• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.285-287
• /
• 2005

During fabrication of deck house block in passenger ships, the problem of unexpected large deformation and distortion frequently occurs. In this case, line and spot heating method were widely used to correct the distortion of thin plate structure. Spot heating was especially used for the case under 5mm thickness. Few papers are available on the working conditions of spot heating method but only little information on deformation control. In this study, evaluation was carried out on the temperature distribution of spot heating methods using FEA and practical experiments for various heating time. IIn FEA, heat input model was established using Tsuji's double Gaussian heat input mode (Tsuji, I., 1988). This model was verified by comparing with experimental data. Also radial shrinkage and angular distortion due to spot heating were determined and compared with experimental results. Thermo elasto-plastic analysis was performed using commercial FE code, MSC/MARC. Radial shrinkage and angular distortion were measured using 3D measuring apparatus. Based on these results, simplified analysis model for deformation by spot heating was established.

• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.7-12
• /
• 2009

TFT-LCD is the most popular type of flat display panel in the information technology field. The back light unit is a main part of the structure of a TFT-LCD panel. Occasionally, studies have shown that failures of the CCFL of the BLU occur due to the poor weld characteristics of these materials. The aim of this study was to prepare some technical data and to characterize a microjoined electrode for the CCFL. Microstructure examinations, microhardness measurements, resistance measurements and microtensile tests of the microjoined electrode were carried out. The result indicates that a large amount of grain coarsening exists in the heat-affected zone (HAZ) of the weld between the cup and the pin. This grain coarsening of the HAZ between the cup and pin is caused by the welding cycle, which may have an influence on the lowest microhardness values. Fracturing of the microjoined electrode also occurred at the HAZ close to the cup between the weld holding the cup and the pin. Additionally, no specific changes of the electrical resistance among the cup, pin, and lead wire themselves or in the microjoined electrode were observed.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.11 no.2
• /
• pp.126-134
• /
• 2001

Statistical approaches for analysis of data from the limited number of samples in ship building industry(SBI) collected by an industrial hygienist for checking compliance to an occupational standard were considered. Sampling for compliance usually has been guided by judgment selection, rather than true randomness, resulting in the creation of compliance samples which approximate a censored sample from the upper tail of the exposure distribution. Similar exposure groups(SEGs) including welding and painting process were established to assess representative values in each groups after reviewing the whole production line in SBI. For the convenient statistical approaches, the code has assigned to each SEGs. The descriptive statistics and probability plotting were used to yield the representative values in each SEGs. In the first step, SEGs of 558 were established from 5 ship building companies. The 38 SEGs showed the uncertainty are divided into each 5 companies and assessed the representative values again. The 44 SEGs in each companies was not showed the normal and lognormal distribution was analyzed each data. And also, recommendation was suggested to resolve the uncertainty in each groups.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.16 no.4
• /
• pp.398-412
• /
• 2006

The purpose of this study is to investigate the relationship between the acceleration of vibration by the powered hand tools used in the shipbuilding industry, and to develop the prospective prevalence model for the hand-arm vibration syndrome among the shipbuilding workers.The acceleration levels and frequencies of six types of grinder were measured using the ISO5349 method along with the time of exposure to the vibration from the powered hand tools. Medical examination for 114 workers were performed using the cold provocation test. Comparisons were made between the estimated prevalence of hand-arm vibration syndrome from ISO5349 and the observed values from the medical examinations. By multiple regression, we developed the prospective prevalence model of hand-arm vibration syndrome produced by the hand tools used in the shipbuilding industry. 4 hour-energy-equivalent frequency-weighted accelerations were $6.23m/s^2$ in the grinding job done after welding, and $13.39m/s^2$ in the grinding job done before painting. The mean exposure time while holding powered hand tools was 4.64 hours. Prevalence rates of Raynaud's Phenomenon were 12.04% in the grinding after soldering, and 42.9% in the grinding before painting measured using the ISO5349 method. After exposure to vibration for 10.79 years, about a half of the workers in the grinding after welding could developed Raynaud's Phenomenon. For the workers in the grinding before painting, the latency was 5.02 years. The ISO equation for dose response relationship was not significantly correlated with observed recovery rates of finger skin temperatures, blood flows and amplitudes of nerve conduction velocities. A multiple regression model for dose-response relationship was proposed from the results. Recovery rate of the skin temperatures = -0.668+ 0.337 ${\times}$ 4 hour energy equivalent frequency-weighted accelerations + 0.767 ${\times}$ duration of vibration exposure(years) The validity was proved by multiple regression analysis after correlation transformation and regression results based on model-building data and validation data.

• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.37-45
• /
• 2009

An objective of this study is to evaluate the structural performance of the weak axis SRC column-RC beam joints by experiments. Although one of common joint types is the connection with standard hooks, it has been required to examine its safety and to settle problems of the joint among practical engineers. Specimen types are classified into two categories, namely the type of standard hook and the type of shape improvement. The first one is consisted of three specimens which are reference type, development length modification type, and development length supplement type. Three specimens for shape improvement were made with variations on the arrangement of longitudinal reinforcements and the development length. Test results based on cyclic loadings were discussed with load-deflection curves, maximum strengths, strength degradations beyond the maximum. It was found that the standard hook types showed premature failures and consequent strength degradations due to splitting of joint concrete. However, satisfactory performance was obtained with the shape improvement type with wing-plate welding. No premature failures and strength degradations were detected with the specimens.

• Journal of Practical Engineering Education
• /
• v.13 no.3
• /
• pp.461-471
• /
• 2021

This study investigated the application and satisfaction of the global industrial technology curriculum for foreign students at J University in Korea. In order to derive the global industrial technology curriculum, industry needs were analyzed, and the appropriateness of the curriculum was identified through the current status of the root industry. In order to investigate the satisfaction with the application of the global industrial technology curriculum, a questionnaire survey was conducted in the form of an in-person interview for two months from August to September 2021 for foreign students. The questionnaire surveys included general information of the subjects, the status of completion of the curriculum, questions about class satisfaction, the process of obtaining certifications, and whether or not they were employed. As a result of the study, the reasons for choosing the curriculum of the respondents were their interest in subjects related to the root industry (welding, machining, etc.) and the issuance of Korean employment and visas (E-7). The most preferred subject was welding practice at 36.8%, and in terms of subjects considered necessary, the subject of basic major terminology was the most at 29.2%. The difference in satisfaction between graduates and current students who applied the same curriculum was tested, and as a result of the analysis, it was confirmed that there was no difference in satisfaction between current students and graduates through the t test (significance level p=0.05). We believe that this study is meaningful in that it provides basic data for the domestic industrial technology curriculum for foreign students and suggests the direction of related research in a time when the existence of universities is threatened due to the decrease in the school-age population.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4398-4404
• /
• 2015

Stainless steel sheets are widely used as the structural material for dynamic machine structures, These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding, For fatigue design of gas welded joints such as various type joint. It is necessary to obtain design information on stress distribution at the weldment as well as fatigue strength of gas welded joints. Thus in this paper, ${\Delta}P-N_f$ curves were obtained by fatigue tests. and, ${\Delta}P-N_f$ curves were rearranged in the ${\Delta}{\sigma}-N_f$ relation with the hot spot stresses at the gas welded joints. Using these results, the accelerated life test(ALT) is conducted. From the experiment results, an life prediction model is derived and factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of welded joints and data analysis by statistic reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.675-680
• /
• 2002

Cracking and bulging in welded and internally lined pressure vessels that work in thermal-mechanical cycling service have been well known problems in the petrochemical, power and nuclear industries. However, published literature and industry surveys show that similar problems have been occurring during the last 50 years. A better understanding of the causes of cracking and bulging causes is needed to improve the reliability of these pressure vessels. This study attempts to add information required for increasing the knowledge and fundamental understanding required. Typical examples of this problem are the coke drums in the delayed coking units refinery process. This case was selected for experimental work, field study and results comparison. Delayed coking units are among the refinery units that have higher economical yields. To shut down these units represents a high negative economical impact in refinery operations. Also, the maintenance costs associated with repairs are commonly very high. Cracking and bulging occurrences in the coke drums, most often at the weld areas, characterize the history of the operation of delayed coking units. To design and operate more robust coke drums with fewer problems, an improved metallurgical understanding of the cracking and bulging mechanisms is required. A methodology that is based field experience revision and metallurgical analyses for the screening of the most important variables, and subsequent finite element analyses to verify hypotheses and to rank the variables according to their impact on the coke drum lives has been developed. This indicated approach provides useful information for increasing coke drum reliability. The results of this work not only order the most important variables according to their impact in the life of the vessels, but also permit estimation of the life spans of coke drums. In conclusion, the current work shows that coke drums may fail as a combination of thermal fatigue and other degradation mechanisms such as: corrosion at high and low temperatures, detrimental metallurgical transformations and plastic deformation. It was also found that FEA is a very valuable tool for understanding cracking and bulging mechanisms in these services and for ranking the design, fabrication, operation and maintenance variables that affect coke drum reliability.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.467-474
• /
• 2010

Stainless steel sheets are widely used as the structural material for railroad cars and commercial vehicles. Structures made of stainless steel sheets are commonly fabricated by gas welding, For the fatigue design of gas welded joints such as fillet joints, it is necessary to obtain design information of the stress distribution at the weldment as well as the fatigue strength of the gas-welded joints. Further, the influence of the geometrical parameters of gas-welded joints on stress distribution and fatigue strength must be evaluated. in this study, ${\Delta}P-N_f$ curves were obtained by fatigue tests. and, the ${\Delta}P-N_f$ curves were rearranged on the basis of the ${\Delta}{\sigma}-N_f$ relation for the hot-spot stresses at the gas-welded joints. These results, were used for conducting an accelerated life test(ALT) From the experiment results, an acceleration model was derived and factors were estimated. The objective is to obtain the information required for the analysis of the fatigue lifetime of fillet welded joints and for data analysis by the statistic reliability method to save time and cost and to develop optimum accelerated life prediction plans.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.985-993
• /
• 2001

Neural networks are shown to be effective in being able to distinguish incomplete penetration-like weld defects by directly analyzing the plasma which is generated on each impingement of the laser on the materials. The performance is similar to that of existing methods based on extracted feature parameters. In each case around 93% of the defects in a database derived from 100 artificially produced defects of known types can be placed into one of two classes: incomplete penetration and bubbling. The present method based on classification using plasma is faster, and the speed is sufficient to allow on-line classification during data collection.