• 한국소음진동공학회논문집
• /
• 제16권9호
• /
• pp.904-911
• /
• 2006

A modified energy method for the fretting wear of the steam generator tube is proposed to calculate the wear-out depth between the nuclear steam generator tube and its support. Estimation of fretting-wear damage typically requires a non-linear dynamic analysis with the information of the gap velocity and the flow density around the tube. This analysis is very complex and time consuming. The basic concept of the energy method is that the volume wear rate due to the fretting-wear phenomena Is related to work rate which is time rate of the product of normal contact force and sliding distance. The wearing motion is due to dynamic interaction between vibrating tube and its support structure, such as tube support plate and anti-vibration bar. It can be assumed that the absorbed work rate would come from turbulent flow energy around the vibrating tube. This study also numerically obtains the wear-out depth with various wear topologies. A new dissection method is applied to the multi-span tubes to represent the vibrational mode. It turns out that both the secondary side density and the normal gap velocity are important parameters for the fretting-wear phenomena of the steam generator tube.

• 한국재료학회지
• /
• 제12권8호
• /
• pp.608-612
• /
• 2002

The sliding wear behavior of an iron-base NOREM 02 hardfacing alloy was investigated in the temperature range of $25～250^{\circ}C$ under a contact stress of 103MPa (15ksi). With increasing temperature, the wear loss of Norem 02 in water increased slightly up to $180^{\circ}C$ at which Norem 02 showed the wear loss of 2.1mg. The wear resistance of Norem 02 resulted from the surface hardening due to the strain-induced phase transformation from austenite to $\alpha$'martensite during sliding wear. The wear loss of Norem 02 was smaller in water compared to air at same temperature because the water could be served as a sort of lubricant. The wear mode of NOREM 02 changed abruptly to severe adhesive wear at $190^{\circ}C$ and galling occurred above $200^{\circ}C$. It was caused that the strain- induced phase transformation took place below $180^{\circ}C$ while not above $190^{\circ}C$. Therefore, Norem 02 was considered to be inadequate at high temperature service area.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.369-374
• /
• 2004

Web-based analysis programs for reliability assessment of machine tools were developed in this study. First, the reliability data analysis program was developed to search for failure rate using failure data and reliability test data of mechanical part. Second, failure mode analysis was developed through performance tests like circular movement test vibration test for machine tools. This analysis program shows correlation between failure mode and performance test result. Third, tool life was predicted by correlation between flank wear and cutting time, using the extended Taylor tool life equation in turning data and the equivalently converted equation in order to apply ball endmill data to Taylor tool life equation in milling data. All the information related to input and result data can be stored in theses programs.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.577-582
• /
• 1997

The mechanical properties of Al2O3-ZrO2 composites fabricated by RBAO(reaction bonded aluminium oxide) process were investigated. As the amount of ZrO2 increased the sinstered density of Al2O3-ZrO2 composites decreased slightly, but wear resistance was enhanced. Bending strength of Al2O3-ZrO2 composites increased in proportion to the amount of al in case of a fixed ZrO2 content. When the amount of Al was fixed bending strength reached its maximum value at 25 wt% ZrO2. The fracture toughness(K1c) increased with increasing content of ZrO2, but decreased with increasing Al amount. On the other hand, the fracture mode of Al2O3-ZrO2 composites was the mixed mode of inter-and transgranular fracture.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.260-266
• /
• 2002

In this study, the effects of oxide layer farmed on the wear tracks of TiN coated silicon wafer on friction and wear characteristics were investigated. Silicon wafer was used for the substrate of coated disk specimens, which were prepared by depositing TiN coating with 1 ${\mu}{\textrm}{m}$ in coating thickness. AISI 52100 steel ball was used fur the counterpart. The tests were performed both in air for forming oxide layer on the wear track and in nitrogen to avoid oxidation. This paper reports characterization of the oxide layer effects on friction and wear characteristics using X-ray diffraction(XRD), Auger electron spectroscopy(AES), scanning electron microscopy (SEM) and multi-mode atomic force microscope(AFM).

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.406-411
• /
• 2001

This paper shows the failure(wear) phenomena of automotive transmission bearings and investigate their characteristics. It was found that the wear mechanism was mainly abrasive wear by the presence of particles in the gear box and the balls was weared more severely than the other tribological contacting parts. The wear of balls alter the bearing contact angle and load ratings, and finally it cause the bearing failure. With close examination of the failed bearing, various countermeasures could be suggested.

• 동력기계공학회지
• /
• 제14권6호
• /
• pp.83-88
• /
• 2010

The wear behavior of epoxy matrix composites filled with nano sized silica particles is discussed in this paper. Especially, the variation of the coefficient of friction and the wear resistance according to the change of apply load and sliding velocity were investigated for these materials. Wear tests of pin-on-disc mode were carried out and the wear test results exhibited as following ; The epoxy matrix composites showed lower coefficient of friction compared to the neat epoxy through the whole sliding distance. As increasing the sliding velocity the epoxy matrix composites indicated lower coefficient of friction, whereas the neat epoxy showed higher coefficient of friction as increasing the sliding velocity. The specific friction work of both materials were increased with apply load. In case of the epoxy matrix composites, the running in periods of friction were reduced as increase in apply load. The epoxy matrix composites were improved the wear resistance by adding the nano silica particles remarkably. It is expected that the load carrying capacity of the epoxy matrix composites will be improved by increase of Pv factor.

• 한국컴퓨터정보학회논문지
• /
• 제20권11호
• /
• pp.1-8
• /
• 2015

Flash memory has advantages in that it is fast access speed, low-power, and low-price. Therefore, they are widely used in electronics industry sectors. However, the flash memory has weak points, which are the limited number of erase operations and non-in-place update problem. To overcome the limited number of erase operations, many wear leveling techniques are studied. They use many tables storing information such as erase count of blocks, hot and cold block indicators, reference count of pages, and so on. These tables occupy some space of main memory for the wear leveling techniques. Accordingly, they are not appropriate for low-power devices limited main memory. In order to resolve it, a wear leveling technique using bit array and Bit Set Threshold (BST) for flash memory. The proposing technique reduces the used space of main memory using a bit array table, which saves the history of block erase operations. To enhance accuracy of cold block information, we use BST, which is calculated by using the number of invalid pages of the blocks in a one-to-many mode, where one bit is related to many blocks. The performance results illustrate that the proposed wear leveling technique improve life time of flash memory to about 6%, compared with previous wear leveling techniques using a bit array table in our experiment.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.18-23
• /
• 2005

This study deals with the friction and wear characteristics of C-N coated SCM415 steel. The PSII(plasma source ion implantation) apparatus was built and a SCM415 test piece with steel substrate was treated with carbon nitrogen by this apparatus. The composition and structure of the surface layer were analyzed and compared with that of PVD(physical vapor decomposition) coated TiN layer. It was found that both of friction coefficient of C-N coating and TiN coating decreased with increasing load, however, C-N coating showed relatively lower faction coefficient than that of TiN coating. The micro-vickers hardness of C-N film is 3200 Hv, which is $32\~43\%$ higher than that of TiN film. The critical load of C-N film is 52N, which is $25\%$ higher than that of TiN film. The hardness of C-N film fabricated by Plasma ion implantation is $61\~70\%$ higher than that of base material, and faction coefficient is $14\~50\%$ lower than that of base material. It is also interesting to note that the friction was changed from adhesive wear mode to light oxidizing wear mode.

• 복식문화연구
• /
• 제7권6호
• /
• pp.98-115
• /
• 1999

As sports infiltrates each field of modern society and becomes familiar, sports wear was changed functionally and was introduced and enveloped into everyday dress. Modern sports wear has been the settled in everyday life deeply and become the clothes of life which are worn regardless of place, time and age. The aim of this paper was to clarify what kind of fashion of sports style would be given to the modern people. In this study, sports wear which has become everyday dress classified from a gender point of view. It was divided into masculine image, feminine image, and neutral image. Sports wear of masculine image generated a silhouette which emphasized the shoulder with the aspiration for youth and health. Wide shoulder was considered as the symbol of masculine beauty and the expression of healthy beauty. It was reflected well in body conscious look. And owing to the development of up-to-data materials, innovation of design, and the study of human body technology, the functional character was settled in the sports wear which showed masculine image. Sports wear of feminine image was represented fashion of body exposure, body feet with body conscious look, and romantic mode. This image was expressed fashion as comforts, pleasant, active design, materials, color, and romantic feminine beauty. Sports wear of neutral image was expressed into unisex clothes. This cloths have no difference in gender, age, and class. It was used as casual sports wear. In the 1960s, young generation participated in such street sports as street basketball and skate. They usually sore the sports wears of neutral image such as cycling, skating, and ski. In the materials of sports, the development of up-to-data material like lycra made the sayings lifelike, “up-to-data material is the second skin” It show that glamorous feminine image and strong masculine image coexisted. The contemporary concept of sportswear is no longer limited to those clothes for sports found in such places like tennis court or swimming pool. Now, the sports wear become more like casual activity wear all classes of people can enjoy in their life regardless of where they are, when they wear, and even how old they are.