• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.8
• /
• pp.1865-1872
• /
• 2013

The social network services are grown rapidly through dissemination of smart devices. Therefore, increasing the data exponentially because many people use web services. Using these big data, it will be needed study of providing customized knowledge. So in this paper, we had collected data of 40 people for implementation of knowledge service using big data during one month. Based on these data, we had inferred information of location and moving type, and evaluated accuracy. Through that we had studied personal experience knowledge evaluation model for knowledge service.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.426-439
• /
• 2018

Purpose: To continuously monitor soil and climatic properties, a data acquisition system (DAQ) was developed and tested in plum farms (Gyewol-ri and Haechang-ri, Suncheon, Korea). Methods: The DAQ consisted of a Raspberry-Pi processor, a modem, and an ADC board with multiple sensors (soil moisture content (SEN0193), soil temperature (DS18B20), climatic temperature and humidity (DHT22), and rainfall gauge (TR-525M)). In the laboratory, various tests were conducted to calibrate SEN0193 at different soil moistures, soil temperatures, depths, and bulk densities. For performance comparison of the SEN0193 sensor, two commercial moisture sensors (SMS-BTA and WT-1000B) were tested in the field. The collected field data in Raspberry-Pi were transmitted and stored on a web server database through a commercial communications wireless network. Results: In laboratory tests, it was found that the SEN0193 sensor voltage reading increased significantly with an increase in soil bulk density. A linear calibration equation was developed between voltage and soil moisture content depending on the farm soil bulk density. In field tests, the SEN0193 sensor showed linearity (R = 0.76 and 0.73) between output voltage and moisture content; however, the other two sensors showed no linearity, indicating that site-specific calibration is important for accurate sensing. In the long-term monitoring results, it was observed that the measured climate temperature was almost the same as website information. Soil temperature information was higher than the values measured by DS18B20 during spring and summer. However, the local rainfall measured using TR 525M was significantly different from the values on the website. Conclusion: Based on the test results obtained using the developed monitoring system, it is thought that the measurement of various parameters using one device would be helpful in monitoring plum growth. Field data from the local farm monitoring system can be coupled with website information from the weather station and used more efficiently.

• Journal of Biomedical Engineering Research
• /
• v.26 no.2
• /
• pp.65-71
• /
• 2005

The main obstacles for adopting a mobile health information system to existing hospital information system are the redundancy of clinical data and the additional workload for implementing the new system. To obtain a seamless communication and to reduce the workload of implementation, an easy and simple implementation strategy is required. We propose a mobile clinical information system (MobileMed) which is specially designed for the easy implementation. The key elements of MobileMed are a smart interface, an HL7 message server, a central clinical database (CCDB), and a web server. The smart interface module transfers the key information to the HL7 message server as new clinical tests data is recorded in the existing laboratory information system. The HL7 message server generates the HL7 messages and sends them to the CCDS. As a central database the CCDS collects the HL7 messages and presents them to the various mobile devices such as PDA. Through this study we might conclude that the architecture for the mobile system will be efficient for real-time data communication, and the specially designed interface will be an easy tool for implementing the mobile clinical information system.

• Genomics & Informatics
• /
• v.5 no.2
• /
• pp.83-87
• /
• 2007

The analysis of DNA microarray data is a rapidly evolving area of bioinformatics, and various types of microarray are emerging as some of the most exciting technologies for use in biological and clinical research. In recent years, microarray technology has been utilized in various applications such as the profiling of mRNAs, assessment of DNA copy number, genotyping, and detection of methylated sequences. However, the analysis of these heterogeneous microarray platform experiments does not need to be performed separately. Rather, these platforms can be co-analyzed in combination, for cross-validation. There are a number of separate laboratory information management systems (LIMS) that individually address some of the needs for each platform. However, to our knowledge there are no unified LIMS systems capable of organizing all of the information regarding multi-platform microarray experiments, while additionally integrating this information with tools to perform the analysis. In order to address these requirements, we developed a web-based LIMS system that provides an integrated framework for storing and analyzing microarray information generated by the various platforms. This system enables an easy integration of modules that transform, analyze and/or visualize multi-platform microarray data.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.9
• /
• pp.4133-4136
• /
• 2015

Background: To analyze multi-source data including publications and patents, and try to draw the whole landscape of the research and development community in the field of gene therapy for breast cancer. Materials and Methods: Publications and patents were collected from the Web of science and databases of the five major patent offices of the world, respectively. Bibliometric methodologies and technology are used to investigate publications/patents, their contents and relationships. Results: A total of 2,043 items published and 947 patents from 1994 to 2013 including "gene therapy for breast cancer" were retrieved. The top five countries in global publication share were USA, China, Germany, Japan and England. On the other hand, USA, Australia, England, South Korea and Japan were the main producers of patents. The universities and enterprises of USA had the highest amount of publication and patents. Adenovirus- and retrovirus-based gene therapies and small interfering RNA (siRNA) interference therapies were the main topics both in publications and patents. Conclusions: The above results show that global research in the field of gene therapy for breast cancer is increasing and the main participants in this field are USA and Canada in North America, China, Japan and South Korea in Asia, and England, Germany, and Italy in Europe. Also, this article demonstrates the usefulness of bibliometrics to address key evaluation questions and define future areas of research.

• Steel and Composite Structures
• /
• v.20 no.3
• /
• pp.487-500
• /
• 2016

In order to investigate the flexural bearing capacity of panel zone of diaphragm-through joint between concrete filled square steel tubular column and steel beam, four specimens were tested under static tension loads to study the mechanical properties and bearing capacity of diaphragm-through joints with a failure mode of panel zone. Finite element models of these specimens were developed to simulate the test and compare the predicted failure modes, load-displacement curves and bearing capacities with the experimentally observed. It was found that the tensile load from the steel beam flange is mainly shared by the square steel tube and the diaphragm. The diaphragm plastic zone appears along the cross-section lines enclosed by the square steel tube and the influence of steel beam web on the plastic zone of the steel tube is significant and cannot be neglected. Computational models of yield lines on square steel tube and diaphragm are established based on the distribution pattern of the plastic zone, and an analytical method for the evaluation of the bearing capacity of the joint is proposed. The theoretical results and the experimental data are compared and found in good agreement.

• Proceedings of the Korean Society for Bioinformatics Conference
• /
• 2005.09a
• /
• pp.407-411
• /
• 2005

KUGI (Korean UniGene Information) database contains the annotation information of the cDNA sequences obtained from the disease samples prevalent in Korean. A total of about 157,000 5'-EST high throughput sequences collected from cDNA libraries of stomach, liver, and some cancer tissues or established cell lines from Korean patients were clustered to about 35,000 contigs. From each cluster a representative clone having the longest high quality sequence or the start codon was selected. We stored the sequences of the representative clones and the clustered contigs in the KUGI database together with their information analyzed by running Blast against RefSeq, human mRNA, and UniGene databases from NCBI. We provide a web-based search engine fur the KUGI database using two types of user interfaces: attribute-based search and similarity search of the sequences. For attribute-based search, we use DBMS technology while we use BLAST that supports various similarity search options. The search system allows not only multiple queries, but also various query types. The results are as follows: 1) information of clones and libraries, 2) accession keys, location on genome, gene ontology, and pathways to public databases, 3) links to external programs, and 4) sequence information of contig and 5'-end of clones. We believe that the KUGI database and search system may provide very useful information that can be used in the study for elucidating the causes of the disease that are prevalent in Korean.

• Information Systems Review
• /
• v.12 no.2
• /
• pp.89-104
• /
• 2010

Recently, ubiquitous sensor network (USN) has been applied to many areas including environment monitoring. A few studies applied the USN to disaster prevention and emergency management, in particular, aiming to conserve cultural heritage. USN is an useful technology to do online real-time monitoring for the purpose of early detection of the fire which is a critical cause of damage and destruction of cultural heritages. It is necessary to online monitor the cultural heritages that human has a difficulty to access or their external appearance and beauty are important, by using the USN. However, there exists false warning from USN-based monitoring systems without human intervention. In this paper, we presented an alternative to resolve the problem by applying ontology. Our intelligent fire early detection systems for conserving cultural heritages are based on ontology and inference rules, and tested under laboratory environments.

• Advances in concrete construction
• /
• v.17 no.2
• /
• pp.75-92
• /
• 2024

High Strength steel reinforced Reactive Powder Concrete (RPC) Beam is a new type of beams which has evident advantages than the conventional concrete beams. However, there is limited research on the shear bearing capacity of high-strength steel reinforced RPC structures, and there is a lack of theoretical support for structural design. In order to promote the application of high-strength steel reinforced RPC structures in engineering, it is necessary to select a shear model and derive applicable calculation methods. By considering the shear span ratio, steel fiber volume ratio, longitudinal reinforcement ratio, stirrup ratio, section shape, horizontal web reinforcement ratio, stirrup configuration angle and other variables in the shear test of 32 high-strength steel reinforced RPC beams, the applicability of three theoretical methods to the shear bearing capacity of high-strength steel reinforced RPC beams was explored. The plasticity theory adopts the RPC200 biaxial failure criterion, establishes an equilibrium equation based on the principle of virtual work, and derives the calculation formula for the shear bearing capacity of high-strength steel reinforced RPC beams; Based on the Strut and Tie Theory, considering the softening phenomenon of RPC, a failure criterion is established, and the balance equation and deformation coordination condition of the combined force are combined to derive the calculation formula for the shear bearing capacity of high-strength reinforced RPC beams; Based on the Rankine theory and Rankine failure criterion, taking into account the influence of size effects, a calculation formula for the shear bearing capacity of high-strength reinforced RPC beams is derived. Experimental data is used for verification, and the results are in good agreement with a small coefficient of variation.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.7
• /
• pp.369-374
• /
• 2015

This study analyzed analyzes the energy performance of six houses in Daejeon completed which were built in 2011. Observed The observed houses, which were all designed and constructed inof the same size and structure, are were highly insulated with triple Low-E coating windows; the insulation level of the walls is was $0.13W/m^2K$ and that of the roof is was $0.10W/m^2K$. As electric houses, all of the energy supplied to the houses, including for cooking, is was supplied by electricity. A and 3~4 kWp of photovoltaic system and a 3~5 kW of ground source heat pump (GSHP) were installed in each house tofor providing provide space heating/and cooling and hot water are installed. We constructed a Web-based remote monitoring system in order to understand energy consumption and the dynamic behavior of the energy system. T, and the results of our metering data analysis of 2013 are as follows. First, the annual residential energy consumption is was 4,400 kWh (${\sigma}=1,209$) and GSHP energy consumption is was 5,182 kWh (${\sigma}=1,164$). Second, residential energy consumption ranked highest in average energy usage, with at 45% of the total, followed by heating with at 30%, hot water supply with at 17% and cooling with at 6%. Third, the average energy independence rate is was 51.8%, the GFA (Gross gross floor area) criteria average energy consumption unit is was $48.7kWh/m^2yr$ (${\sigma}=10.1$), and the net energy consumption unit (except the energy yield of the PV systems) is was $24.7kWh/m^2yr$ (${\sigma}=8.8$).