confirmed sufficient weld toughness. These results showed the 1F welding method has no shortcomings in terms of bending performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.3
• /
• pp.272-280
• /
• 2002

The recent research topics on $CO_2$ arc welding power supplies are focused mainly on the reduction of spatter generation. The method for reducing the spatters can be approached in several ways: finding the new materials fur consumable electrode and shielding gases, researching on the circuit topology and the controller. In this paper, the metal transfer and several control methods for the $CO_2$ GMAW were described. And it was proposed and compared with other schemes that the control method for reducing spatter by controlling the welding current when short-circuit and re-ignition.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.61-68
• /
• 1999

For the last two decades, waveform control techniques have been successively developed and applied for the inverter welding machines resulting in the substantial reduction of spatter generated in CO₂ welding. One of the constituents commonly involved in those techniques is to delay the instant of current increase to some extent after the initiation of short-circuiting. Although this technique has been known to be quite effective in reducing the spatter generation through the suppression of is instantaneous short circuiting, the delay time necessary for minimum spatter has not been clearly understood. In this study, the control system for varying the delay time was constructed so that the spatter generation rates could be measured over a wide range of delay time, 0.29-2.0 msec. As a result of this study, it was demonstrated that spatter generation rate(SGR) sharply decreased at delay time of 0.6 msec and longer accompanied with the change in characteristics of short circuit mode from the instantaneous short-circuiting(ISC) dominant to normal short-circuiting(NSC) dominant. Another feature that have been found in current waveform of over 0.6msec was the creation of current pulse right after the arc reignition stage. Because of this current pulses weld pool oscillated in wave-like fashion and it looks like to play an important role in developing short circuiting between electrode and weld pool.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.288-290
• /
• 2007

Ir-192 source is one of the most widely used radioisotopes in the field of non-destructive testing applications. To obtain radiation safety it is necessary to take into consideration integrity of welded joint in the production of sealed radiation source. Generally, the quality of a resistance welded joint is strongly influenced by process parameters during the welding process such as current, welding time and applied force. In this study, resistance welding technology and system were developed for sealing of Ir-192 industrial radiation source capsules. In order to evaluate the weld quality in real time, quantitative relationships between process parameters and electrode displacement were also established.

• Journal of Welding and Joining
• /
• v.7 no.4
• /
• pp.30-37
• /
• 1989

Effect of heat treatment on mechanical properties of an overlay weldment was investigated. Over welding was carried out on the structural C-Mn mild steel substrate to take required test specimens. Shielded metal arc welding process with 13Cr-0.2Ni stick electrode was applied. The heat treatment temperatures and holding times were $450{\circ}C., 550{\circ}C., 650{\circ}C., 750{\circ}C., 850{\circ}C.$ and 0.5hr, 2hr, 10hr, respectively. Mechanical tests and microscopic inspection were also carried out to investigate welds soundness. Test results indicated that carbon migration was dominant near bonded zone. At temperature of around 650.deg. C, carburized layer and decarburized layer were formed remarkably along overlay welds region and C-Mn mild steel region, respectively. The wideth of these layers became wider with increasing heat treatment temperature and/or holding time at the elevated temperature, and this relationship agreed with Larson-Miller parameter. Side bending test results demonstrated that the crack free region of overlay welds could be deduced from the relationship between temperature and holding time.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.3
• /
• pp.79-84
• /
• 2013

The seawater pipes in the engine rooms of ships are surrounded by severely corrosive environments caused by fast flowing seawater containing chloride ions, high conductivity, etc. Therefore, it has been reported that seawater leakage often occurs at a seawater pipe because of local corrosion. In addition, the leakage area is usually welded using shielded metal arc welding with various electrodes. In this study, when seawater pipes were welded with four types of electrodes(E4311, E4301, E4313, and E4316), the difference between the corrosion resistance values in their welding zones was investigated using an electrochemical method. Although the corrosion potential of a weld metal zone welded with the E4316 electrode showed the lowest value compared to the other electrodes, its corrosion resistance exhibited the best value compared to the other electrodes. In addition, a heat affected zone welded with the E4316 electrode also appeared to have the best corrosion resistance among the electrodes. Furthermore, the corrosion resistance of the weld metal zone and heat affected zone exhibited relatively better properties than that of the base metal zone in all of the cases welded with the four types of electrodes. Furthermore, the hardness values of all the weld metal zones were higher than the base metal zone.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.303-306
• /
• 2000

Quality estimation of the weld has been one of the important issues in RSW which is a main process of the sheep metal fabrication in auto-body industry, It was well known that among the various welding process variables, dynamic resistance has a close relation with nugget formation. With this variable, it is possible to estimate the weld quality in real time. In this study, a new quality estimation algorithm is developed with the primary dynamic resistance measured at welding machine timer. For this, feature recognition method of Hopfield neural network is used. Primary resistance patterns are vectorized and classified with five patterns. The network trained by these patterns recognizes the dynamic resistance pattern and estimates the weld quality Because the process variable monitored at the primary circuit is used, it is possible to apply this system to real time application without any consideration of electrode wear or shunt effect.