• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.343-350
• /
• 1999

Orthotropic steel bridge decks are potentially liable to cause fatigue cracks due to weld defects, residual stresses, and in-plane or out-of-plane stresses. In particular, the cracks propagated through deckplate in longitudinal rib to deckplate joints occur at weld toe and weld root due to stress concentrations. Numerical parametric studies are performed to show the Influence of the parameters on the stress concentration at the connection between the longitudinal rib and the deckplate. The parameters include root gap, toe angle $\theta$, toe radius $\rho$, and weld penetration. This study provides a fundamental point for the improvement of fatigue resistance and the estimation of the fatigue crack propagation in wekded joint details.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.85-91
• /
• 2003

Narrow gap welding has many advantages over conventional V-grooved butt welding such as high productivity, small deformation and improved mechanical property of joints. With narrower groove gap, less arc heat input is expected will all the other advantages of narrow gap welding. The main defects of narrow gap welding include the lack of root fusion, convex bead surface and irregular surface, all of which have negative effects on the next welding pass. This paper suggests an up-and-down torch oscillation for ultra narrow gap welding with gap size of 5mm and investigates the proper welding conditions to fulfill the reliable and high welding quality. First, GMA welding model was suggested for ultra narrow gap welding system with Halmoy's model referenced for wire melting modeling. And the arc length in ultra narrow gap was defined. Secondly, based on the experimental results of up-and-down torch oscillation welding, phase shift of current and wire extension length were simulated for varying oscillation frequency to show that weld the bead shape in ultra narrow gap welding can be predicted. As the result, it was confirmed that reliable weld quality in ultra narrow gap welding can be achieved with up-and-down torch oscillation above 15Hz due to its ability to provide uniform heat input along the sidewall of gap.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.46-50
• /
• 2003

The horizontal fillet joint is one of the most important weld joints in the shipbuilding industry. High-speed rotating arc welding, which can increase the leg length, is an effective way to improve the weld productivity and quality for the horizontal fillet welding. Based on the Taguchi method, the effects of welding parameters on bead characteristics - leg length, asymmetry, undercut, overlap - are investigated fur high-speed welding process. As a result, the adequate welding parameters are selected for the required leg length, symmetric bead and no undercut. Besides, considerably consistent leg length is observed for the horizontal fillet welding with gap variation up to 3mm.

• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4112-4119
• /
• 2023

This study employs the microshear test method to examine the local mechanical properties of narrow-gap welded joints, revealing the mechanical inhomogeneity by evaluating the microshear strength, stress-strain curves, and failure strain. On this basis, the influence of weld joints micromechanical inhomogeneity on the crack tip opening displacement (CTOD) fracture toughness is investigated. From the root weld layer to the cover weld layer, the fracture toughness at the center of the weld seam demonstrates an increasing trend, with the experimental and calculated CTOD values showing a good correspondence. The microproperties of the welded joints significantly impact the load-bearing capacity and fracture toughness. During the deformation process of the "low-matching" microregions, the plastic zone expansion is hindered by the surrounding microregion strength constraints, thus reducing the fracture toughness. In contrast, during the deformation of the "high-matching" microregions, the surrounding microregions absorb some of the loading energy, partially releasing the concentrated stress at the crack tip, which in turn increases the fracture toughness.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.87-89
• /
• 2003

The yield strengths of austenitic stainless steel have been approximately doubled by increasing the nitrogen content. But, the increasing the nitrogen cause of increase the pressure of metal vapor inside the keyhole in electron beam welding. During welding, eruptions of keyhole often occur that cause excessive spatter, concavity, and porocity in the weld zone. Additionally the fast evaporation of nitrogen content cause of decrease the strength of weld zone. Therefore in this paper, we investigated of the weldability of electron beam welding and the change of chemical content after welding for strengthened austenitic stainless steel, measured the deformation scale of both of electron beam and narrow gap TIG and the spike fluctuation in the root.

• Journal of Welding and Joining
• /
• v.22 no.6
• /
• pp.57-63
• /
• 2004

Fracture toughness is an important parameter in designing offshore structures to ensure resistance to fracture at various temperatures. In this study, a series of experiments is carried out to obtain fracture toughness values (CTOD) of API 2W Gr.50B, welded using FCAW(Flux Cored Arc Weld). In particular, a comparison of absorbed impact energy and CTOD values are made with respect to two different welding groove shapes; double-V-groove and double-bevel-groove. Charpy impact tests are performed for specimens sampled near the root gap, and CTOD tests are carried out for three point bending specimens having the notch at weld zone. While Charpy impact test result is determined to be a good qualitative measure of fracture toughness, no quantitative correspondence between impact absorbed energy and CTOD values was found. Based on the experiment, it is observed that double-V-groove welds give lower transition temperature than those of double-bevel-groove.

• Journal of Welding and Joining
• /
• v.29 no.3
• /
• pp.64-69
• /
• 2011

Since welding process for most pipelines with large diameter has been carried out by the manual process, automation of the welding process is necessary for the sake of consistent weld quality and improvement in productivity. Therefore the development of the optimized algorithm to decide the welding condition is an effective technique to prove the feasibility of interface standards and intelligent control technology to increase productivity and reduce the cost of system integration. In this study, the pipe welding experiment has been carried out using plused GMA welding process to select optimal welding condition. And necessary information in root-pass welding has been obtained by applying in the pipeline using the selected welding conditions through the welding experiment.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.17-22
• /
• 2001

Because the quantitative relationships between welding parameters and welding result are not yet blown, optimal values of welding parameters for $CO_2$ robotic arc welding is a difficult task. Using the various artificial data processing methods may solve this difficulty. This research aims to develop an expert system for $CO_2$ robotic arc welding to recommend the optimal values of welding parameters. This system has three main functions. First is the recommendation of reasonable values of welding parameters. For such work, the relationships in between the welding parameters are investigated by the use of regression analysis and fuzzy system. The second is the estimation of bead shape by a neural network system. In this study the welding current voltage, speed, weaving width, and root gap are considered as the main parameters influencing a bead shape. The neural network system uses the 3-layer back-propagation model and a generalized delta rule as teaming algorithm. The last is the optimization of the parameters for the correction of undesirable weld bead. The causalities of undesirable weld bead are represented in the form of rules. The inference engine derives conclusions from these rules. The conclusions give the corrected values of the welding parameters. This expert system was developed as a PC-based system of which can be used for the automatic or semi-automatic $CO_2$ fillet welding with 1.2, 1.4, and 1.6mm diameter the solid wires or flux-cored wires.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.51-51
• /
• 2009

In order to understand the properties of high heat input welds made by electro gas welding, two kinds of low temperature steel were welded. Welding heat inputs were controlled by width of root gap and ranged from 118 to 143kJ/cm. Chemical composition and micro-structural analysis were performed. To understand low temperature impact properties, Charpy impact test was conducted at several temperatures. The results were summarized as follows; 1) Grain size of weld metal and heat affected zone was increased with an increase in welding heat input. 2) Impact test values at fusion line were severely fluctuated regardless of base metals, showing enormous difference among the values at the same test temperature.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.68-73
• /
• 2009

Recently, as titanium and titanium alloys are being increasingly used in wide areas, there are on-going researches to obtain high quality weld zone. In particular, growing interest is being drawn to laser welding, which involves low heat input and large aspect ratio in various welding processes and can facilitate shield in atmospheric condition compared with electron beam welding. The first report covered the analysis of embrittlement by the bead color of weld zone through quantitative analysis of oxygen and nitrogen and measurement of hardness as basic experiment to apply laser welding to titanium. Results indicated that the element that affect embrittlement the most was nitrogen, and as embrittlement and oxygenation go on, bead color changed to silver, gold, brown, blue and gray. This study performed butt welding of pure titanium and STS304 by using 1kW CW Nd:YAG laser, and to find out basic physical properties, evaluated welding performance by laser output, welding speed, root gap and misalignment etc, and examined mechanical properties through tensile stress and Erichsen test. The reason particles of pure titanium welded metal and HAZ are greater than STS304 is because they are pure metal and do not include many impure elements that work as nuclei in case of resolidification, thus becoming coarse columnar crystals eventually. In addition, the reason STS304 requires more energy during welding than pure titanium is because the particle size of base metal is smaller.