• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.2
• /
• pp.122-128
• /
• 2005

A feasibility study on the application of self?shielded flux cored arc welding to the on-site SM520 steel bridge box fabrication for express trains and high way construction instead of gas-shield flux cored arc welding was conducted in terms of weld soundness, mechanical properties, toughness and microstructures. All welded specimens made with the self?shielded FCAW process were tested by magnetic particle and ultrasonic techniques and they were found to be sound. All multipass weld specimens made with both self-shielded and gas-shielded FCAW processes showed yield and tensile strengths of $462{\sim}549\;MPa$ and $548{\sim}640\;MPa$, respectively. The impact values of Charpy V-Notch weld specimens also met with the required value of 40J at $-20^{\circ}C$. The hardness values of the top area of weldments were higher than those of the bottom area because of higher residual stresses in the near surface. It was found that welding characteristics of SM520 steel by the on-site welding conditions with self-shielded FCAW showed almost equivalent to those by gas-shielded FCAW in terms of sound welds, mechanical properties and microstructure.

• Journal of the Korean Society of Safety
• /
• v.7 no.1
• /
• pp.65-72
• /
• 1992

Objective of this research is to evaluate fracture behaviors of fresh-butt welded metal by the acoustic emission technique. The specimens used are medium carbon steel(SM45C), mild steel (SS41) and stainless steel(SUS304), which have different weldability. The similar welding and dissimilar welding processes are considered, in the former SM45C, SS41 and SUS304 are used, in the later the following metals are used SM45C and SS41, SM45C and SUS304 and SS41 and SUS304. The characteristics of fracture in weld metal are eshmated by the tension test with nominal speciemns, the fracture toughness test with compact tension specimens and fractography analysis. The results of tension test show for base metals and similar welding materials that the yield strength and ultimate strength of similar welding materials are increased, the elongation of those are decreased. The weldability of SUS304 is better than that of SM45C and SS41 In similar welding materials. Mechanical properties of dissimilar welding mateiiths we lower than those of similar welding materials. In dissimilar welding materials, the weldability of SM45C and SUS304 is better than that of SM45C and SS41, and also weidability of SS41 and SUS304 is better than SS41 and SM45C. Comparing mechanical properties with AE counts, it is found that AE conuts appeared on a small before the limit load of elasticity(P$_{e}$), and apper greatly near yield strength region in tension test. These results could contribute to the safety analyses and the evaluation of strength for welding structure.e.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.69-69
• /
• 2010

최근 컨테이너 선박의 초대형화로 극후물 고장력 강재인 항복응력 460MPa급 고장력강인 EH47이 개발되었다. 두께 80mm의 극후물 용접에서 용접생산성 향상을 위하여 EGW/FCAW로 양면 용접이 검토되고, 입열량은 최대 300kJ/cm의 대입열 용접이 요구된다. 이를 위해서는 강재 및 용접재료 모두 300kJ/cm 용접부 성능이 선급 규격을 만족하여야 함은 물론 마지막 조립단계에서 적용되기 때문에 용접재료의 용접작업성도 매우 크게 요구되고 있다. 먼저 대입열 용접금속에서 요구되는 저온 충격인성($vE_{-20^{\circ}C}{\geq}57J$)을 만족하기 위하여는 용접금속의 미세조직 제어가 필요하며, 특히 조대한 입계페라이트 생성을 억제하고 미세한 입내 페라이트를 균일 분포하는 것이 중요하지만, 이를 위해 용접금속의 소입성이 지나치게 높이면 경화조직인 베이나이트 분율이 증가하여 오히려 용접금속 저온 충격인성을 저하시키므로, 적절한 용접금속의 성분 제어가 중요하다. 한편 용접부는 선급에서 요구하는 최소 강도인 570MPa를 만족하기 위하여 용접금속의 소성구속 현상을 활용하여 용접부 인장강도를 확보 할 수 있음을 확인했다. 이를 위해서는 용접금속의 적정한 경화도 확보가 필요하였다. 전술한 바와 같이 대입열 용접금속 저온 충격인성 확보와 용접부 강도 측면을 고려하여 용접금속 최적의 탄소당량 범위를 제시코자 하였다. 한편 용접재료의 용접작업성은 EGW용접의 용적이행 현상은 자유비행이행으로 이루어지고 있으며 특성상 용접중 용적과 용융지 사이에 많은 순간단락 현상을 동반하고 있으며, 슬래그 유동이 불안정하면 아크 꺼짐 현상도 관찰되고 있다. 따라서, 현장용접시 원할한 용접작업성을 확보할 수 있는 평가 기준으로써 아크 전류 및 전압의 변동 정도를 설정하고, 용접재료의 용접작업성 확보 기준을 제시코자 하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.88-93
• /
• 2021

SAW (Submerged Arc Welding) is often used for ship construction or welding pressure vessels and involves spraying a flux in a powder form to a welding site to a certain thickness and continuously supplying electrode wires therein. This welding method enables high current welding up to 1,500 to 3,000 A. Arc efficiency is higher than 95% and the technique allows clean work as it creates less welding fume, which is composed of fine metal oxide particles, and the arc beam is not exposed. In this study, SM490C-TMC thick plates were heterogeneously welded by SAW. Mechanical properties of welds were measured, and welds were assessed macroscopically and for adhering magnetic particles. The following conclusions were drawn. Bending tests showed no spots exploded on sample surfaces or any other defect, and plastic deformation testing confirmed sufficient weld toughness. These results showed the 1F welding method has no shortcomings in terms of bending performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.649-656
• /
• 2019

Flux cored arc welding (FCAW), which is used widely in many fields, such as shipyards, bridge structures, construction machinery, and plant industry, is an alternative to shielded metal arc welding (SMAW). FCAW is used largely in the welding of carbon and alloy steel because it can be welded in all poses and obtain excellent quality in the field under a range of working conditions. In this study, the mechanical properties of welded parts were analyzed after different welding of SS400 and SM490A using FCAW. The following conclusions were drawn. The tensile test results satisfied the KS standard tensile strength in the range of 400~510 N/mm2 in all welding positions. The bending test confirmed that most of the specimens did not show surface breakage or other defects during bending and exhibited sufficient toughness, even after plastic deformation. The hardness test results were lower than the standard value of 350 Hv of KS B 0893. Similar to the hardness test, were greater than the KS reference value. The macro test revealed no internal flaws, non-metallic inclusions, bubbles or impurities on the entire cross section of the weld, and there were no concerns regarding lamination.