• Journal of Welding and Joining
• /
• v.16 no.2
• /
• pp.14-20
• /
• 1998

• Proceedings of the KWS Conference
• /
• 1995.04a
• /
• pp.68-70
• /
• 1995

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.19-22
• /
• 2001

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1299-1306
• /
• 2007

The combination of laser beam and electric arc sharing common weld pool has widely been investigated since the late seventies, but it is beginning of the industrial uses. Recently, laser-GMA hybrid welding process showed possibility to overcome the tight gap tolerance with improved productivity. The laser-arc hybrid welding process is inherently complex because it has three kinds of process parameters: arc welding, laser welding and hybrid welding parameters. In this study, the optimum range of the process parameters were determined by high speed image analysis which could unveil the welding phenomena in laser-arc hybrid welding. The laser-arc hybrid welding was applied for position welding from the flat position to the overhead position and the welding characteristics were investigated.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.58-62
• /
• 2010

In this study, the bead-on-plate welding were conducted by using GMA welding and plasma-GMA welding on Al 5052 and, Al 6061 plates. For these processes, the maximum welding speeds for full penetration were compared, and various weld qualities such as bead appearance, cross-section, cracks and porosities were examined. Faster welding speed, cleaner bead surface and more stable drop transfer could be achieved by plasma-GMA welding, compared with GMA welding.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.1
• /
• pp.36-41
• /
• 2013

Friction stir welding (FSW) is a relatively new joining technique particularly for magnesium and aluminum alloys that are difficult to fusion weld. In this study, AZ31 Mg alloys were joined by FSW with shoulder diameter 11, 19 mm and rotating speed 900, 1200, 1500, 1800 rpm. The shoulder diameter and welding speed depended on the heat input during FSW process. As a result, the microstructures of stir zone were a fine grain by dynamic recrystallization. According to the larger shoulder diameter and the higher rotating speed, refined grain sizes of stir zone were grown by higher heat input, and the microhardness of stir zone was lower. The tensile strength at the shoulder diameter 19 mm, rotating speed 900 rpm was obtained maximum value. This value compared with the base metal was over 93%.

• Proceedings of the KWS Conference
• /
• 1999.10a
• /
• pp.43-46
• /
• 1999

It has been suggested that the motivation for automation of welding processes ncludes the replacement and extension of the functions of human operators. Among these types of the welding automation, SAW(Submerged Arc Welding) was prevalently used, because it is highly suited to a wide range of application, especially for the high speed welding. A Significant portion of the total manufacturing time for a pipe fabrication process is spent on the welding following primary machining and fit-up processes. To achieve the reliable weld bead appearance, the automatic seam tracking and adaptive control to fill the groove are urgently needed. This paper proposed the mechanical functions of multi-torches welding system, flux supply and recovery system in conjunction with the complex air pulsing method and various types of methodologies. It was shown that the multi-torches welding system revealed the high welding qualities for the circular and rectangular pipes. In conclusion, the multi-torches welding system developed will contribute the advanced welding technology, welding automation and increment of the market in these areas.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1076-1082
• /
• 2012

Today the welding for LNG carrier is known to be possible using arc and plasma arc welding process. But because of the lower energy density, arc welding is inevitable to multi-pass welding for thick plate and has a limit of welding speed compared to laser which is high energy density heat source. When thick plate is welded, weld defect by multi-pass welding and heat-affected zone by high heat-input were formed. Therefore one-pass welding by key-hole has been considered to work out the problems. It is possible for Laser, electron beam, plasma process to do key-hole welding. Nowadays, plasma process has been used for welding membrane of cargo tank for LNG carrier instead of arc process. Recently, many studies have examined to apply laser process to welding of membrane. In this paper, weldability, microstructure and mechanical properties of stainless steel for LNG carrier welded by fiber laser were compared to those by plasma. As a result, although the laser welding has several times faster speed, similar properties and smaller weld and heat affected zone were obtained. Consequently, this study proves the superiority of fiber laser welding for LNG carrier.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.4
• /
• pp.1-12
• /
• 2007

S45C steel has been widely used in industrial applications, such as crank shafts, gears, main spindles of machine tools, connecting rods, etc., because of its distinguished mechanical property. In the convention arc welding of S45C plates without heat treatments, it is possible for welding defects to take place, such as a void or a hot-crack, due to a high carbon composition of S45C. Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, single-pass thick section capability, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as power of laser and welding speed, on the characteristics of laser welding for the case of nickel coated and nickel uncoated S45C steel. As the result of the experiment, in case of butt welding, nickel coated S45C steel has a uniform formation of welding zone and it was judged that the welding nature was better as inner defects and the quantity of spatter were formed relatively fewer than nickel uncoated S45C steel.

• Journal of Welding and Joining
• /
• v.24 no.1
• /
• pp.56-63
• /
• 2006

The characteristics of $CO_2$ or Nd:YAG laser welded 600MPa ade TRIP steel was investigated. He or Ar gas was used as a shield gas in case of $CO_2$ laser welding, but the shield gas was not used in case of Nd:YAG laser welding. Bead on plate welding was performed with various welding conditions. Defects in the joints of both welding type occurred at 1.8m/min but were not observed over the welding speed of 2.1m/min in case of Nd:YAG laser welding. However, porosity occurred in $CO_2$ laser welding and the tendency of decreasing with the increase of welding speed. The hardness was the highest at heat affected zone near fusion zone as well as at the fusion zone and decreased on approaching the base metal. In a perpendicular tensile test to the weld line, all specimens that have been welded at optimum conditions were fractured at the base metal, and the tensile properties showed the rather higher than those of raw material. In a parallel tensile test, the strength of the joints was higher than that of the base metal. Elongation was found to be lower than that of the raw material. Forming height by Erichsen test and elongation were deeply related with the ratio of base metal/weld metal and the maximum hardness of the weld metal. Also porosity induced to decrease the strength and the elongation. The maximum formability was recorded at approximately 80% as compared with that of the raw material with the optimum condition.